Cisco Routers :: Cannot Browse Network With Rv042 Pptp Connection
Nov 1, 2011
My network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
View 2 Replies
ADVERTISEMENT
Sep 21, 2012
My network to use a RV042 router. It is connected to my cable modem and working well. I may add a DSL connection later in the month as a backup. All I really want to do now is setup my PPTP VPN connection. I have not been able to find a guide so I will assume it isn't that bad. I set up 2 accounts in the VPN-PPTP Server screen. Built my connection on my android phone and voila nothing works. So I tried to disable the "Block WAN requests". I tried port forwarding the VPN to 192.168.1.1 (address of the router) and no luck. AT this point I am stuck. I know my infrastructure is right because from outside the network I can [URL] and see my router configuration. Now if I could just get a simple PPTP connection
View 7 Replies
View Related
Nov 25, 2012
I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?
View 4 Replies
View Related
Mar 20, 2012
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies
View Related
Sep 12, 2012
I am having problem when try to connect through VPN from MacOS to my RV016 router.The situation is like this. I can connect to the router,the connection is succesfull, but when I try access resources inside the network it disconnects me.The message is "You are dissconnected by the PPTP Server". I encountered this problem on MacOS Snow Leopard and Lion. I tried to connect from 3 different Apple machines, but the problem is the same.
View 1 Replies
View Related
Jun 4, 2012
I've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
View 6 Replies
View Related
Feb 18, 2013
I am working with a RV180w and need to map drives from the internal network to the VPN client but whenever I try to connect to a shared drive I continue to get authentication messages from the DC. Any useful guide for configuration in this scenario. Internal subnet is on Windows 2008 domain.
View 1 Replies
View Related
Jan 23, 2012
i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
View 1 Replies
View Related
Sep 15, 2011
I have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
View 1 Replies
View Related
Jan 31, 2012
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
Cisco RV 180W
Firmware Version:1.0.1.9
View 7 Replies
View Related
Jan 9, 2012
I have a remote location that has a Linksys/Cisco RV042 router [URL] that allows PPTP connections based on username and password combinations. There are no intermediary routers between this device and the internet - only a DSL modem. A secondary WAN connection is not present.
I am able to dial into this VPN using the Windows XP and Windows 7 dialers from any of my local free-wifi locations(e.g. Starbucks). I WAS able to connect to this VPN connection from my house when my home router was a Buffalo brand router.
I have replaced the Buffalo router with a 2620(non-XM) that is connected in ROaS fashion to a 2950 switch. I need some guidance on what in my config is not allowing me to connect to this remote site.
Home network info: Local subnets : 192.168.x.x
Remote network info: Local subnet : 10.214.x.x
The Windows XP dialer client indicates that the username and password challenge is where the connection fails. It ultimately gives me the error code 619. I have performed a Wireshark packet capture of an attempt to connect from ip 192.168.10.11. This packet capture shows multiple "Configuration Request" packets being exchanged between the two endpoints, but does not ever show an exchange of authentication.
My nat translation table shows an entry for both a GRE tunnel as well as port 1723 between 192.168.10.11 and the WAN port of the RV042 when attempting to establish this VPN.
I have attached my 2620 configuration for your review.
View 1 Replies
View Related
Jun 7, 2012
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies
View Related
Oct 23, 2011
I have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
View 4 Replies
View Related
Jul 4, 2012
I have an issue with Cisco RV042 i have two Internet access connection from my ISP one with 30Mbps and the other with 8Mbps.
i have 30Mbps in WAN1 and 8Mbps on WA2
my issue that i was connecting both of the WAN connections using DHCP mode and it was working fine and the ISP modem was terminating the PPPOE
now i decided to use PPPOE on the Cisco RV042 and change the ISP modem to bridge mode.
WAN1 is working were as WAN2 is not working.
i tried to factory reset, shift links, in all cases WAN2 if its on PPPOE does not go up.
i am using latest firmware from cisco.com.
View 4 Replies
View Related
Nov 19, 2012
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, but both Routers unable to ping each other and I can't remotely administer each router through the VPN connection.
View 1 Replies
View Related
Sep 4, 2011
At this moment I'm trying to connect 2 router rv042 and i received the following error message
(g2gips0) #23: ERROR: asynchronous network error report on eth1 for message to 190.199.164.144 port 500, complainant 190.199.164.144: Connection refused [errno 146, origin ICMP type 3 code 3 (not authenticated)]
in the other router i don't see any error . what would be the problem.
View 5 Replies
View Related
Nov 15, 2010
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
View 6 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
May 31, 2012
In the company that I'm currently working, we have one gateway with LAN IP address 172.16.0.1 and netmask /23 [=255.255.254.0]. In this gateway, there's a DHCP server providing 510 IP addresses in its pool.
