Cisco Routers :: No Access Information Logged For PPTP Server On RV042?

Nov 25, 2012

I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?

View 4 Replies


Linksys Wired Router :: Configure Cisco RV042 To Access PPTP VPN Server?

Jun 7, 2012

how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.

View 1 Replies View Related

Linksys Wired Router :: Static Route To Access TMG Internal Network Through RV042 Pptp Server?

Mar 20, 2012

Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 ( ---> TMG [external] ( ---> TMG [internal] ( Is there any way through static route to access the TMG internal network through RV042 pptp server?

View 1 Replies View Related

Cisco Routers :: RV042 Setting Up PPTP VPN

Sep 21, 2012

My network to use a RV042 router.  It is connected to my cable modem and working well.  I may add a DSL connection later in the month as a backup.  All I really want to do now is setup my PPTP VPN connection.  I have not been able to find a guide so I will assume it isn't that bad.   I set up 2 accounts in the VPN-PPTP Server screen.  Built my connection on my android phone and voila nothing works.  So I tried to disable the "Block WAN requests".  I tried port forwarding the VPN to (address of the router) and no luck.   AT this point I am stuck.   I know my infrastructure is right because from outside the network I can [URL] and see my router configuration.  Now if I could just get a simple PPTP connection

View 7 Replies View Related

Cisco Routers :: Cannot Browse Network With Rv042 Pptp Connection

Nov 1, 2011

My network consists of the following:
Office-RV042 with static IP ->SBS2003 (
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"

View 2 Replies View Related

Cisco Security :: Can Configure A PIX (515) As PPTP Client To Establish A Tunnel With PPTP Server

May 15, 2006

Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.

View 5 Replies View Related

Cisco Routers :: RV180 PPTP VPN Server Limitation?

Oct 29, 2012

For the past week, I have tried to setup the PPTP VPN server on the RV180. The setup was straight forward, but I could not log-on no matter what I tried. I decided to call Cisco small business support, and as I was talking to the engineer, it mysteriously started to work. I was puzzled and somewhat embarrassed because I'd hate to admit it was an id10t problem on my part. As I tried a few different configurations, I began to realize there might be a limitation in the RV180 PPTP VPN server with the current firmware (
In short, the RV180 PPTP only works with subnet. My setup has 3 vlans: vlan1 in subnet, vlan2, and vlan3 My originally plan was to keep vlan3 isolated by disabling inter-vlan routing, but I needed a way to manage a couple of devices on vlan3 remotely, thus I wanted to setup a VPN in the subnet. This turned out to be the reason why it never worked before. Today when I called Cisco support, I assigned the PPTP VPN server a ip range, and it worked. Later, I tried assigning or ip addresses to the PPTP VPN server, and they both failed to work. I created another test vlan4 with subnet, and assigned the PPTP VPN server to that vlan, and it worked again.
I'd like to mention that I already configured the subnet with a few devices before I replaced my router with RV180, and I don't want to have to change and test the setup of all the devices. Another reason I want to have my VPN server outside the range is that it's way too commonly used by wifi hotspots that it increases the chance of wifi and vpn in the same subnet.
I can test a few more configurations, but I think the results will be the same. Perhaps Cisco should test the RV180 in the lab to confirm what I found.

View 2 Replies View Related

Cisco Routers :: RV016 PPTP Server And Block MAC Address

Apr 2, 2013

So if the PPTP server is enabled, and "Block MAC address not on the list" is enabled under the DHCP settings, will the PPTP client get an IP address?Similarly, if the PPTP server is enabled and the range of IP addresses configured on the PPTP server screen is outside the IP range of the router due to a subnet mask (like for example), will the IP still be assigned to the PPTP client? If assigned, will that IP have any connectivity to the LAN?

View 1 Replies View Related

Cisco Routers :: RV220W Not Working With PPTP Server On One VLAN Only

May 5, 2012

I possess a RV220W (firmware but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in I created a VLAN ID 10 in inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range to

To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.

