I'm currently using Cisco EPC 3000 cable modem and Airlive wt-2400r router. Afaik the cisco isn't a router, but i'm still having some weird problems with forwarding and apparently even DMZ wont work .
View 10 RepliesI'd need to protect access to a very critical web site on my LAN.To achieve this I have been thinking to use a cisco ASA, because Cisco VPN3000 appliances are out of market now. But i do not know if I can achieve what I'd wish to do.I need (upon authentication) that an user connection to port 443 is forwarded to port 443 (or another TCP port)to my internal LAN where is the critical web site.So basically I need a feature like the WebVPN functionality of the Cisco VPN 3000 serires where you can logon.using web interface and you are forwarded to specific TCP port or you jsut type the web site where you want to go after authentication. For maximum compatibility (because users can be anywhere in the world and IPSEC or PPTP can be filtered) I'd need to do this with an SSL port forwarding.Is it possible to do this with the SSL VPN configuration options of the Cisco ASA ? Is it possible then to authorize users using LDAP group matching and authenticate users using kerberos 5 ?
View 3 Replies View RelatedI have tried everything possible with this modem and router. I cant figure it out. I tried the router in bridge mode, tried opening the ports up on both of them.
View 14 Replies View RelatedI have at&t DSL with Westell Modem/Router in Bridge Mode and Linksys Router connected. The internet is working fine, but I'm unable to forward ports on the Linksys Router. The ports are 80 and 37777.
View 1 Replies View RelatedI'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
I have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View Relatedport forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.
View 1 Replies View RelatedI've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View RelatedI have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.
View 2 Replies View RelatedI need to setup some port forwarding on my X3000 to pass through the firewall to my server but cannot find the relevant page in the setup GUI.
View 2 Replies View RelatedI'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.
I recently swapped routers from a dlink to a Cisco WAG120N, from what I can see the wireless is flaky on this device and has led me to switching the wireless off for my sanity and to stop the complaints of my family when they attached to an access point that suddenly disappeared and then reappeared and disappeared, you get the picture.
What I cannot understand is why when it comes to port forwarding did the developers add the local LAN prefix so for example as default the local LAN interface is 192.168.1.1 and the port forwarding screen is completed to forward a port to a host with address 192.168.1.X by stipulating the prefix I am unable to use the router to port forward to hosts that live beyond by local LAN.This added to the wireless being disabled is becoming a very expensive branded door stop.
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies View RelatedI vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies View Relatedis it possible to connect the wan port of a cable modem to a lan port of the home network? the reason is, i need some wifi access and more ports to my wired network, and the most reasonable solution would be a cable modem router with wifi and 4 ports just plugged into one of my routers.
View 2 Replies View RelatedI have got a Linksys @ Home HG200 V2 G Gateway. I am trying to setup port fowarding but its not working. I have gone onto the routers port forwarding setup page filled it out but the port is still closed.
View 4 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedUsing a Mac running Mac OS X 10.6.8 with VPN Tracker 6.3.0.Before switching to the WAG320N I had no issues with my IPSEC VPN client. After the switch it consistently fails in Phase 1 negotiation.In the log file of the gateway I only notice: Mon, 2011-08-22 07:47:31 - [Outgoing] UDP Packet - 192.168.1.100:500 --> IP.ADDRESS.VPN.GATEWAY:500.The software itself complains about timeouts while contacting the remote gateway.VPN pass through is enabled, no port forwarding is set up, firewall is disabled.
View 6 Replies View RelatedOur small business just moved into a new building and I am in charge of setting up the network infrastructure. I am not new to computers or networking but I have never had to deal with this set up before.
Our current set up.We have a cable modem from comcast that has the Coax cable connected to it.The modem has 4 ports on it. The ports are connected to a built in 24 port switch that was already in the building. The switch has it's ports connected to outlets in the walls. Currently we have 4 computers on our network and since the cable modem had 4 ports it worked fine.
What we need? We will have another person join our office so I will need to activate one additional port on the switch that already exists. However, since all 4 ports on the modem are already taken, I have no way to add an additional port. They also want us to get wifi in the building.How I think I have to solve the problem (most likely wrong).I have to get another switch (like 8 port) and connect the cable modem to the switch using a cross over cable (if there is no designated internet port). Since I have the modem connected to the switch, I will have to move the 3 remaining connections to the switch.
Then I connect the 4 remaining ports on the switch to the existing 24-port switch that is already there. I will use one of the outlets in the building to connect an AP for Wi-Fi for better signal. Currently the modem and switches are hidden in a closet away from the office space and would mess up the signal.
I was working with Motorola SB6120 cable modem regarding an odd power cycle issue (it would power cycle randomly for 24 hours). While trying to diag the issue, I was taking a peak in his router config and found a port set to forward as:
Application: Comcast
Port From: 888
Protocol: Both
IP: 192.168.100.1
Port To: 80
I understand that his modem admin page is now available from the internet. He said his friend set this up to "modem", but I don't see any advantage of having this done. At this point what are the other advantages of forwarding such ports?Another key note: When the port forwarding was disabled, suddenly the power cycle issues stopped.
I am looking to permanently reset the default remote management port of the MODEM DPC3825 to something other than 8080. how to PERMANENTLY change the port from 8080? In the web interface under administration I have several times set it to something else other than the defaulted 8080 but when the modem is rebooted or reset, it goes back to the default 8080.
