is it possible to connect the wan port of a cable modem to a lan port of the home network? the reason is, i need some wifi access and more ports to my wired network, and the most reasonable solution would be a cable modem router with wifi and 4 ports just plugged into one of my routers.
View 2 RepliesI want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
View 1 Replies View Relatedprocedures to connect RJ45 port to the network cable
View 1 Replies View RelatedOur small business just moved into a new building and I am in charge of setting up the network infrastructure. I am not new to computers or networking but I have never had to deal with this set up before.
Our current set up.We have a cable modem from comcast that has the Coax cable connected to it.The modem has 4 ports on it. The ports are connected to a built in 24 port switch that was already in the building. The switch has it's ports connected to outlets in the walls. Currently we have 4 computers on our network and since the cable modem had 4 ports it worked fine.
What we need? We will have another person join our office so I will need to activate one additional port on the switch that already exists. However, since all 4 ports on the modem are already taken, I have no way to add an additional port. They also want us to get wifi in the building.How I think I have to solve the problem (most likely wrong).I have to get another switch (like 8 port) and connect the cable modem to the switch using a cross over cable (if there is no designated internet port). Since I have the modem connected to the switch, I will have to move the 3 remaining connections to the switch.
Then I connect the 4 remaining ports on the switch to the existing 24-port switch that is already there. I will use one of the outlets in the building to connect an AP for Wi-Fi for better signal. Currently the modem and switches are hidden in a closet away from the office space and would mess up the signal.
I was working with Motorola SB6120 cable modem regarding an odd power cycle issue (it would power cycle randomly for 24 hours). While trying to diag the issue, I was taking a peak in his router config and found a port set to forward as:
Application: Comcast
Port From: 888
Protocol: Both
IP: 192.168.100.1
Port To: 80
I understand that his modem admin page is now available from the internet. He said his friend set this up to "modem", but I don't see any advantage of having this done. At this point what are the other advantages of forwarding such ports?Another key note: When the port forwarding was disabled, suddenly the power cycle issues stopped.
I have got a Linksys @ Home HG200 V2 G Gateway. I am trying to setup port fowarding but its not working. I have gone onto the routers port forwarding setup page filled it out but the port is still closed.
View 4 Replies View RelatedI have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
I want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
View 4 Replies View RelatedI am looking to permanently reset the default remote management port of the MODEM DPC3825 to something other than 8080. how to PERMANENTLY change the port from 8080? In the web interface under administration I have several times set it to something else other than the defaulted 8080 but when the modem is rebooted or reset, it goes back to the default 8080.
View 4 Replies View RelatedI'm currently using Cisco EPC 3000 cable modem and Airlive wt-2400r router. Afaik the cisco isn't a router, but i'm still having some weird problems with forwarding and apparently even DMZ wont work .
View 10 Replies View RelatedLately I've been experiencing connection problems between my router and cable modem. Every night after 11:00 PM EST, my Internet connection sporadically goes out. I called my ISP who said there was nothing wrong on their end. Plugging directly into my modem allows me to access the Internet. When I wake up in the morning, the connection is back until 11 or later again. I ran WireShark but I'm not sure what to be looking for. There are a lot of random things from the LLMNR protocol like standard query A zmtvrjaql.
View 2 Replies View Relatedi have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.
View 1 Replies View RelatedI have a home server running CentOS 5 and is accessible over SSH (port 22).When I am at work I am behind a firewall that blocks all ports except the ones needed. So port 22 is blocked to the outside world.Is there a way for me to get an SSH connection to my server? (ie: SSH tunneling or so?)by the way, websites with advanced web based SSH javascript(s) such as serFISH are blocked as well.
View 7 Replies View RelatedI want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
View 2 Replies View RelatedI have tried to open port 25565. Everything in my router is set as it should be,according to the guides I've followed.
View 3 Replies View Relatedso i have a server running on the network on 192.168.0.2 gatewway of 192.168.0.1. I am trying to setup a DVR for remote access and all this was working previously. I have setup the server for a VPN server and remote access, DHCP and ROUTER services are not enabled on the server, neither is NAT. This was working previously, now when i try forward port 8016, and connect, it will not open.
View 5 Replies View RelatedSo I am contemplating the setup for the network in my new home, how to connect 24+ ethernet ports in the house to a single network. I was thinking of getting a nice dual-band wireless router, but those usually only come with 4 or so lan ports. How would I then utilize a large 24- or 48-port switch to connect everything to the router?
View 2 Replies View RelatedI have a lynksys Router WAG325N Wireless+ADSL2 .... It was working fine till last week.. Now its not working, When I reset I can connect through wireless on IP 192.168.1.1... But I cannot connect with lan port(checked with all the ports).. Even its not pinging...My system firewall is turned OFF... I am using a straight Cable.. I Updated the firmware.. but same result.. I dont know more about configurations.. Is it hardware issue or configurations?..
