I just installed my new TV by Samsung UA55D6400. it's great. I understand that it can be connected to local home net. it has Wireless LAN Built-in BU no Wireless LAN Adapter Support. What I have to buy and install in order to connect it to the local net and also stream movies to it?
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
I have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
i'm connected to the internet through a shared internet connection through a switch,and also have 3 computers connected to the same switch,what i want to setup a local network between the 3 computers but separated from the internet network?
I have just recently installed a new router for my home and the ethernet connection stopped showing up. It instead said "no connections available". I figured the onboard network adapter gave out because of the orange light it gave off and bought a NetGear GA311 network adapter. I installed it and updated it, but the connection still says there are none available.
We've had an old netbeui network set up for a while now but recently switched over to TCP/IP so my computer (running Windows 7 x64) could connect. The other computers on the network are running Windows 2000 and XP.All the older computers are working, but I still can't get mine to connect. It shows up as "Unidentified Network: Public Network"I really don't know where to go from here. I don't know if it should just pop up automatically or if I am supposed to configure it somehow.
There is a device which is connected to the PC via Lan. I have an exe file which is supposed to get connected to that device and perform some operations. However, the problem is, the exe file tries to connect to the local host ip address 127.0.0.1 and i cant change the ip since it's been coded.So, I'm wondering if i can use the device connection (which already has a different ip like 169....) as a local host connection. So whenever it tries to connect to the loopback 127... it automatically connects to the external device.
I am planning to deploy a "Digital Notice Board system" in my office, which gets feed from web server and display data/stream on LCD Screen. Well i am done with implementing all the interface on server side and its working pretty well with client side computer. But instead of using Client Side Computer, I just want to use LCD and make some network interface of Local Area Network directly with LCD (to save cost/installation/maintenance of a dedicated computer with LCD ).
i purchased vaio with win8. Under network icon, I can not see any other computers in the local network therefore not able to access shares unless i explicitly map the shares which is tedious.
On other computers running win7 and xp, each of them can see each other under network icon.However that is not the case with my laptop running 8. Actually i have seen once or twice all pc-s show up but most of the time, they dont appear.
I read somewhere that following service need to be checked to make sure they are running: upnp, ssdp in services. I checked those and they are all running.
I also enabled "turn on network discovery" under network and sharing->advanced sharing. setting. To make it more complicated there are private and public and all network setting. I enabled all items as follows:
1. Private Turn on network discovery is checked along with Turn on automatic setup of network connected devices Turn on file and printer sharing is selected Allow Windows to manage homegroup connections is selected.
2. Guest or public Turn on network discovery is selected Turn on file and printer sharing is selected.
With these settings I still dont see the local computers and their shares. Do I need to check anything else?
lost wifi access thru local (home) connection. can connect thru public network. my grandma during last visit accidentally changed the network to her laptop. Have tried to reset netgear wnr2000v1 with pin in back. turned off and waited and turned back on again--no success. have tried to set up new network--see the network listed but no internet access available. have modem/router from comcast. My laptop is Acer Aspire 5733 with Lan Broadcom and wireless lan atheros.
I have a local network that I want to connect to a WiFi site. The site is a free service offered to our community by a local ISP. The network uses a wireless router but cable links the two relatively old PCs. They are used for a single inventory-accounting program. One serves as the softwre host. The organization wants episodic Internet access so they can use a software update auto installation service. There are alternative ways to accomplish these updates, but this pathway is the only one acceptable to the organization. Why they reject a simple thumb drive using an out of system download is beyond me, but it seems to be a locked in idea. Oh, the current wireless router cannot accept DD-WRT, but one is available if it can be used if useable.
I restored an old Vista laptop to out-of-the-box state to give to my Dad. This laptop had a wireless connection to the internet and network previously. After the restore, I can't get a connection to the internet, even though my router sees it and it has an ip address. It says Unidentified Network Local Access only, and it doesn't see any of the computers on the network. Sometimes the other computers see it but can't connect, sometimes, the other computers don't see it. I hate Vista.
