Home Network :: Advanced Home Network Setup (3 Subnets) And Port Forwarding?
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
I want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
1. a LAN with about 10 pcs, a router and a shared internet connection which is connected to the router.
2. One of the PCs is a server, and is accessed from outside. the port 2230 is forwarded to it in the router.
Now the matter is, as the server uses a shared internet connection which is always very slow,I decided to have a dedicated internet connection in the server by adding an extra NIC.but what happens is when the outsiders try to connect to the dedicated internet connection IP address,the port 2230 is not forwared to the server pc.If I dissable LAN in this PC then the outsiders are able to connect.
I'm struggling to set up an SSH router and it always looks like the port is closed...
Here's my set-up
www>D-Link router (ADSL connection)>Linksys router (+Tomato)>Target PC
I have set up the Linksys router to be an SSH server running Tomato as described in many other forums. The "Tomato router" sits behind my ISP-provided D-link-2680 router.
The internal IP of the Tomato router is 192.168.1.200 and if I try: Code:
I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
I have a home network. There are a total of 3 PCs. Each runs Server 2008 32 bit. One PC - Lets say Server A has 2 NICs with Ip addresses, 10.0.0.10/30, 10.0.0.2/30.Other two computers Server B and Server C have single NIC with addresses 10.0.0.1/30 and 10.0.0.9/30 resp. So as you can see that there are two subnets 10.0.0.2 - 1 and 10.0.0.9 - 10. I can ping B and C from A. I want that B and C can also ping each other and if I run tracert on B or C, it should give me the route to the destination via A. All this without any other hardware. Like using route add... etc eg. if I write tracert 10.0.0.9 on B, it should return a route like 10.0.0.1-----10.0.0.10------10.0.0.9. Refer to the image that I have Attached
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
i'm connected to the internet through a shared internet connection through a switch,and also have 3 computers connected to the same switch,what i want to setup a local network between the 3 computers but separated from the internet network?
I am having problems setting up a network, recently bought a used linksys router and had to restore to default settings. Now I am trying to set it up but I cant go to the ip 192.168... it times out, but when I go online and do the same thing I get a FW-1 at checky: Access denied. error. This is obviously my first time setting up a network using a router. what am I doing wrong? I checked drivers and I have tried plugging the cat5 into both internet and the 1st and 3rd port with little success, either a timed out connection or an error.
I have Infinity so don't know if that's an issue in my situation. I know I'm being "throttled" by BT when doing P2P downloads so limit this to off peak periods.I have made the recommended tweaks to Utorrent to speed things up and finished off today by port forwarding. I tried to follow the tut I was using to the letter but the download became even slower!! You have to enter the port number in the Hub settings but I wasn't sure whether it was a single number xyz or a range 0-xyz or even xyz-xyz. I really hope I'm making sense.I also wasn't sure whether it's TCP or one of the other options I should have selected. I'm currently on Infinity getting 37.4 Mbps download and 1.7 Mbps upload.
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
I have a router supplied by my ISP, Verizon[a g-router] using with 2 desktop and 2 laptop computers. All but 1 laptop are still running XP.So far I have not tried to print over the network. The printer is connected to the desktop that is also wired to the router.how to setup printing across this wireless network. Must I setup another internal home network in order to do wireless printing?
I have a SMC Rogers router and need to extend the range due to dead spots in house. I have purchased a D-Link N300 dir-615 router . can i just hook it to the eathernet lines I have on the second floor to extend range of the wireless network? How do I set it up IP address for best results? concerned that 2 IP addresses would not work at same time??
I'm trying to set up my home network with two routers. One as the LAN router and the other as the access point. I have a really nice router and an older router, I'll just leave it at that. One router will be connected to the modem, the other in my game room for the wireless access point. I want to use the nicer, newer router as the LAN router or the wireless access point?
I am trying to set up a wireless network within my home, i have a external hard drive and was wondering can i connect this to my internet router to make it accessible in order to stream music and movies from the hard drive. there is no ethernet port on the hard drive but seen a usb to ethernet adapter is this all that would be needed?
I want to set laptop 1 at home music receiver location. laptop 1 will be used to play music and play music from web over home stereo. I want to be able to access laptop 1 from other devices, iphone 5, other laptops and have the ability to remotely change the music.Laptop 1 can be connected via network cable or wireless to wireless home modem.