View 1 Replies View RelatedCan i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies View Relatedwondering if redirection or conversion port 8080 into port 80 is possible? if so how and what cisco equipment can do that?
View 11 Replies View RelatedI have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
In my router I can set rule that all traffic incoming to router's extAddr:8888, is forwarded to my intAddr:8888. But I also need reverse rule that packets originating from intAddr:8888 are translated to extAddr:8888. Can I do that? What technique can I search on google to find more information, because it is not port forwarding. I would calll it reverse port forwarding or static port address translation, but I do not find anything useful in internet searching these keywords.
View 3 Replies View Related1. a LAN with about 10 pcs, a router and a shared internet connection which is connected to the router.
2. One of the PCs is a server, and is accessed from outside. the port 2230 is forwarded to it in the router.
Now the matter is, as the server uses a shared internet connection which is always very slow,I decided to have a dedicated internet connection in the server by adding an extra NIC.but what happens is when the outsiders try to connect to the dedicated internet connection IP address,the port 2230 is not forwared to the server pc.If I dissable LAN in this PC then the outsiders are able to connect.
I'm struggling to set up an SSH router and it always looks like the port is closed...
Here's my set-up
www>D-Link router (ADSL connection)>Linksys router (+Tomato)>Target PC
I have set up the Linksys router to be an SSH server running Tomato as described in many other forums. The "Tomato router" sits behind my ISP-provided D-link-2680 router.
The internal IP of the Tomato router is 192.168.1.200 and if I try: Code:
I am trying to connect two D-link 24 port switches thru cat 6 cable, distance is less than 50 meters, but its not working but if i connecting it with a Laptop i am able to connect to the network. But if i connect the switch in between it fails i tried changing the switch and cable but no use anyone have a clue how it fails?
View 4 Replies View RelatedI have a LAN port cable, and I have one end connected to the back of my router.Where does the other end go, so I can receive wireless internet connection of both my Toshiba Satellite Laptop, and Gateway Desktop. First I had the LAN port cable connected at the back of my router, and the other end was connected at the back of my desktop. A little green light lit up at the back of my desktop, saying that it was grabbing signal. I could use the internet fine, and my laptop could grab wireless signal fine as well. I was missing around my router, trying to see what mark it was, and the LAN port cable came off, and when I plugged it back in, i couldn't receive signal, and neither could my laptop. Now the only way I can grab signal is by connecting the WAN port cable from my modem to my desktop, which means I cant get wireless signal on my laptop. Now when I do connect my LAN port cable to the back of my desktop, I try connecting to my wireless connection, and when I go to Network and Sharing Center, it says Connected (With full bars).
View 1 Replies View Relatedcan i connect 2 hard disk to usb port of my WAG320N or one hard disk and one printer?
View 1 Replies View RelatedThe problems looks like this: I'm able to browse the web without any problems until at random points of time - might be 2 hours after I turn on my PC or 5 or even half an hour the port 80 gets blocked - actually more like it hangs it self. As whatever I try to open i get "waiting for response" going and going. It's not even returning "page not found" error or anything. To top everything all other ports work fine - i can use https, ping run tracert - no problem there.
I've spend two days looking for some answer on the web but came up empty. I've scanned for malicious software with ad-awar and malwarebyte anit-malware - nothing came up. After restart of the pc everything comes back to normal but its frustrating needing to do that every now and then.
My home network looks like this: I have some broadband modem that is connected to local wifi TP-LINK router (Model No. TL-WR340G/TL-WR340GD). There are four devices using this connection - two pc's (laptops), android phone and android tablet.
I have a Dell Laptop Latitude 610 and I have not been able to connect to the Internet via the ethernet cable port for some four months now. I've tried downloading software from Dell's web site, I bought (and returned) and USB to Ethernet cable, only to find out that it was a model ahead of what this machine needs.I've asked local repair place (Microcenter) what it might be, but they'll only tell me after I pay $70 just to open it up.Another repair guy said that it is probably the motherboard and it wasn't worth fixing. (Yet if it was, wouldn't the entire computer decide not to work at all?) [code]
View 3 Replies View RelatedHow to connect laptop with a home network without using a cable??
View 1 Replies View RelatedI have Zyxel Modem configured in bridged mode with static IP from ISP. I want to connect multiple PCs to modem via switch so that each PC use the same configured Public IP address to use the internet. For this (generally) I would need to configure NAT for that IP. But I want to know that will it work under bridged mode or not?
View 8 Replies View RelatedI'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.
View 3 Replies View RelatedI'm trying to connect my two computer (XP and Win 7) using a crossover cable. I set the the IP as 192.168.0.1 and 192.168.0.2.The computers can see each each other and I can access the public folder of the win7-machine on my XP-machine. However, if I try accessing the xp-machine it says:
View 2 Replies View Related