Stats on Laptop: Toshiba A215-S4747 Atheros AR5007EG
All my other eight devices have an internet connection no problem, but I powered off the modem and router a couple of times with no change. I tried updating the Atheros to the latest driver on Toshiba's website for this model, but it doesn't seem to take. If I uninstall the old drivers, Windows rudely just immediately reinstalls them again. If I just update the driver, and pick the new file, the driver version remains the same as the previous driver. I'm banging my head on the wall with the driver
Ping successful on: 192.168.1.11 (the laptop's IP address) localhost
I began having a problem with streaming 1080p content from my media server to a router, wired to a switch that serves a few devices in my home theater (including a HTPC, my Boxee Box). Every 15 seconds movies have to buffer. After a while, I narrowed it down to the switch, since wiring the Boxee Box straight to the router caused the movies to run perfectly.Logically, I thought the switch was the problem, since I really made no changes on my network/DD-WRTRouter other than running a Minecraft server (which shutting that down made no difference in network performance). I ordered a brand new gigabit switch, same problem. Pinging the BoxeeBox returns 0 packet loss whether it's connected to the switch or router, but movies still play perfectly fine when directly connected to the router. Different cables didn't work.
I thought maybe the other devices on that switch were causing some sort of conflict.changed the BoxeeBox's static IP just in-case, unplugged every other device from the switch so that only the BoxeeBox and Router were connected to the switch. It worked fine! Yay! Tried a different cable, still worked fine. Great, I thought, so the problem was never my switch... plugged the old switch back in, then the problem returned. Ugh. Changed back to my new switch (each time power cycling all of the network devices) and the problem persisted, even with the SAME EXACT setup I just had a few minutes previously that worked fine. Tearing my hair out at this point.Since that moment I still haven't been able to reproduce a perfect stream unless the BoxeeBox is directly connected to the router. This doesn't make ANY sense as I had this setup running perfectly fine since November 2010. I am COMPLETELY out of ideas other than running multiple ethernet wires to that drop or running all the other devices on wireless.
Is there any way to disable router devices from connecting to your network? For example I want people to connect ethernet cables to their laptops, ps3s, pcs, etc but not to routers. How would one go about doing that?
I recently set up a VPN on my home computer. I am wondering if it is possible for me to connect to the internet via the VPN without also being connected to the internet via my home wireless network? Right now, whenever I disconnect from my home wireless network, my connection to the VPN will also cut off. This is a problem because should my connection via the VPN ever be interrupted, my home wireless connection would then "take over" the connection, and the eb sites I'm visiting would then be able to see my real IP address, which makes having a VPN pointless. I'd like to have it so that if my VPN connection is interrupted, I will simply not have internet until the VPN connection comes back.
I have a desktop connected to internet broadband provider by a ADSL router with one extra connection to a landline phone.I have a samsung stv LA46D550 with lan port. i woulike to connect TV to the internet provide so that I can browse in TV.what extra hardware and cables do I require(with specifications).also a diagram how to connect these
my desktop has windows 7
TV LCD TV
of coursse I have connected TV to my desktop through an HDMI connector and can use TV screen as either a CLONE monitor to desktoop lor additional monitor to desktop.is this enoiugh or should I connect broadband ADSL router to TV through a router.I prefere wired connections rather wireless.
How the password is correct, the firmware is updated, it finds the home network but when I press connect it tries a few seconds then says unsuccessful
the unit itself is Pandigital Novel 7" the router is a Dynex Wireless router with : WPA/WPA2Personel(PSK) Encryption is : TKIP +AES 802.11e QoS is on Wireless mode is both g and b Wifi protection has been both on and off trying to connect SSID is correct and broadcasting.
We got the thing so her ha;f blind mom can play a few games, but I need to connect to download then, either that or know how to download them to the computer then transfer them to the Pandigital?
I have 6 computers connected in LAN network. In one of the machines(client_1) i have installed the VMWARE.VMWare and Clinet_1 are talking to each other whereas VMWare and other clients are not getting connected. I tried various solutions from the internet but all in vain...i would like to have vmware as another machine in my LAN with incoming and outgoing connections to access files.
