Cisco Firewall :: ASA 5505 Set Up Port Forwarding For Inbound SSH?
May 12, 2011
how to set up port forwarding for inbound SSH?
The outside interface on the ASA is on DHCP. I have a single dynamic public IP from my ISP. The inside interface provides Internet access for the network using NAT.
I have a server on the internal network with an IP of 192.168.0.6 and I would like to access this via SSH (TCP port 22) from outside.
I've been able to do this in the past on a PIX with a static public IP block, but I'm new to ASA and I don't know how to do it with PAT.
Current running config attached for what it's worth, but it's pretty basic at the moment.
View 3 Replies
ADVERTISEMENT
Dec 2, 2011
So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
View 28 Replies
View Related
Dec 15, 2011
I have a non-cisco router with a public WAN address. This is conencted to a 3750 switch internally. The switch is the default gateway for all VLANs, and the gateway router has static routes back to the 3750. The Router provides NAT, no NAT is done on the switch.My requirement is to port forward port 29 000 so that I can access a server on VLAN4 via this port.
So, I have: Router: Port 29000 map to 192.168.4.1 (Switch VLAN4 address)
The question is, how do I route port 29000 from the 3750 to the server on 192.168.4.42 ? what exactly I should add in order to port forward port 29000 incoming form my router, to my server on 192.168.4.42.
View 17 Replies
View Related
Feb 25, 2013
have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.All this box really does is port forward external clients to 1 address on the internal lan for client software updates.So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 16 Replies
View Related
Dec 6, 2012
I have ASA5505 and am having issue with port forwarding NAT . [code]
View 11 Replies
View Related
Sep 1, 2012
I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox (moderate NAT).
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).
[code]
# sh run
: Saved
:
[Code].....
View 3 Replies
View Related
Oct 1, 2012
I am trying to forward specific ports from the outside interface on my ASA5505 to my servers inside and can not get it to work! I have a VPN that currently works and the firewall rule in place I am just overlooking something simple I'm sure. Here is the config:
ASA Version 8.2(5)
!
hostname ASA
enable password <removed>
passwd <removed>
[Code]...
View 16 Replies
View Related
Mar 15, 2012
We are trying to setup our ASA 5505 to do port forwarding to multiple internal servers and have run into some issues. A little background on what we are trying to do.
We have 1 static external IP. Internally we have one exsisting server (10.1.1.184) that has port 80 forwarded to it and another exsisting server (10.1.1.185) that has port 443 forwarded to it. Both of these servers are serving seperate web apps to our employees who of course use them offsite. We have now added an additional server (10.1.1.186) that needs to use both ports 80 and 443. Is there any way to set it up so that these ports can be forwarded to all the servers that need them? Also, how would this work as far knowing what traffic will need to go to which server even though it is using the same port?
The equipment is: ASA 5505ASA Version 7.2(4)ASDM Version 5.2(4) I appologize in advance if what I'm trying to do is difficult/impossible. I inherted the ASA 5505 at this location and I was not here when it was initially installed. In fact no one on staff was here when it was initially installed. I did manage to find the passwords to it though. I'm not at all familiar with the ASA 5505 or Cisco secuirty appliances in general.
View 19 Replies
View Related
May 20, 2012
I have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies
View Related
Dec 27, 2011
I have Cisco ASA 5505 Firewall with security plus license, Currently I open ports on 25,80,443 on public IP address 1.1.1.1 and perform static nat between the inside and outside IP address Such as i configured via CLI
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 80
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 443
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 25
[Code]......
View 1 Replies
View Related
Dec 16, 2012
Doing a port forward for remote desktop with asa 5505 9.1.1 and asdm 7.1.1 I could have done this with the previous versions of asdm but now it even more confusing?
View 21 Replies
View Related
Jun 26, 2012
I am trying to port forwarding Exchange 2010 OWA using ASA5505, wherever I used object NAT or Twice NAT it just doesn't work.... here is my config:
access-list outside-access remark "Exchange Server Access Rules"
access-list outside-access extended permit tcp any host <public x.x.x.11> eq smtp
access-list outside-access extended permit tcp any host <public x.x.x.11> eq https
[code]...
note that i use public ip <public x.x.x.9> on the outside interface for PAT, so all hosts in the same private can access internet
View 1 Replies
View Related
Jan 15, 2013
Here is my environment: DSL Modem - ASA 5505 - switch ,Inside network (192.168.2.0/24)
What I have successfully done:
- Modem online and passing on DHCP requests from the ASA to my ISP (ASA does get an internet address on the outside interface)
- ASA assigning DHCP to internal network
- All internal clients can access the internet.
