I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
View 1 RepliesI have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
I want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
View 2 Replies View Related1. a LAN with about 10 pcs, a router and a shared internet connection which is connected to the router.
2. One of the PCs is a server, and is accessed from outside. the port 2230 is forwarded to it in the router.
Now the matter is, as the server uses a shared internet connection which is always very slow,I decided to have a dedicated internet connection in the server by adding an extra NIC.but what happens is when the outsiders try to connect to the dedicated internet connection IP address,the port 2230 is not forwared to the server pc.If I dissable LAN in this PC then the outsiders are able to connect.
I'm struggling to set up an SSH router and it always looks like the port is closed...
Here's my set-up
www>D-Link router (ADSL connection)>Linksys router (+Tomato)>Target PC
I have set up the Linksys router to be an SSH server running Tomato as described in many other forums. The "Tomato router" sits behind my ISP-provided D-link-2680 router.
The internal IP of the Tomato router is 192.168.1.200 and if I try: Code:
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI have Infinity so don't know if that's an issue in my situation. I know I'm being "throttled" by BT when doing P2P downloads so limit this to off peak periods.I have made the recommended tweaks to Utorrent to speed things up and finished off today by port forwarding. I tried to follow the tut I was using to the letter but the download became even slower!! You have to enter the port number in the Hub settings but I wasn't sure whether it was a single number xyz or a range 0-xyz or even xyz-xyz. I really hope I'm making sense.I also wasn't sure whether it's TCP or one of the other options I should have selected. I'm currently on Infinity getting 37.4 Mbps download and 1.7 Mbps upload.
View 8 Replies View Relatedis it possible to connect the wan port of a cable modem to a lan port of the home network? the reason is, i need some wifi access and more ports to my wired network, and the most reasonable solution would be a cable modem router with wifi and 4 ports just plugged into one of my routers.
View 2 Replies View RelatedI have got a Linksys @ Home HG200 V2 G Gateway. I am trying to setup port fowarding but its not working. I have gone onto the routers port forwarding setup page filled it out but the port is still closed.
View 4 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI have a DSL-524B from D-Link. My problem is, whenever I Port Forward port 80 to my comp's IP to host a web server, all the other computers connected to the router are unable to access the Internet. So, I set up no-ip to use port 8080, but, this exposes my ip and even when masking, if you look at the HTML code, you get the ip.I need to know how to open up port 80 without restricting Internet access to only my comp, or any other work around.
View 7 Replies View RelatedI have a WRVS4400n and a CentOS server that I need to enable a SSH access to from WAN. I created a single port forward rule to open port 22 and forward to server (which address is 192.168.41.3) However ssh connect doesn't happen, the command "ssh user@{external_IP}" times out after 20 seconds. If I connect my server directly to modem through outside interface - I have no problems connecting to it. Once it's behind router - no luck. I even added same rule for UDP, not sure if it's needed, but it definitely didn't hepl. The router is on firmware version 2.0.1.3, version on a bottom is 2.
View 4 Replies View RelatedI've been trying to configure my router which is linksys E1000 to forward port to my sharepoint server. Here is what I have done so far, setup single portforward to i.e 192.168.xx.xx using port 4848.Now my question is, do I need to configure sharepoint to receive this incoming connection. I do need to have my sharepoint be accessed anywhere on the web.
View 1 Replies View RelatedI need to forward port 55443 to an internal address ( lets call it 15.15.15.15) from two outside ip's ( 5.5.5.5 and 6.6.6.6)These addresses need to see the server IP address (15.15.15.15) only and nothing else. It is an ASA 5510?
View 9 Replies View RelatedI have found numerous posts discussing this but have yet to find a solution. I have an RV082 with firmware 2.0.0. 2.0.0.19-tm and I need a way to limit the incoming smtp traffic to just the spam filtering company.I have a port forwarding rule to forward WAN1 port 25 traffic to 192.168.1.10.I tried to add an access rule to deny all port 25 and then added one to allow WAN1 port 25 source <spam company> destination 192.168.1.10The RV082 log screen shows the traffic allowed but it does not work. If I uncheck the 'enable' box on the DENY port 25 rule email is still blocked. Only when I uncheck the 'enable' box on the ALLOW rule does email start flowing again.
View 10 Replies View RelatedI am trying to make my WampServer public but nothing i have tried so far seems to be working. It was all good and well before i got a new router from my new provider.
The router is a Huawei HG523a & my ISP is TALKTALK.