I have an exhibition next saturday on network monitoring and I was given ftp server monitoring project. I'm only allowed to used linux based OS for this project. Right now I have 3 notebook. 1 as a client, 1 as a router and another 1 is for monitoring. Right now, I only can make a connection between the client and monitor notebook by using Freebsd in the router. How to setup a ftp server and how to monitor it?
I am extremely new to network but also excited with the things you can achieve with a Cisco switch.For about 3 months I sat down looking at my "Cisco C2950-24 Switch", this surely for such a beastly looking thing it must be able to do something other than just allow you to plug in cables. So with that said I started to do some reading and watched a couple of You Tube Videos.I am on the route to complete my first goal and thats have my own VLAN setup with 1 Server and 6 clients. The Server is running ESXi therefore a few other servers are running inside it too.So my VLAN - VLANID 20 running the network 172.22.22.0. On the physical switch I have the following:Port 1 - WAN incoming connection from my Router on the network 192.168.178.0Port 2 thru 9 all running on VLAN 20.By the way I am using the GUI Cisco Network assistant
I have this setup at home and I can't make wireless bridging to work with two WR740N routers.I tried 3 online tutorials and none of them worked
R1,R2,R3 = routers The main router "R1" Is setup like this : IP Address 192.168.100.1 DHCP enabled 192.168.100.120 - 192.168.100.150 Gateway 192.168.100.1
I have connected my Vista laptop to my old XP laptop using a network cable so that I can share files, printers, etc freely.I have forgotten the correct proceedure for doing this, although the two computers eventually, after a long time link up and I am able to share files. I have done nothing else. I have not entered numbers or anything. The number spaces are blank.I do not understand why it is working at all, but how do I speed up the connection?
I am just wondering how to set up a home network with an old computer used as a server... we will have a wii, ps3, lap top, and 2 desktops connected to the network as well as two dell printers. The laptop runs windows XP and the desktops run windows vista. The old computer will will use as a server is windows xp or windows 98 (most likely wont use that computer). What will i have to do to set this up and run the server as well as the network.
Cannot setup NAT on edimax router I ve got this setup: [URL] It works well - I can connect from TESTPC and LAPTOP (bottom left corner) to SERVERS A/B/C (bottom right corner) without any problem. Everything seems to be routed perfectly, however from SERVERS A/B/C I cannot ping TESTPC and LAPTOP, and I can't even establish an RDP connection.I was told to setup static routes or NAT, but I am at a loss on how to do it. I am using an EDIMAX BR-6424NL wireless router ?
how to setup a home wifi network with windows 7?I want to access internet of the main laptop (has internet using a dongle)for my other laptop which has no direct internet connection at the moment, but wifi enable.
is it possible to connect the wan port of a cable modem to a lan port of the home network? the reason is, i need some wifi access and more ports to my wired network, and the most reasonable solution would be a cable modem router with wifi and 4 ports just plugged into one of my routers.
I am very newbie to networking. Although I am a newbie I managed to install Windows Server 2003 by following instructions got from Google but have not played around completely. I have 2 PCs with XP, 1 unmanaged switch. If I connect the 3 PCs (2 Xp clients + 1 server) using one unmanaged switch,
1. how do I setup the server to be able to give permanent IP to each PC (clients)?
2 how do I make the 2 PC be able to access the server?
I have a work supplied laptop. Used to be able to connect to my home wireless network - this stopped working last week. It can connect to other wireless networks, both at the office and other public places, but can't connect to my home network.
I've tried: Manually creating the wireless network Removing the profile from regedit Removing the profile from ProgramDataMicrosoftWlansvcsProfiles
It sees the network and attempts to connect, but never successfully connect. I have other laptops at home that are working just fine. The network is setup with WEP security, and I've entered/reentered the password several times.
Note, when I started this, the home network did not appear under the Manage Wireless Networks list in the Network and Sharing Center.
I have a dir-615 D-link router. It is well installed with my main computer that is an old XP windows system. I tried to create a network to give acces to my friend laptop when he comes home(he has a mac). I setuped a network with a name and a password. So my friend could find the network name and i gave him the password, but it never works. Another friend of mine also came with an older iBook laptop and the same thing happens.
