Home Network :: Connecting Different Subnets Without Router?
Apr 12, 2012
I have a home network. There are a total of 3 PCs. Each runs Server 2008 32 bit. One PC - Lets say Server A has 2 NICs with Ip addresses, 10.0.0.10/30, 10.0.0.2/30.Other two computers Server B and Server C have single NIC with addresses 10.0.0.1/30 and 10.0.0.9/30 resp. So as you can see that there are two subnets 10.0.0.2 - 1 and 10.0.0.9 - 10. I can ping B and C from A. I want that B and C can also ping each other and if I run tracert on B or C, it should give me the route to the destination via A. All this without any other hardware. Like using route add... etc eg. if I write tracert 10.0.0.9 on B, it should return a route like 10.0.0.1-----10.0.0.10------10.0.0.9. Refer to the image that I have Attached
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
My Linksys Wireless-N Home Router, having a model no: WRT120N keeps disconnecting and connecting.. what is the best thing I could do to eliminate that?
I'm in university halls, using the university wireless network. The network seems to be a large number of routers all with the same SSID on the same network.Usually my connection is great; but sometimes my computer decides to switch to the router from another flat. A few minutes ago my wireless config utility told me I was connected to the flat 24 router. I am now connection to the flat 26 router. It wouldn't be much of a problem, only it's give or take, around 140 times slower because of how far away it is. Heres a quick comparison of the speeds:ad Connection: (The ping here is very mis-leading, it took several minutes to calculate the ping and several more minutes simply to start the download whereas on the previous test it was instant)Here is one I took in December which shows how bad the ping can get:How do I tell my computer to ignore those other routers with the same SSID? They have different MAC addresses, is there something I can do with that? Windows can't tell the difference, I have to do it through the driver software that came with my Edimax wireless card, it recognises each router seperately but ultimately it always recognises it primarily by it's SSID. Sometimes it sticks to the good one, sometimes it changes every few minutes and I have to manually change it back and it is very frustrating, can't it just ignore the bad connection completely?
I can't login to change any of the router settings and the router doesn't have any ethernet ports for students to use, so I need a solution from the PC end (If I could i'd simply change the SSID to something slightly different so it didn't clash, then there would be no problem). The router is literally right outside my door, but my computer insists on switching to the one 50 metres away instead
Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
I have 24 port switch which is already connected to internet through static IP. Now I want to use a router as a wireless device to use internet. How do I connect router to switch?
I have a high speed wireless DSL router from my ISP (Telus). I use one port off the router to connect directly to my desktop computer. Another port is connected to a switch to which ethernet cables to three other rooms are connected. My problem is that when I connect my Bell PVR (9242) to the 'switched' ethernet cable, I'm apparently not able to get a dynamic ip address, which the Bell unit requires, and can't connect to the network.can I connect another router, in place of the switch, to deliver dynamic IP addresses to whatever I connect to the ports in the other rooms in my house?
I have a Thomson TG585 v7 router which is in bridge mode. I also have a NetGear DGND3300v2 router which I would like to connect to the Thomson (eventually I will purchase a switch and connect another device along with the NetGear). The problem is that the NetGear only has 4 LAN ports and no WAN ports, which I assume you would need to set this up.
I have an AirPort Express set up as my router, and that works fine and is the main network that I use. I also have a Linksys WRT54GL that is wired to a printer.Currently, when I want to print from my computer, I have to manually connect to the Linksys network, which is a pain. I would like to wirelessly connect the Linksys to my main network, so I can print even when connected to my Airport Express.Does that mean that I have to configure the Linksys as an access point? A bridge? Something else? How do I do that?
- these subnets are connected to an IP backbone via wirelles acces points
I would like to physically connect these subnets together so the networks devices in S1 could directly communicate with the devices in S2 and vice versa without going through the backbone.
The obvious solution seems to interconnect these subnets with a router or a switch L3. But I would like to connect these subnets and stay at layer 2.
So, is it possible to connect S1 and S2 with a switch L2 ? If I do that, what is going to happen? Can I create just one subnet S3 from this two subnets when I connect them together and have my two separate subnets back as soon as I disconnect them?
I'm running into an issue with allowing all the PCs to use the one printer connected to devpc. I have a westell 7500 from CenturyLink and a Belkin Wireless G router. This is the layout:
Is there any way to disable router devices from connecting to your network? For example I want people to connect ethernet cables to their laptops, ps3s, pcs, etc but not to routers. How would one go about doing that?
I have 1 Cisco switch 24 ports and 12 computers. The 12 computers are divided in three groups and every group is a different network segment.
question 1: I need that every group has communication with its own set of computers but no communication with the computers on the other segments.If I connect the computers to any port on the switch, can they communicate within its own groups? Can the switch pass the network traffic for all of them?
question 2; What I need to do on the switch to have them to reach the internet?
I have a cisco 2921. I have 2 networks that has its own router
192.168.1.0 network is connected to watchguard firewall 192.168.9.0 network is connected to the cisco 2921 router.
I want to connect the 2 subnet using one of the interface of the cisco router. How I can get this work? It is not connected via vpn tunnel but we want to have LAN speed when accessing resources on both network. Each network is connected to a dell switch.
How two PC's can be connected directly for sharing data and resources? What should i use to connect two or more PC's(switch or hub)? Are patch cord and crossover cable the same thing?
