I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
when opening SSH service to a Database Administrator within my LAN, that has a RV016 as the default gateway. So confidence, I just set up a port forwarding in Setup > Forwarding and everything works fine, cool.
However, I do not want this to be a public access, I need a specific firewall rule for a specific external IP address (only the DBA fixed IP Internet might connect to my database server through SSH).
O noticed that when a port forwarding is created within RV016, it bypass the firewall default rules and wide-opens the service (port) to the web. Conceptually, this is correct, as port forwarding is a network translation, but I expected that my firewall had work over this.
My current solution was to create a "Deny from all" rule at port 22 and then create one additional rule that allows traffic from an specific IP at port 22.
have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.All this box really does is port forward external clients to 1 address on the internal lan for client software updates.So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
I am trying to forward specific ports from the outside interface on my ASA5505 to my servers inside and can not get it to work! I have a VPN that currently works and the firewall rule in place I am just overlooking something simple I'm sure. Here is the config:
We are trying to setup our ASA 5505 to do port forwarding to multiple internal servers and have run into some issues. A little background on what we are trying to do.
We have 1 static external IP. Internally we have one exsisting server (10.1.1.184) that has port 80 forwarded to it and another exsisting server (10.1.1.185) that has port 443 forwarded to it. Both of these servers are serving seperate web apps to our employees who of course use them offsite. We have now added an additional server (10.1.1.186) that needs to use both ports 80 and 443. Is there any way to set it up so that these ports can be forwarded to all the servers that need them? Also, how would this work as far knowing what traffic will need to go to which server even though it is using the same port?
The equipment is: ASA 5505ASA Version 7.2(4)ASDM Version 5.2(4) I appologize in advance if what I'm trying to do is difficult/impossible. I inherted the ASA 5505 at this location and I was not here when it was initially installed. In fact no one on staff was here when it was initially installed. I did manage to find the passwords to it though. I'm not at all familiar with the ASA 5505 or Cisco secuirty appliances in general.
I have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
I have Cisco ASA 5505 Firewall with security plus license, Currently I open ports on 25,80,443 on public IP address 1.1.1.1 and perform static nat between the inside and outside IP address Such as i configured via CLI
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 80 access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 443 access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 25
The outside interface on the ASA is on DHCP. I have a single dynamic public IP from my ISP. The inside interface provides Internet access for the network using NAT.
I have a server on the internal network with an IP of 192.168.0.6 and I would like to access this via SSH (TCP port 22) from outside.
I've been able to do this in the past on a PIX with a static public IP block, but I'm new to ASA and I don't know how to do it with PAT.
Current running config attached for what it's worth, but it's pretty basic at the moment.
Doing a port forward for remote desktop with asa 5505 9.1.1 and asdm 7.1.1 I could have done this with the previous versions of asdm but now it even more confusing?
Here is my environment: DSL Modem - ASA 5505 - switch ,Inside network (192.168.2.0/24)
What I have successfully done: - Modem online and passing on DHCP requests from the ASA to my ISP (ASA does get an internet address on the outside interface) - ASA assigning DHCP to internal network - All internal clients can access the internet.
What I am getting stuck on is getting NAT rules set up for simple port forwarding. What I would like: ANY internet address be able to access a server on the inside network address (192.168.2.x) over tcp/22 . I set up what I believe to be the correct NAT rule and Access Rule, but the packet tracer fails. Here is my config.
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
With the Cisco ASA-5505, is there a more secure port that can be configured for VNC other than 5901? I am new to Firewalls We have a User who has requested that 5901 be opened but I was advised not to do so for security concerns.
I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..
I would like to be able to do SSH port forwarding from outside to an IP address inside. Normally, this is very straighforward.
The problem now is that if I do so, then the LAN to LAN VPN stops working!.There is a LAN to LAN VPN working flawlesly (so far) between an ASA 5505 and a Cisco 861 Integrated Router. However, I would like also, to give SSH access to an IP address behind the Cisco router. The moment I do this the VPN breaks!
I attached the Cisco 861 router configuration, where the problem shows. The ASA has public IP X.X.X.105 and the router has X.X.X.105. These two are used for the VPN tunnel.
The internal network in the ASA is 10.115.16.0/24 and 192.168.10.0/24 in the router. These talk to each other using the tunnelt. But, the moment I try to forward port 22 in the router from X.X.X.107 to 192.168.10.30 the VPN breaks! I do that with the following line: ip nat inside source static tcp 192.168.10.30 22 X.X.X.107 22.Obviously, something is eluding me. The configuration is rather short and simple. But, I'm a newbie with Cisco rotuer configuration. Note that the tunnel stays up after I use the natting entry and I can talk from the router to the ASA, but not the other way around!The router is Cisco 861 with IOS version 15.0(1)M7.
So currently I'm having issues with changing my nat type to open for my ps3. I've tried to use DMZ and port forwarding to change the nat type, but sadly I couldn't get this to work. Most the guides on the forums are for xbox's which wouldn't work for a ps3. Any handy guide to change my nat type to open for my ps3?
We have an ASA 5505 and I need to set up port forwarding for an unusual port number which will be used for FTP on an IIS server.It's a bit complex as there are 3 VLANs: these are called ISP, Server and LAN-side VPN. We need to add a TCP port 8521 forward from the server's IP in Server WAN to ISP WAN VLAN with public IP address.
We are trying to install filter software at our main location and branches. The admin console has been installed at the main branch, but I need to allow access to ports 58000-58003 through our firewall in order to successfully install the software at our branches.
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
I have a Cisco home rack lab which is behind my ASA 5505. I use my ASA to connect to the internet. My situation is I travel a lot for work, and I am unable to do my labbing practice. I am pretty new to ASA and would like to do a port forwarding to access my access server which is connected to my Cisco routers and switches.My network topology is this: (internet)-------(ASA 5505)----------(3550)-------(CM32 Access Server)----------(Cisco Rack) This is how I setup my remote access:
just getting started with ASA's. I've got my 5505 almost 100% configured but my port 25 forward to my Exchange server. Currently I've got an access list forwarding all traffic that hits the outside interface on port 25 to my Exchange server (access-list outside-in extended permit tcp any object mail-port-25 eq smtp). What I'd like to do now is say that only port 25 traffic from specific IP subnets gets forwarded. I thought I read that there's a couple of way to do this (from the inside interface, from the outside interface).
Also, what happens to port 25 hits that don't fall within the range I specify? Do they get a disconnect reply or do they just get ignored (no reply whatsoever)?
Edit: ...just to clarify, the allowed IP's I will be entering are the WAN IP's of my AS/AV service.
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
Region : UnitedKingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