View 3 Replies View Related

Belkin Routers :: N750 Cannot Connect To Firmware Information Server

Oct 25, 2012

I have a n750 and I did the firmware update on the router and I have it check for firmware updates when I log in and i keep getting this message: "Cannot connect to the firmware information server,please double check the WAN connection." I have access to the internet.

View 14 Replies View Related

Cisco Routers :: RV 120W Port Forwarding 1723 To A PPTP Server

Sep 11, 2011

We have just acquired a Cisco RV120W Firewall Router and we are experiencing issues with this router. I've read some threads related to port forward issue with RV120W before writing this new topic.
We have 2 locations (site A and site B) connected with a Site to Site VPN (PPTP) running under Windows Server 2008 R2 with TMG 2010. This Site to Site VPN worked very well until we replaced our old router with the RV120W at site B. Since this moment, our engineers are not able to make the site to site VPN work again. The TMG box are located just behind the router.
We have followed some threads about Port Forwarding but it did not solve our issue (others port forwarding rules for RDP for example work). Our RV120W is running the last stable firmware ( provided by Cisco.

View 1 Replies View Related

Cisco Routers :: RVS4000 Distribute A Search Domain In Addition To IP Address / DNS Server Information

Feb 29, 2012

I have just installed and configured a new RVS4000 with VPN (currently running firmware V2.0.0.3), and have enabled the DHCP Server service. I wanted to be able to distribute a search domain in addition to the IP address and DNS Server information (as I have done with other devices that include a DHCP Server), but cannot seem to locate where or how I might do that with the RVS4000.

View 4 Replies View Related

Cisco Routers :: RV110W Unable To Access Other Subnets When Using PPTP VPN

Jan 1, 2013

I've encountered a problem when using PPTP VPN to access my network. I can connect in and able to ping the hosts connected to the RV110W. [code] On the local network, I am able to ping the hosts in 192.168.250.x from 192.168.251.x and vice versa.Static routes are configured to ensure that all networks are reachable.The problem comes when I tried to VPN (PPTP) in from a remote location using the Windows XP's built in default VPN dialer.When connected, I can ping all the hosts on segments, but when I tried to ping the hosts in and segments, I get a request timeout.
The routing table on the RV110W shows the gateway for (the VPN IP address) as and interface is WAN.What am I missing and how should I configure the RV110W so that I can access the other subnets through VPN?

View 6 Replies View Related

Cisco VPN :: PPTP Not Working On IPad Through RV042

Sep 15, 2011

I have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?

View 1 Replies View Related

Cisco Routers :: RV220W PPTP Users Unable To Access Subnet Across Tunnel

Apr 21, 2012

I have two offices connected with an IPSEC VPN tunnel using RV220W routers.  The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x).  I have also set up PPTP users for remote access.  PPTP users that connect to site 1 cannot access site 2 and vice versa.   The PPTP users have no trouble accessing the resources on the site that they connect to.  I have tried activating RIP and adding various static routes with no success.  If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.

View 2 Replies View Related

Cisco Routers :: RV042 Can't Ping Ip Server

Feb 6, 2012

i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC  , if   I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF"  on all of those servers.  the result is same, failed.

View 0 Replies View Related

Cisco Routers :: RV042 With Two Subnets For A Web Server?

Dec 21, 2011

I have a static DSL  connection and my ISP is giving me 4 static IP's. I have connected my  RV042 to the DSL modem and I have now 1 subnet at What I  want to create is a WEB server/ Email server, but to sit on a different  subnet - For now I have connected the server to the DMZ  port, but I am unable to to access it from WAN, only from LAN. How to configure properly the 2 subnets ( and and how to forward my static address to the server which I  which to be on the

View 4 Replies View Related

Cisco Routers :: RV042 Can't Locate DNS Server

Dec 14, 2012

I'm trying to set up an RV042 as a gateway for our home network. I've cloned the MAC address of the cable modem attached to WAN1, and have set up WAN1 to obtain an IP automatically. The System Summary page shows under WAN Status that WAN1 has been assigned an IP address in the right range for Comcast, the provider. The default gateway address looks good, and the DNS server is, in fact, Comcast's main DNS server for this area.
However, when I go to System Management > Diagnostic, the router is unable to resolve basic domain names (e.g., or ping addresses outside the LAN. I can ping the router itself successfully. Attempts to access the web through the router fail on domain name look.