I have a cable wireless router in the ground floor lounge and have set up a home wireless network. In the upstairs study we have two desktop computers connected to the router via the wireless network. I have a laptop computer used around the house and garden which also uses the wireless network.A laser printer and an inkjet printer are both connected to one of the computers in the study via USB and are shared with all computers.This means that the computer with the printers connected must by running if anyone requires prints. Both printers have USB and Ethernet ports – but running a network cable to the router downstairs is impractical.Is there a way of connecting the printers directly to the network and leave them powered up so they can be used by any of the computers. I am hoping that there is some extra hardware that will enable me to do this perhaps via wireless.Or – would it be possible to use mains Powerline Network adaptors – with one adapter connected by Ethernet cable to the router and other adaptors connected by cable to each printer.
I'm in university halls, using the university wireless network. The network seems to be a large number of routers all with the same SSID on the same network.Usually my connection is great; but sometimes my computer decides to switch to the router from another flat. A few minutes ago my wireless config utility told me I was connected to the flat 24 router. I am now connection to the flat 26 router. It wouldn't be much of a problem, only it's give or take, around 140 times slower because of how far away it is. Heres a quick comparison of the speeds:ad Connection: (The ping here is very mis-leading, it took several minutes to calculate the ping and several more minutes simply to start the download whereas on the previous test it was instant)Here is one I took in December which shows how bad the ping can get:How do I tell my computer to ignore those other routers with the same SSID? They have different MAC addresses, is there something I can do with that? Windows can't tell the difference, I have to do it through the driver software that came with my Edimax wireless card, it recognises each router seperately but ultimately it always recognises it primarily by it's SSID. Sometimes it sticks to the good one, sometimes it changes every few minutes and I have to manually change it back and it is very frustrating, can't it just ignore the bad connection completely?
I can't login to change any of the router settings and the router doesn't have any ethernet ports for students to use, so I need a solution from the PC end (If I could i'd simply change the SSID to something slightly different so it didn't clash, then there would be no problem). The router is literally right outside my door, but my computer insists on switching to the one 50 metres away instead
What I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
I have a home network. There are a total of 3 PCs. Each runs Server 2008 32 bit. One PC - Lets say Server A has 2 NICs with Ip addresses, 10.0.0.10/30, 10.0.0.2/30.Other two computers Server B and Server C have single NIC with addresses 10.0.0.1/30 and 10.0.0.9/30 resp. So as you can see that there are two subnets 10.0.0.2 - 1 and 10.0.0.9 - 10. I can ping B and C from A. I want that B and C can also ping each other and if I run tracert on B or C, it should give me the route to the destination via A. All this without any other hardware. Like using route add... etc eg. if I write tracert 10.0.0.9 on B, it should return a route like 10.0.0.1-----10.0.0.10------10.0.0.9. Refer to the image that I have Attached
Unlike most DVR's, this particular model has a 4-Channel RJ-45 input (others normally have analog BNC video inputs) this is achieved since the cameras come with video baluns which make use of ethernet (RJ-45) wire.can I have such a set-up without using a DVR, instead I would channel 4 cameras to a wireless router with 4 RJ-45 inputs? From there maybe I could connect it to the internet for remote viewing or to a home network for better streaming / saving video recorded into hard disk?
I'm having issues connecting a HP 9000dn printer to my home network. I have windows 7 x64 with a Belkin wireless router. I have the printer (via a jetdriect 615n driver) connected to my router and the computer will not see the printer. I'm a newbie to networking
I have a computer that was previously connected on-site (hard wired) to a corporate network. I am now attempting to connect it on-site to my home network. While I have a live Internet connection going into the computer, I cannot connect to the Internet. Is there soem sort of setting adjustment that i need to make?
I split my network into 2 to make it more accessible during peak time and to minimize internet traffic. However by doing this only the first network can access our Network Access Storage, the other network can access it because the two are separated by different router and switch also the supervisor need to see both network at the same time for monitoring purposes..
I connect to my corporate network using Cisco AnyConnect Secure Mobility Client. Once connected I can no longer print to my LAN attached printer and other local resources. I use the Cisco/Lyncsys E4200 router on my LAN and can re-connect to the storage on the local LAN by setting up Port Forwarding of port 21 and MS Windows FTP folder sharing. However, I can't seem to connect to a Terminal Services client by forwarding port 3389. Is there a way to connect to the local LAN after logging into the VPN connection. I can connect to regular HTTP/HTTPS sites and most other type of connectiins, just not my own local resources.