What I am getting stuck on is getting NAT rules set up for simple port forwarding. What I would like: ANY internet address be able to access a server on the inside network address (192.168.2.x) over tcp/22 . I set up what I believe to be the correct NAT rule and Access Rule, but the packet tracer fails. Here is my config.
ASA Version 9.1(1)
hostname xxxxxx
domain-name ugh
enable password xxxxx encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[code]......
View 6 Replies
View Related
Oct 6, 2011
I configured an ASA 5505 a couple of weeks ago. Every thing is working properly except it sends irritating messages to the syslog server. Her is an example of the message:
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/252 flags PSH ACK on interface outside
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/2252 flags ACK on interface outside.
View 1 Replies
View Related
May 31, 2011
Last night I switched out our old Cisco pix 515 with a asa 5505. The config is the same and internet and outgoing mail is working but no mail is coming in. Below is a copy of my config. Why my inbound mail is not coming in.
smtp 192.168.51.248 (Barracuda email filter)pop3 192.168.50.11 (exchange server). Tried to telnet into the firewall but connection timed out. Went to mxtool box and that also timed out while trying to connect to smtp. Port scan from mxtool box timed out too on all ports.
[Code] ........
View 5 Replies
View Related
Nov 22, 2012
I have upgraded an ASA 5505 to 9.0(1) as I would like to use ipv6 version of dhcprelay. That said, I am unable to obtain a global unicast address but the link-local address is able to communication with the ISP's gateway/DHCP provider which I hope will allow v6 dhcprelay provide internal clients with IP's from the ISP. Trouble is, unsolicated inbound ICMPv6 messages from the ISP's gateway are being dropped on the way into outside interface.
%ASA-3-313008: Denied IPv6-ICMP type=129, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
[Code]...
View 4 Replies
View Related
Nov 5, 2012
Trying to allow inbound access from any host outside to my LAN server on port 995. [code]
View 1 Replies
View Related
Feb 28, 2012
I have a weather station at our high school that needs UDP port 9500 open inbound/outbound to specified IP addresses.
Cisco PIX Security Appliance Software Version 8.0(4)
Device Manager Version 6.1(5)57
View 1 Replies
View Related
Sep 2, 2012
I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox.
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).
View 3 Replies
View Related
Oct 30, 2012
Trying to do port forwarding so that one particular host located on the WAN can get access to a LAN box on a specific port via the public IP.
Here's what I've setup on the ASA (IP addresses and port number have been changed to protect the innocent):
View 1 Replies
View Related
Jan 23, 2012
I would like to be able to do SSH port forwarding from outside to an IP address inside. Normally, this is very straighforward.
The problem now is that if I do so, then the LAN to LAN VPN stops working!.There is a LAN to LAN VPN working flawlesly (so far) between an ASA 5505 and a Cisco 861 Integrated Router. However, I would like also, to give SSH access to an IP address behind the Cisco router. The moment I do this the VPN breaks!
I attached the Cisco 861 router configuration, where the problem shows. The ASA has public IP X.X.X.105 and the router has X.X.X.105. These two are used for the VPN tunnel.
The internal network in the ASA is 10.115.16.0/24 and 192.168.10.0/24 in the router. These talk to each other using the tunnelt. But, the moment I try to forward port 22 in the router from X.X.X.107 to 192.168.10.30 the VPN breaks! I do that with the following line: ip nat inside source static tcp 192.168.10.30 22 X.X.X.107 22.Obviously, something is eluding me. The configuration is rather short and simple. But, I'm a newbie with Cisco rotuer configuration. Note that the tunnel stays up after I use the natting entry and I can talk from the router to the ASA, but not the other way around!The router is Cisco 861 with IOS version 15.0(1)M7.