View 4 Replies View Related

Cisco Routers :: RV042 Giving Out Certificate Instead Of Server?

Jan 28, 2013

RV042 router is giving out the outer certificate  instead of server certificate. Outlook anywhere is failing and we are receiving certificate errors for any secure site behind this firewall.  I'm not talking  about remote  management. I'm talking about people trying to access our  web site,  which is secured, and getting an error because the RV042 is  giving its  own SSL certificate instead of the Server's certificate.  Firmware Version:  I don't see any updates for that  hardware.  I do have it working on an RV042 with the same firmware at a different location.  How do we turn that off or keep it from happening?  Output from a test site Attempting to resolve the host name xxxx in DNS.The host name resolved successfully. Additional DetailsTesting TCP port 443 on host xxxx to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps ExRCA is attempting to obtain the SSL certificate from remote server xxxx on port 443. ExRCA successfully obtained the remote SSL certificate. Additional Details Remote  Certificate Subject:

SN=California, L=Irvine, C=US, O="Cisco-Linksys,  LLC", OU=RV042, CN=68:ef:bd:b8:0f:78, Issuer: SN=California, L=Irvine,  C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host  name xxxx doesn't match any name found on the server  certificate SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC",  OU=RV042, CN=68:ef:bd:b8:0f:78.

View 1 Replies View Related

Cisco Routers :: RV042 V3 - How To Activate Telnet Server

Jan 25, 2012

I wish to change ARP table or any else to get a WOL functionnality.
I found how to activate telnet server, but I don't have the right login and password.

View 1 Replies View Related

Cisco Routers :: Multiple Internal Web Server RV042

Aug 15, 2012

We have setup a new internal web server so now we have two internal web server and both or hosting sites on port 80. Currently we have port 80 forwarding to one of the web servers and users are able to hit it from the outside. 

Is there any way to configure the RV042 to route web traffic to the correct web server by using the site name or dns?  If a user puts in the address{URL}, be routed to one web server but if they put in {URL}, be routed to our second web server.   I've checked with our vendors and the both web servers applications need to run on port 80.  If we have forwarding setup on the RV042 to forward port 80 to web1 then users can't access web2 from the outside?

View 3 Replies View Related

Cisco VPN :: PPTP Tunnel To Linksys RV042 Not Working Through 2620 Router

Jan 9, 2012

I have a remote location that has a Linksys/Cisco RV042 router [URL] that allows PPTP connections based on username and password combinations. There are no intermediary routers between this device and the internet - only a DSL modem. A secondary WAN connection is not present.
I am able to dial into this VPN using the Windows XP and Windows 7 dialers from any of my local free-wifi locations(e.g. Starbucks). I WAS able to connect to this VPN connection from my house when my home router was a Buffalo brand router.
I have replaced the Buffalo router with a 2620(non-XM) that is connected in ROaS fashion to a 2950 switch. I need some guidance on what in my config is not allowing me to connect to this remote site.
Home network info: Local subnets : 192.168.x.x
Remote network info: Local subnet : 10.214.x.x
The Windows XP dialer client indicates that the username and password challenge is where the connection fails. It ultimately gives me the error code 619. I have performed a Wireshark packet capture of an attempt to connect from ip This packet capture shows multiple "Configuration Request" packets being exchanged between the two endpoints, but does not ever show an exchange of authentication.
My nat translation table shows an entry for both a GRE tunnel as well as port 1723 between and the WAN port of the RV042 when attempting to establish this VPN.
I have attached my 2620 configuration for your review.

View 1 Replies View Related

Cisco Routers :: RV042 Giving Out Router Certificate Instead Of Server

Nov 28, 2012

Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)

View 5 Replies View Related

Cisco Routers :: Configure RV042 Dual WLan / Web And DNS Server

Aug 19, 2011

I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN

View 1 Replies View Related

Cisco Routers :: RV042 Email Server Not Send Mail When Switch From Wan

Sep 28, 2011

Just installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.