I need to substitute the server, replacing it with a RV042. This afternoon, when I was configuring this router, I noticed that it doesn't let you configure different netmasks, since it comes with some of them predefined [starting in 255.255.255.0 and so on], as shown in the picture below:
I need to provide DHCP for this /23 network, but it seems that DHCP field cannot assign /23 networks.
View 4 Replies
View Related
Jul 14, 2012
I am having difficulty with gateway to gateway vpn on RV042.I have site A and site B, both have static IP address,local IP at site A is 192.168.1.0 local IP at site B is 192.168.5.0I have configured each site as directed in the documentation, the sites connect ok within the admin consoles, I cannot browse any resources from either site. Site A is a domain.local and I am part of that domain at site B. I can ping site B local address from site A and vice versa however I can not ping any of the servers or NAS devices on either network. the only device I can ping successfully inside the network is a phone server (splicecom unit).
I have read various posts in the discussion boards but have found no resolve. Internet access is fine from either site. I think that it could possibly be a DNS issue but am unsure, should I add DNS entries in the advanced section, if so what DNS would I enter?
View 5 Replies
View Related
Nov 15, 2012
I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN side and I installed RV042's at the clients as well.This may look like overkill but believe me, it gives peace of mind, it made things a whole lot better, everybody happy.I am going to set up tunnels but for the time being the clients use QuickVPN. The above setup is all good if people access the vpn from the same source.
I now have a problem where one of our people is in Vietnam and she cannot access the vpn due to the "verifying network" loop.Looking at the log everything looks great, I compared a successful connect with an unsuccessful one and the logs are identical.The only difference is that the final ping is blocked (recorded in the QuickVPN log on the client side).The client uses W7 with firewall on.No need to repeat suggestions, such as turing printer sharing off, I have been through all that. isn't this simply caused by the ISP in Vietnam blocking pings ?
View 2 Replies
View Related
Nov 15, 2011
I keep getting an error when trying to use the Microsoft Link layer Topology discovery. It claims there the is either network delays or an incompatible router on the network.
Actual error:
"Responses from other devices on the network are delayed or there is an incompatible router on the network"
I have 2 RV042 routers, one for each of our network connections. So I am assuming this is the source of the error.
View 3 Replies
View Related
May 15, 2006
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies
View Related
Sep 13, 2011
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
View 5 Replies
View Related
Nov 26, 2011
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies
View Related
Nov 2, 2011
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Dec 15, 2011
an RVS4000 shall establish a pptp VPN connection. The router is connected trough its WAN port to the first router which connects to the internet.
The PPTP VPN connection cannot be established but the pptp server can be pinged from the VPN router. Login data and password is OK. Connection can be established from a win7 computer without any problem.
View 3 Replies
View Related
Mar 6, 2011
We have a Cisco 891 with this configuration belowI got several computer on my lan that needs to connect to an external Windows server with pptp. The windows server is not mine but it works. The clients are using the windows connection manager. We can connect to the windows pptp server for hours sometimes.But, sometimes we can just connect about 3-4-5 minutes, and it auto-disconnects. Is there something wrong in my configuration ? I heard the cisco router is messing with the keepalive or the connection state.It seems to happens when i have more than 5-6 clients connected at the same time on the same server. I got theses mesages : Link to VPN failed. OR ERROR 619 OR ERROR 651Before, I had a RV042 and it worked like a charm. We were 10 on the vpn server and it was working. I dont see why Its not working now.
version 15.0no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname Quantis891!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication login local_authen localaaa authorization exec local_author local !!!!!aaa session-id common!!!clock timezone PCTime -5clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00!!!no ip source-route!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 10.1.1.201 10.1.1.254!
[Code] .....
View 2 Replies
View Related
Mar 23, 2012
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
View 3 Replies
View Related
Jan 26, 2012
I have a pptp server on my network and am trying to configure my new RV110W so that I can tunnel through to it from outside.
I believe I must do port forwarding for TCP on port 1723 to get those packets going to my PPTP server. PPTP also uses GRE and I don't see that as an option anyware in port forwarding... Does that just work... as a matter of the VPN pass through checkbox being enabled ?
My netgear router would lock up every few days but it under the firewall configuration it had list of services that included PPTP and I just selected that, entered the IP addresses on the outside that I would accept, and the IP address on the inside that the PPTP clients would connect to, and it worked....
I'm thinking it is harder on this device because this device supports actually logging into it.. I am interested in learning more about that technique especially if it is more secure but the way I see it the firewall device can see all of my network and the pptp server I am using is on a file server and limited to those files shared on that server.
View 3 Replies
View Related
Aug 8, 2012
I Have RV220W Rev 1.0.3.5/I want to create 5 users adn connect remotely to the office network using a PPTP connection.
I have enabled the PPTP server and created users.From a remote location (WAN) on Windows 7, I have created a PPTP connection and I can connect however I can not ping or map to the office network.
View 13 Replies
View Related
Apr 2, 2012
I need a name resolution within my pptp users. How do I configure the dns settings of a pptp user client.
View 4 Replies
View Related