View 1 Replies
View Related
Dec 1, 2012
Setup firewall rules that will block all inbound Internet access to the web server except port 443, Setup firewall rules that will block all communication between the two internal networks, except ports 7000 and 1702
View 1 Replies
View Related
Mar 16, 2011
We have an ASA 5505 and I need to set up port forwarding for an unusual port number which will be used for FTP on an IIS server.It's a bit complex as there are 3 VLANs: these are called ISP, Server and LAN-side VPN. We need to add a TCP port 8521 forward from the server's IP in Server WAN to ISP WAN VLAN with public IP address.
View 1 Replies
View Related
Jun 27, 2011
We are trying to install filter software at our main location and branches. The admin console has been installed at the main branch, but I need to allow access to ports 58000-58003 through our firewall in order to successfully install the software at our branches.
View 1 Replies
View Related
Apr 23, 2012
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
!
[code]......
View 2 Replies
View Related
Apr 19, 2013
I have a Cisco home rack lab which is behind my ASA 5505. I use my ASA to connect to the internet. My situation is I travel a lot for work, and I am unable to do my labbing practice. I am pretty new to ASA and would like to do a port forwarding to access my access server which is connected to my Cisco routers and switches.My network topology is this: (internet)-------(ASA 5505)----------(3550)-------(CM32 Access Server)----------(Cisco Rack) This is how I setup my remote access:
Code:
ssh 0.0.0.0 0.0.0.0 outside
View 8 Replies
View Related
Jan 26, 2013
just getting started with ASA's. I've got my 5505 almost 100% configured but my port 25 forward to my Exchange server. Currently I've got an access list forwarding all traffic that hits the outside interface on port 25 to my Exchange server (access-list outside-in extended permit tcp any object mail-port-25 eq smtp). What I'd like to do now is say that only port 25 traffic from specific IP subnets gets forwarded. I thought I read that there's a couple of way to do this (from the inside interface, from the outside interface).
Also, what happens to port 25 hits that don't fall within the range I specify? Do they get a disconnect reply or do they just get ignored (no reply whatsoever)?
Edit: ...just to clarify, the allowed IP's I will be entering are the WAN IP's of my AS/AV service.
View 6 Replies
View Related
Apr 7, 2013
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies
View Related
Oct 27, 2011
I think the ASA5505 I have is in basic license. When I open the third interacse : dmz it must activate No Forward command then can work.
Any way to resolve this problem? is it must pay money to buy the license so that can work without No Forward command?
If have to pay to make it work without No Forward command, how to pay and make it work and how much is the cost in USD?
View 2 Replies
View Related
Aug 9, 2012
I have a cisco 5520 with 8.4.4(1) and I already have a NAT for an email server on it.Here is the IP and ports on current configuration:
Email Server Private IP: 1.1.1.1
Email Server Public IP: 2.2.2.2
Email Server Local Ports : 25, 587
Right now I have ports 25 and 587 opened for 2.2.2.2 so, now I need to add a port redirection for another port:
New Port : 8925
I need to redirect 2.2.2.2:8925 to 1.1.1.1:587
View 1 Replies
View Related
Apr 11, 2013
i'm having a problem portforwarding/redirection for the pix 501?I'm trying to open the ports 49003 and 40085 in order to view our dvr remotely and i'm not exactly sure how to it.
View 11 Replies
View Related
Nov 5, 2012
I have an issue with portforwarding in my teleeye cctv behind asa 8.4. I can browse the DVR outside via http however when i attempt to login, "server busy" will prompt afterwards. Note: Theres no issue when acesssing the DVR locally.
Heres my config.
OUTSIDE INTERFACE:
interface Ethernet0/3
speed 100
duplex full
[Code]...
View 4 Replies
View Related
May 2, 2011
i have a asa with a outside IP address of 140.32.121.5. behind this firewall i have a cisco MWR 2941 that i would like to connect to via telnet. its inside ip address is 10.10.10.2. my reasoning for this is because i cannot SSH or telnet from a ASA so i need to have the ASA push my telnet request to the router on its inside interface.i have tried some NAT examples but i am very green with NAT. i have also built access lists that look like the follow " access-list 101 permit tcp any 10.10.50.2 eq 23. and then tied the access-group 101 with the outside interface. this also with no success.
View 1 Replies
View Related
