D-Link DCS-930L :: IPhone App OK Via Home Network (Mac) / Can't Connect Via Cell Network
Apr 7, 2011
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies
ADVERTISEMENT
May 18, 2012
How do I connect my cell phone to my home network so that I can use the internet on my cell phone
View 7 Replies
View Related
May 6, 2011
I downloaded the MAC setup Utility(BETA) and it can't find the camera.The camera is connected via Ethernet-Light on the front under the lens is green (blinks sometimes)First thing I noticed wrong was the setup utility asks if the light on the side of the camera is lit green-there's no light on the side of the camera as far as I can tell. I tried unplugging the camera and hitting the reset button on the back-nothing works.
PC: MAC OSX 10.6.7 (2.2GHz Intel Core 2 Duo/4GB RAM)
Router: Linksys WRT54G Wireless-G Broadband 2.4GHz
Browser: FireFox 4.0.1
View 3 Replies
View Related
Jan 31, 2012
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
Cisco RV 180W
Firmware Version:1.0.1.9
View 7 Replies
View Related
Oct 17, 2011
Every time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.
View 6 Replies
View Related
Jun 9, 2011
I just setup 3 webcam DSC-930L for a friends with a router DI-655.
I run the setup for the 3 webcams. If I use my dlink on the local network it work, if I used my dlink from let say at work, it work too. If I used the i pad in WiFi it works.
The problem is when I try to use the i phone or the i pad in 3G mode, sometimes it work but most of the time it doesn't, after about 60sec it says something like check your network settings... When I'm able to see something in my dlink app on the i phone, if I return back to the list after that it doesn't work if I switch camera.
Question is, do I have to forward any port on the router in the virtual server section? I'm assuming no since sometime it work and sometimes no. Do I have to activate the UpnP on the router too?
View 1 Replies
View Related
Jan 27, 2013
How to develop an iPhone based application which can show live streaming from DCS-930L IP camera? how to support various other IP cameras as well in the application?
View 8 Replies
View Related
Jun 2, 2011
Currently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.
View 1 Replies
View Related
Nov 5, 2012
LED is solid red (front) and solid blue (rear). try resetting thru the pinhole button but problem still the same. Camera not detected anymore on my network. I've try switching on and off, problem still there.
View 4 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Dec 4, 2012
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies
View Related
Nov 14, 2011
I have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
View 3 Replies
View Related
Apr 5, 2012
My iphone 4s does not connect to my wireless network which runs on netgear wgr614 v7. It did until two weeks ago. On my phone it will not accept the password and I have not been able to connect at all. On my phone it shows the network is locked.
View 4 Replies
View Related
Jun 14, 2011
I log onto other wireless networks the first time by inputting their passwords. My iphone then always automatically reconnects wirelessly to them without have to input the password again. The phone can be asleep for a few minutes or I can be gone for a month. The phone always automatically remembers & reconnects to these networks.However, it doesn't work that way with my d-link system @ home. Everytime the phone sleeps and I wake it up, the wireless connection is lost. There is no automatic reconnection. I have to input the password each time in order to re-establish the wireless link. My printer and laptop seem to stay connected. d-link settings I need to change in order to get my iphone to automatically connect all the time?
View 7 Replies
View Related
Jun 6, 2011
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
View 9 Replies
View Related
Dec 8, 2012
My laptop's wifi is just working fine with TP Link but I'm unable to connect internet via wifi on my iPhone 3G. My iPhone's wifi just works fine in my office. Is there any solution available?
iPhone 3G 8MB
iOS 4.2.1
Modem Firmware: 06.15.00
Router: TP LINK TL-MR3220
Firmware Version: 3.13.12 Build 120524 Rel.60134n
Is there additional setting for iPhone?
View 1 Replies
View Related
Jun 23, 2011
[code] Started laptop and couldn't connect to wireless network, which used to work. I tried "netsh..reset.log" , "netsh.." , Repairing the network connection but still not working.