These are the settings i have for the port forwarding. Advanced->Advanced->NAT->Port Mapping
Mapping Name: WebServer(HTTP)
Interface: nas_0_38
Protocol: TCP
Remote Host:
External Start Port: 80
External end Port: 80
Internal Port: 80
Internal Host: 192.168.1.2
Enable: Enable
I have reserved the IP address 192.168.1.2 for my computer under Advanced->Basic->LAN->(Ip address Reserve).
I believe this is all i need to do for the router side of things.
Now for Apache: The .httpd file...
Listen 192.168.1.2:80
And that's everything. The problem is that when i put in my public IP address its not forwarding to my WampServer. its just going to the routers log-in page. If i put in my local ip then i get my servers webpage like i should.
I recently purchased an Asus RT-N12B1. It has an external hardware switch which allows the router to operate in different modes. I put in access point mode. Then I connected an ethernet cable from a LAN port on my Verizon supplied Actiontec MI424WR-GEN2 E router to a LAN port on the access point and turned off the wireless in the router.
I have dynamic DNS setup and port forwarding setup in the router to forward from port 50000 to 192.168.1.2:22 which is a server plugged into a LAN port on the router. This is no longer working since adding the AP and disabling wireless on the primary router. how to debug?
I have set up port forwarding for my WD Network HDD, which runs a Media Server (Twonky). Now, I have tested the ports and accessed it through the internet and it works fine, until... I click a link to open a folder and suddenly I get a "No such page" error thing. I have however identified this problem, it seems that when I go off the main page it re-routes to the original network address, not my IP forward address. For Example if my IP was 82.9.12.456 and the port was 800 i would go to "82.9.12.456:800" and it would load but once I navigate i go to "192.168.0.*:800/*****" and does not load the page. If i then copy and past my IP into the URL it works, but this is annoying.
View 3 Replies View RelatedI am wanting to access my IP camera over the Internet. I am not a computer wiz by any stretch and after a couple of failed attempts. My ISP is Comcast and they say that I have dynamic dns and should have no issues viewing my cameras. I know how to get to the port forwarding area of the router but am confused as to which ports to forward. The set up instructions for the camera (Airsight) suck. Screen shots of the set up don't match the actual router
View 7 Replies View RelatedI have recently purchased an EA4500 router. I assigned my sons XBOX a static IP via DHCP reservation (outside of the standard DHCP range). I set up single port forwarding on all the standard xbox required ports. Once I click the "enabled" box, I am unable to access the internet from any of the computers connected to the router. If I uncheck the enable box, I am instantly able to access the internet.
View 4 Replies View RelatedI recently opened the ports used by Xbox Live: Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP)I am able to use xbox live once these ports are opened but once they are enabled, I can not get wireless internet. The xbox is connected to the router with a cable so it isn't experiencing this probem. My laptop and phone are able to identify the network and join but there is no internet access.
If I disable these ports, everything goes back to normal.
This is my second post today trying to fix the NAT types for my 2 xbox 360. I tried the port forwarding method but with this router when I enable the ports I lost internet access in my wired devices but my wireless devices still have internet access. I even lost internet access on my computer. I never had manu problems with a router trying to get my NAT type open on my 2 xbox.
View 6 Replies View RelatedI would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0.0.0/24) How can I forward different ports to this 3 different private networks with an E2500.Under "Games&Applications" in the" Portforwarding" menu the first 3 octets of the "to IP-address" are fix and corresponds ever with the LAN ip address of th E2500.
View 4 Replies View RelatedI would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0. 0.0/24)How can I forward different ports to this 3 different private networks with an E2500.In the "Games&Applications" Menu are the first 3 octets of the "to IP-address" are fix and corresponds with the LAN ip address.
View 3 Replies View RelatedI have a home server running CentOS 5 and is accessible over SSH (port 22).When I am at work I am behind a firewall that blocks all ports except the ones needed. So port 22 is blocked to the outside world.Is there a way for me to get an SSH connection to my server? (ie: SSH tunneling or so?)by the way, websites with advanced web based SSH javascript(s) such as serFISH are blocked as well.
View 7 Replies View RelatedI have tried to open port 25565. Everything in my router is set as it should be,according to the guides I've followed.
View 3 Replies View Relatedso i have a server running on the network on 192.168.0.2 gatewway of 192.168.0.1. I am trying to setup a DVR for remote access and all this was working previously. I have setup the server for a VPN server and remote access, DHCP and ROUTER services are not enabled on the server, neither is NAT. This was working previously, now when i try forward port 8016, and connect, it will not open.
View 5 Replies View Related