Cisco Routers :: RV 180W - Connect IPhone / IPad Using PPTP To Home Network?
Jan 31, 2012
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
Being new to the RV180 (and VPN routers for that matter) I have been struggling to get a VPN going, supporting both my Android and iPad devices. However, I understand a IPSEC connection would be a more secure sollution. Unfortunatly I cannot find a clear instruction anywhere to do this.I found the settings/descriptions in the RV180 quite different from the (few) settings in the mobile platforms. So far no success in getting it setup.
I have tried to make a VPN connection between RV180W and iPad with PPTP. I have enabled the server, set the address range, added and user and enabled it.
I entered the same information into iPad but when I try to start the VPN, iPad just tried to make connection and finally fails with an error stating that PPP server cannot be reached.
I think the devices are able to make some kind of connection as if I change the gateway IP address incorrect, I get a different kind of error message. I also tried to reboot the router...
I have a Home network via a Prestige P660 NW - T1 router which has worked fine but I recently bought an IPad 2 with Wifi but I can't connect to my Network with my Password - When I remove the Password and change the router settings to no authentication I can connect but I don't want to have no security on the router.Relatives have tried with their IPads and even though we all carefully put in the Password we cannot access the Network.
How to make a non-client VPN connection to the RVS4000 SBR with an iPhone or iPad? I realize that I could setup some pass-through VPN just fine, but I would like to connect directly to the router and was under the impression from the Cisco product video and other research that IOS was now supported.
I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.I have seen a lot of conflicting information about this so I am looking for a confirmation.
i have issue for Remote App to connect to the Apple TV using the Wireless network setup in my 180W.My wired Mac is able to connect to wireless connected Apple TV but my i phone (4, 4S and i Pad) are not able to connect to apple TV.
Do I have to enable some setting for this to work. It used to work in my very old Buffalo router with tomato firmware.
If I connect the Apple TV to wired network it works fine. Instantly it shows up in i Phone Remote app, but not if its on wireless network.
Is it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
My pc was working fine till I shut it down n restarted it and now it won't connect to the Internet I am running windows vista 32 bit service pack 1 and is wired to my router but I can connect my ipad(which I'm using now) and iPhone through wireless
Does my Belkin F5D8236-4 ver. 1 (firmware 1.00.02) router support Apple's Bonjour print application. I can't get my iPhone or iPad to recognize my new HP Photosmart 7520 wireless printer which is connected to my network through my router.
I recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
I have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
I like to use "URL Blocking" with keywords in the firewall properties. When I activate this feauture, I get errors from the router certificate when I browsing to any site in the Internet. Is there a way to manage this problem without using a public certificate?
Every time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.
I am trying to create a VPN on my Mac that I can access from my iPad in a remote location (work.) I have been using "iVPN" on the Mac to "distribute" the home Mac's Internet connection to the iPad. I have everything set up right and the VPN works fine and the iPad connects fine, just not when I am work, where I want it to work. The iPad tells me that it cannot connect to the VPN. I believe my work blocks VPN ports (1701, 1723 etc) I can do a google search from the iPad on the work WiFi so the connection is ok, but I believe those ports are blocked. If I connect the iPad to a restaurant's wifi for example, the VPN connects fine. What client can I use to create my own VPN at home where I can use a standard port like port 80 or something that is not blocked at work so that I can connect to the VPN from work?
I just setup 3 webcam DSC-930L for a friends with a router DI-655.
I run the setup for the 3 webcams. If I use my dlink on the local network it work, if I used my dlink from let say at work, it work too. If I used the i pad in WiFi it works.
The problem is when I try to use the i phone or the i pad in 3G mode, sometimes it work but most of the time it doesn't, after about 60sec it says something like check your network settings... When I'm able to see something in my dlink app on the i phone, if I return back to the list after that it doesn't work if I switch camera.
Question is, do I have to forward any port on the router in the virtual server section? I'm assuming no since sometime it work and sometimes no. Do I have to activate the UpnP on the router too?