View 8 Replies
View Related
Jul 19, 2012
I have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies
View Related
Feb 14, 2013
I have 2 questions about a Network hard disk(for home using).I bought a hard disk (with a network card).This hard disk is connected to my "box"I have 2 questions...Is there a way to increase the speed of writing (20 Mo/s in usb) against 1 Mo/s in network.My second question is to find a way to connect to this harddisk from another network without using VPN
View 4 Replies
View Related
Mar 13, 2011
I have a question about my windows systems(XP and Vista) re-connecting to my network folders when my computers restart. I have some shared network folders on my Synology DS410. And then i mapped a network drive to use those folders.But every time i restart my computer i get the message "cannot reconncet all network drives"I have to put in my username and password everytime. I choose Remember login and password.How can i fix this so it automatically connects to these on restart?
FYI...
1 computer - Windows Vista Home Premium
1 computer - Windows XP Home
Both connected via wired LAN
My iSCSI drives connect just fine on restart. Just not my mapped network folders.
View 1 Replies
View Related
Mar 12, 2011
Set up our E3000 following the set-up guide. However, wireless devices (laptop, iPhone) recognize the network, but cannot connect. There's no prompt for a password or anything.
View 6 Replies
View Related
Mar 16, 2011
I have a home network and I need to connect 3 USB printers. I was searching online and I'm not sure if I needed a network switch, a USB network hub, or a multiport print server. I need all 3 PCs to be able to access any printer.
Here's what I have in mind. I'm just not sure what hardware I needed (red outline). The cheaper the better. Oh and I don't want a 24/7 PC running as a server.
View 3 Replies
View Related
Jul 11, 2012
I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
View 4 Replies
View Related
Nov 24, 2011
My Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again
View 3 Replies
View Related
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
View 5 Replies
View Related
Mar 29, 2011
I'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
View 1 Replies
View Related
Apr 7, 2011
I just recently purchased the DCS-930L wireless camera, and I am trying to connect it to my Netgear router but it states that there's an error and can't connect. My itouch and laptop connects fine with the router.
View 6 Replies
View Related
Apr 6, 2011
I would like to connect to the internet on my home wireless network using my cell phone - allowing me to drop my cell phone internet service charges. I'd keep the cell phone agreement for placing and receiving calls, but be able to connect to the internet at home using the home wireless network.
View 2 Replies
View Related
Sep 2, 2012
I seem to be struggling to connect more than 4 cameras to my (ISP-supplied) modem/router by Netgear CGD24N via WPS. I'm on my 5th camera now (already have 3x 930L and 1x 942L) but the newest 942L just won't connect to the network at the moment and there's definitely no faults here as I swapped cameras today at the local retailer (and got an A3 942L!).I've even tried connecting the camera to my wireless extender (Netgear WN3000RP) but no luck there.
So far it has only worked twice for short periods of time (enough for me to configure the cameras) but since then I can't actually get it working. I've got a couple of spare wireless routers lying around too and should be receiving a DIR-600 soon (from the Netgear promotion in Australia) which could be useful?
View 1 Replies
View Related
Jul 22, 2011
I have installed two 930L cameras which work fine via mydlink. When I attempt to connect them to D-View Cam 3.11 they fail to connect or will not stay connected.I first tried connecting to the router with both cameras in the same room as the router. One will connect and stay connected but the other will connect and freeze or not connect at all. If I move th GOOD camera out of the room, it will not connect.Do I have a router issue? I am using Verizon FIOS with their supplied router (Actiontec, I think). My wireless laptop connects but signal strength is never 5 bars.
View 2 Replies
View Related
Nov 12, 2012
I cannot get the camera to connect to our wifi via WPA2-PSK:AES, which is what it runs. The network /SSID is visible in the setup, but it won't connect and get an ip. I see no error messages or any kind of information at all in the admin web page.I've upgraded to firmware 1.05
View 2 Replies
View Related
Jul 23, 2011
My internet speeds are 45 Mbps DL and 1 Mbps UL and my various wireless connections (3 laptops in my household) were achieving speeds anywhere from 25-40 Mbps DL. My router started acting up and wasn't letting anyone connect via wifi so I did a factory reset and set it up the same way I did before (as best as I could), it started working fine again but now the speeds on all the devices that are connecting to at are capped at 18 Mbps. A simple speed test shows that no matter what they won't pass 18 Mbps, I am almost 100% certain this is the router and I was wondering what I might have done wrong or what is causing this.
View 5 Replies
View Related
Aug 1, 2011
I'm getting an error during setup that says "You are unable to connect to the mydlink web site, and your camera could not be added to your mydlink account."
View 14 Replies
View Related