View 0 Replies View Related

Cisco Routers :: RV042 - DHCP Giving Out Wrong Default Gateway And DNS Server

Oct 3, 2012

I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it.  I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router
IP of DHCP Server (the one that is being handed out):
IP of DNS (the one that is being handed out):
What I want to it be.
IP of Router:

View 3 Replies View Related

Cisco Routers :: RV042 - How To Allow Facebook Access Between 12 And 1 Pm Only

Jan 12, 2011

I have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm.  However The settings never seem to take. Is this a bug in the system?  If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.

View 2 Replies View Related

Cisco Routers :: Access RV042 Through Telnet?

Jun 20, 2011

I am trying to access my RV042 through telnet. I go to
which enables telnet. However when I type my username and password it will not authenticate.

View 16 Replies View Related

Cisco Routers :: Can RV042 Access The Internet

Jul 9, 2012

I am new to implementing VPN service.  What I would like to do is  install a RV042 or RV082 (for added speed) and configure it to allow me  to access the Internet (from home base) through the VPN from any  location  while on the road and using my laptop.  My questions are: Can this be  done?  If so, what needs to be done in the configuration to allow gateway  access to the Internet? I can't find any reference in the Cicso  documents, but somewhere I saw that it can be done.  I don't care about  accessing anything on the local LAN.  As I would be using the same  Internet connection for the VPN and the access to get out----how would  this affect speed?  I plan to use Quick VPN as the client, and haven't  even touched the client issue. 

View 5 Replies View Related

Cisco Routers :: Cannot Access VPN Anymore From RV042

Jun 8, 2012

I had this problem where 2 users could only access my RV042 vpn one at a time
The Linksys solution was to give these 2 users a RV042 as well. That worked, 2 can access my vpn at the same time. We use QuickVPN for this purpose
But now there users cannot access another Cisco vpn any more in our office. I attach a schematic and a screen shot of the error when trying to connect to the professional vpn  with vpn client version

The 2 notebooks epresent the 2 users
The one at the bottom is my vpn
The connection on the left is the professional vpn
We now use remote desktop to my vpn to get to the professional vpn, that work but we don't like it

View 2 Replies View Related

Cisco Routers :: RV042 - Allow LAN To Access Internet?

May 2, 2012

I configure my new purchase RV042 router, in Access Rule i Deny all services the source is Lan and destination is WAN. my concern is i want to allow LAN to access internet, so i'ved create another rule which allow http, https. but my problem is i cannot access internet.

View 4 Replies View Related

Cisco Routers :: RV042 - Access Web Admin

Jun 12, 2012

brand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
hardware broken?

View 3 Replies View Related

Cisco VPN :: 5505 - Logged In VPN Can't Access DMZ From Internal Network

Apr 9, 2012

What I got is a 5505 ASA firewall and I'm connected to it via VPN.  I'm pulling an 192.168.169.x address because that's what we set their company's internet LAN to.  Which is what we want.  What I can't do while I'm VPN'd in is ping from the internet network to the DMZ, and the same when I try and ping from the DMZ to the internal network.
The DMZ is on a 196.0.0.x network.The internet network is 192.168.169.x network.
I don't need them to have internet access on the DMZ I just want to be able to access it from the internal network.  What is going on is we need them to be able to VPN into the DMZ and access their equipment.  At this point it would just make me happy to be able to ping from the internal network to the DMZ and I can figure it out from there I've setup rules and applied them and when I wasn't having success I referred back to defaults.  Right now the rules are set at default, any thing in and anything out, on both internal and DMZ.  I'm using a VPN client and going through Cisco ASDM Launcher to setup the rules and static routes, I haven't done anything with the command line.  All the research I've done everyone does it command line, I find it easier to do it GUI.  This is my first time working with an ASA firewall.

View 2 Replies View Related

Copyrights 2005-15, All rights reserved