View 4 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View RelatedI'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
View 3 Replies View RelatedI have a customer who needs to be able to do port forwarding so his branch sites can log into virtual machines. They currently have a Cisco 877 router which was installed by someone else. I have no idea how to work it or if this is even possible on this router.
View 2 Replies View RelatedWe have the following port forwards set up on a Cisco 800s router. All internal IP addresses are NATd out to the IP on fa4 which is the external interface. Traffic recieved on fa4 is forwarded to different servers depending on the type of traffic recieved.
We can browse the internal websites from the internet fine, but there is one internal server 192.168.1.7 that uses a db server (192.168.1.5).. it accesses it on its external IP (fa4) on port 1433 but for some reason the connection does not work.. could this be because the source and destination IP addresses are the same IP address?
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.1.7 21 interface FastEthernet4 21
ip nat inside source static tcp 192.168.1.7 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.1.7 443 interface FastEthernet4 443
ip nat inside source static tcp 192.168.1.5 1433 interface FastEthernet4 1433
ip nat inside source static tcp 192.168.1.7 990 interface FastEthernet4 990
Trying to connect to a computer on a client's network. He has a Netgear WGR614v9 router. I talked him through opening port 23 to 192.168.1.200. I have done this many times on other routers and it should have been simple but could not connect. Had him enable ping response so I could ping his router to verify the connection and ping was good. Tried my port scanner and only port 21 is open. Had client verify the port forwarding data and it is correct. Does he need to restart the router to enable port forwarding?
View 4 Replies View RelatedI'm finally jumping in over Christmas break to set up a Y network with three routers. I run a side business repairing and cleaning viruses/malware from PCs and would like the business subnet not to be able to mix with (and possibly infect) the "home" subnet.Before I knew what I was doing, I set up a simple two router "chained" network by hanging an old SMC router off my main Airport Extreme router, but I've since learned that's not ideal, since the "work" network machines can see everything on the "home" network. So, here's what I want to do. I want to put the new third router right after my cable modem (ISP). I want to keep my Airport Extreme and all devices attaching to it (home subnet) off one LAN port of this new router and my old SMC router off another LAN port of the new router (the test subnet). Currently, the IPs are: [code]My concern in setting up a "Y" configuration is that I have some wireless IP webcams on the Airport Extreme that are using port forwarding (both UDP and HTTP) so I can view them from wherever I am on the Internet, not just from within my home network.
What's the best way to make sure the port forwarding from devices on the Airport Extreme subnet works through the "new" router and out through to the Internet? Do I have to open the same ports on the new router? If so, does anyone have an example using the addresses above? Should I just put the Airport Extreme in the DMZ of the new router (so everything is just passed through - or will that allow my test subnet to see the home subnet? Some other way?
Recently Brighthouse figured out that I was using the wireless router they gave me for actual wireless, and decided to shut it off and tell me I need to pay $100 to use wi-fi on the router. So instead, I went out and bought myself my own belkin wireless router, and plugged it into my old one. Now, I don't know if my old router was indeed a router or a modem. The cable from the wall goes into the older router (let's call that NETGEAR) and from there, an ethernet cable goes into the belkin one (we'll call that BELKIN). Before, when I was using the Wi-Fi on the NETGEAR, port forwarding worked fine, except for having to re-forward ports after my dynamic ip changed. Now, because of the BELKIN router, I can't forward anything? I went into the router management at 192.168.2.1 (for the Belkin), went to Virtual servers forwarded the port 25565 No one can connect to my Minecraft server, only when I plug my computer into my NETGEAR with ethernet (hardwire).
View 15 Replies View RelatedI am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.
View 1 Replies View RelatedI use Bit Torrent to trade Grateful Dead concert recordings (all legit trading). I have Verizon DSL, a Westell 6100G Modem and a Linksys WRT 160N V2 Router. The Modem is located at 192.168.1.1 and the Router at 192.168.2.1. In the router setup page I have properly forwarded and triggered my ports. However, when I visit my torrent site, it tells me that I am firewalled or "NAT". I used to have the Linksys WRT54G Router and it was configured to PPPoE and everything worked fine. One day I did a firmware upgrade on the router and it would no longer connect to the internet. I switched ti to Automatic Configuration - DHCP and it connected, but performance was slow and this NAT issue began. I eventually got the new router and I have the same problem. If I set it to PPPoE, put in he username and password, I lose my internet connection. If set to Automatic Config - DHCP it works, but, again, "NAT".
Verizon told me that this newer modem self configures itself as PPPoE and there is no need to set the router to PPPoE but I can't seem to get these ports forwarded or get around this NAT issue. It is causing a significant loss of performance and while torrenting I can not connect to others, meaning I can not share what I have downloaded (the torrent client won;t upload). I have been screwing with this for months and have spent endless hours on the phone with Verizon - Linksys says my router is out of warranty so they want $39.95/month for tech support.I have been working with the tech support team on my torrent website and they can't get it figured out either.
I want to port forward, so i can broadcast using icecast but it requires me to access my router. I follow the steps from Setting a Static IP Address in Windows 7 - PortForward.com but from step 4 where i have to access my router in my browser,i write my ip which is: 10.0.0.4 according to cmd, and i just get a "Oops! Google Chrome could not connect to 10.0.0.4" message.I have attached a picture showing info from my cmd. It's in danish but i don't think that should be a problem.
View 3 Replies View Related