I recently set up a VPN on my home computer. I am wondering if it is possible for me to connect to the internet via the VPN without also being connected to the internet via my home wireless network? Right now, whenever I disconnect from my home wireless network, my connection to the VPN will also cut off. This is a problem because should my connection via the VPN ever be interrupted, my home wireless connection would then "take over" the connection, and the eb sites I'm visiting would then be able to see my real IP address, which makes having a VPN pointless. I'd like to have it so that if my VPN connection is interrupted, I will simply not have internet until the VPN connection comes back.
I have a desktop connected to internet broadband provider by a ADSL router with one extra connection to a landline phone.I have a samsung stv LA46D550 with lan port. i woulike to connect TV to the internet provide so that I can browse in TV.what extra hardware and cables do I require(with specifications).also a diagram how to connect these
my desktop has windows 7
TV LCD TV
of coursse I have connected TV to my desktop through an HDMI connector and can use TV screen as either a CLONE monitor to desktoop lor additional monitor to desktop.is this enoiugh or should I connect broadband ADSL router to TV through a router.I prefere wired connections rather wireless.
How the password is correct, the firmware is updated, it finds the home network but when I press connect it tries a few seconds then says unsuccessful
the unit itself is Pandigital Novel 7" the router is a Dynex Wireless router with : WPA/WPA2Personel(PSK) Encryption is : TKIP +AES 802.11e QoS is on Wireless mode is both g and b Wifi protection has been both on and off trying to connect SSID is correct and broadcasting.
We got the thing so her ha;f blind mom can play a few games, but I need to connect to download then, either that or know how to download them to the computer then transfer them to the Pandigital?
I have 6 computers connected in LAN network. In one of the machines(client_1) i have installed the VMWARE.VMWare and Clinet_1 are talking to each other whereas VMWare and other clients are not getting connected. I tried various solutions from the internet but all in vain...i would like to have vmware as another machine in my LAN with incoming and outgoing connections to access files.
I just installed my new TV by Samsung UA55D6400. it's great. I understand that it can be connected to local home net. it has Wireless LAN Built-in BU no Wireless LAN Adapter Support. What I have to buy and install in order to connect it to the local net and also stream movies to it?
I have a cable wireless router in the ground floor lounge and have set up a home wireless network. In the upstairs study we have two desktop computers connected to the router via the wireless network. I have a laptop computer used around the house and garden which also uses the wireless network.A laser printer and an inkjet printer are both connected to one of the computers in the study via USB and are shared with all computers.This means that the computer with the printers connected must by running if anyone requires prints. Both printers have USB and Ethernet ports – but running a network cable to the router downstairs is impractical.Is there a way of connecting the printers directly to the network and leave them powered up so they can be used by any of the computers. I am hoping that there is some extra hardware that will enable me to do this perhaps via wireless.Or – would it be possible to use mains Powerline Network adaptors – with one adapter connected by Ethernet cable to the router and other adaptors connected by cable to each printer.
What I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
Unlike most DVR's, this particular model has a 4-Channel RJ-45 input (others normally have analog BNC video inputs) this is achieved since the cameras come with video baluns which make use of ethernet (RJ-45) wire.can I have such a set-up without using a DVR, instead I would channel 4 cameras to a wireless router with 4 RJ-45 inputs? From there maybe I could connect it to the internet for remote viewing or to a home network for better streaming / saving video recorded into hard disk?
I'm having issues connecting a HP 9000dn printer to my home network. I have windows 7 x64 with a Belkin wireless router. I have the printer (via a jetdriect 615n driver) connected to my router and the computer will not see the printer. I'm a newbie to networking
I have a computer that was previously connected on-site (hard wired) to a corporate network. I am now attempting to connect it on-site to my home network. While I have a live Internet connection going into the computer, I cannot connect to the Internet. Is there soem sort of setting adjustment that i need to make?
I've got a 2600 that I am wanting to connect to my cable modem. However I don't have the knowledge to get it running. My ISP uses a dynamic IP and I am unable to get it to connect.
ROUTER#show run Building configuration... Current configuration : 685 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec
I split my network into 2 to make it more accessible during peak time and to minimize internet traffic. However by doing this only the first network can access our Network Access Storage, the other network can access it because the two are separated by different router and switch also the supervisor need to see both network at the same time for monitoring purposes..
We live in a large ranch styled house. Conversely, we installed two broadband connection at opposite ends of the home. One cable and one DSL. Reason: Kids share DSL and Parents have the cable all to themselves. We are currently wanting to setup a media server where both networks would have access to a database of media files. It would be in the middle of the house and each network would connect to it wirelesslyI guess first off, is this possible
Just got an HDTV, has a load of fancy internet stuff, but only has a wired connection and I can't put my router in this room, and would rather not have to run a wire up from downstairs.
I'm guessing there is a way of connecting to the wireless on my laptop in this room, connect the laptop to the tv via an ethernet cabe, and bridge the connections or something so that my tv gets the internet from the laptop. That's gotta be possible, no? When I try it tho, the connections bridge, but the tv says "Gateway is not connected, gateway address wrong or unavailable". Using auto IP.
They both have laptops and share data via a flash drive and emails between the two laptops.This is the scenario, They both input data into one excel spreadsheet on laptop 1. Laptop 2 works on data, puts it onto a flash drive then goes to laptop 1 and opens the spreadsheet and enters data from flash drive.My thought is wouldn't it be great if they could use some type of VPN? They could both work from home and access each others computer files, spreadsheet and databases.
I want to create an ad hoc network on my lap and when other users connect to my ad hoc network and open your browser for the first time ... I take a personal website, not to have set in your browser ..