We are implementing a new corporate wireless network with Cisco 5508 WLC's and C3602I LWAP's. We are not running any RADIUS or EAP at the moment and are starting with WPA2 w/ AES with a pre-shared key to begin piloting. The issue we are having is iOS based devices (iPhone/iPad) do not seem to want to connect. We just get a could not join wireless network messages. We have had success with several Windows based laptops, my MacBook connects, as well as several different Android devices.Looking at the logs on the WLC I see these entries which correspond to the MAC address of my iPhone.
*apfMsConnTask_6: Jul 17 17:25:20.620: %APF-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 Could not check supported rates. Missing Supported Rate. Length :0. Mobile MAC: 24:ab:81:92:4d:97.
Currently the ACS 5 is authenticate the iPhone/iPad by using the MAC address (which is entered manually) and AD user/password, i need to do that with certificate, so it will be scalable.
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
I have an ASA5540 running AnyConnect premium (25 users). I know that I need the AnyConnect Mobile license in order to use an AnyConnect client on the IPADs/Iphones. My question is - can I do clientless SSL VPN? Do I need the AnyConnect Mobile license for this?
We're in the process of implementing an ISE 1.1 server for Guest Wireless Access / BYOD at our company and ran into an issue with authenticating from iPhones / iPads when the account is set with 'change password on next logon' (it's a local account created on the ISE server - not AD). It fails and displays 'unable to join network' on the iPhone. The ISE log shows a '5411: No response received in 120 seconds'. We're able to authenticate from Windows devices and are prompted to change the password during the authentication process. If we unchecked the 'change password' box we can authenticate from iPhones & iPads without any issue but we need to have a way for users to set their own password.
IPods and IPads to connect to stand alone AP1131? My scenario is as follows:
There is a section of a campus that is covered by 14 stand alone AP1131 were I experience the problem. The security parameters are: 802.1x, wpa enterprise, tkip
The other section is under WLC also AP1131 but in this case in WLANs/Scurity/Leyer 2 I checked boxes:
Wonder if the fact that I chose WPA2, AES makes a difference with stand alone mode? Anyways I tried configuring AES in stand alone APs and it didn't make a difference since I could not connect either.
I really worked hard not to write this question here but here I am. I am trying to route all traffic through vpn but I cant browse the web. It seems no traffic goes through the vpn tunnel. Split tunneling works but it doesnt route the traffic through vpn tunnel. I have a cisco asa5505 with base license,
When I try to browse the web with one of the clients I see lots of
6Apr 07 201309:40:5510.10.50.136088410.10.10.153Built inbound UDP connection 834 for outside:10.10.50.13/60884 (10.10.50.13/60884) to outside:10.10.10.1/53 (10.10.10.1/53) (xxxx
messages but at the end I see " Safari could not open the page because the server stopped responding" message or smth similar.
We have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
I have an issue with my home network that is really stressing me out now. I have a Thomson TG585 v8 router that my laptop, iPad and iPhone connect to no problem but my iPad/iPhone won't talk to my laptop.. I want to be able to use my iPad to remote in to my laptop to watch movies etc. Network sharing is on the laptop and I've checked that all devices are on the same network..I can't ping the iPad or iPhone from the laptop either.
My iphone wireless connectivity to my Linksys router that I have put up with for a year, but as I now have the same issue with my ipad I've decided enough is enough.The issue is that they both connect OK to the router and therefore to the internet, but after a short period of time (minutes) whilst it appears that they are still connected to the router the connection seems to completely hang. At that point I have to go into settings on the iphone/ipad and turn off the wireless connection and turn it on again. This then allows connectivity and internet activity for 5-10 (15-20) minutes before it hangs again.I have no problems with connecting to any other router from the iphone and ipad. And I also have no problems with my PC's connecting to the Linksys router.
Region : India Model : TD-W8951ND Hardware Version : V4 ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
