I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
Several times a day our router will lose its connection to the internet (the internet light goes off, while the wireless signal stays on). All the computers in the house lose connection to the network while this happens. It will usually happen two or more times right after each other, so the computers can re-connect for a few seconds and then the connection will drop again. Eventually, after this repeats a few times, everything returns to normal.We've tried swapping cables, microfilters and 3 different routers (though all the same model). We tried the test socket, but the same problem happens. An engineer came to test the line but said he couldn't detect any problems. We have good download/upload speeds while the router stays connected and no noise on the phone line. I'm fed up of going in circles with the ISP tech support so I came here instead...One other thing I tried was OpenDNS, but that made no difference either...
Info: The router is a ZyXEL P-660HW-T1 v3... I've tried updating the firmware on it, but it wouldn't let me... If I remember correctly the Router Configuration Interface told me I don't have permission to do that.There are four computers connected.. mine is Windows 7, I'm pretty sure 2 others are as well, and also a Macbook... There's also various stuff like an Ipad, Kindle etc., which all lose connection at the same time.
I don't know if I'm saying this right but, I have two computers in my LAN hooked up by a Ethernet cables to my modem/router zyxel pk5000z we were using theses computers to play together using Game Ranger. We were having some problems connecting to game rooms with a symmetric NAT. When the port forwarding did work it would only let me open ports for one ip adress for 1 computer it seemed. How do you open ports for all computers on your LAN?
View 1 Replies View RelatedI have tried everything possible with this modem and router. I cant figure it out. I tried the router in bridge mode, tried opening the ports up on both of them.
View 14 Replies View RelatedI'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.
I want to port forward, so i can broadcast using icecast but it requires me to access my router. I follow the steps from Setting a Static IP Address in Windows 7 - PortForward.com but from step 4 where i have to access my router in my browser,i write my ip which is: 10.0.0.4 according to cmd, and i just get a "Oops! Google Chrome could not connect to 10.0.0.4" message.I have attached a picture showing info from my cmd. It's in danish but i don't think that should be a problem.
View 3 Replies View Relatedinterface GigabitEthernet0/0
ip address x.x.x.36 255.255.255.248
ip nat outside
ip virtual-reassembly in
no ip route-cache
duplex auto
speed auto
no cdp enable
[Code]
ip nat inside source static tcp 192.168.1.252 22 x.x.x.36 6922 extendable
ip route 0.0.0.0 0.0.0.0 x.x.x.33
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit any
Anything wrong with my config? port forwarding to my ssh wont work. Im using CISCO 1900 Series.
I have at&t DSL with Westell Modem/Router in Bridge Mode and Linksys Router connected. The internet is working fine, but I'm unable to forward ports on the Linksys Router. The ports are 80 and 37777.
View 1 Replies View RelatedI'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
I have an ADSL connection which I would like to have my Cisco Soho 97 ADSL router configured to dialup and forward to port 8080.
My network is 192.168.1.0/24
Router is 192.168.1.1
Server is 192.168.1.4 - Default gateway is 192.168.1.1
I am able to connect using the script below and get a public ip address but i cant get it to connect to the internet?what command to use for port forwarding to 8080?
hostname Router
!
!
ip subnet-zero
ip name-server 212.23.8.1
ip name-server 212.23.3.1
ip dhcp excluded-address 192.168.1.1
[code]...
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
!
[code]......
I have recently replaced an RV082 router that had failed with a new RV082. The previous router was set up to forward port 443 ssl requests to a server in the network. Worked flawlessly for years and that is why I replaced it with same model. The new router is also set up to forward port 443 ssl requests to the new server. The issue is that the router responds with its own certificate and does not forward the request to the server.
View 5 Replies View RelatedI have an RV082 V2 with 2.0.2.01-tm and I am having trouble with getting my Sprint Airvana to connect properly to the mobile service. I've read on the Sprint forums indicate putting the Airvana in the DMZ generally allows the device to work properly; however, none have the RV series routers for tips on how to do this appropriately. This device used to work fine behind the RV082, but I reset it one day and it no longer works.
The Airvana is a femtocell/router device with a WAN port and 3 LAN ports. If I connect the Airvana directly to my cable modem, I get the appropriate connection and can then make calls through the device instead of through the Sprint connection; I live in a basement unit and get crappy signal without the device. This proves the device works and that my ISP is not blocking the ports. Sprint indicates the device uses UDP 53, 67, 68, 500 and 4500. Their support sucks and they insist I put the Airvana before my router. I absolutely do not want to use the Airvana as the router. There are almost no configuration options in the router interface and it needs to be rebooted somewhat regularly, which would drop internet access throughout the house for 10-15 minutes while it reboots and finally establishes an internet connection.
As soon as put the Airvana behind the RV082, I no longer get the appropriate connection. I can, however, plug my computer into one of the LAN ports on the Airvana and connect to the internet in general. I have the router assign a static IP to the Airvana, and tried forwarding the required UDP ports to the IP. This did not fix the problem.
I can certainly troubleshoot the port forwarding issues, but I would also like to look into putting the device into the DMZ, if possible. I've not worked much in this area, so I am unsure how to appropriately configure the router to allow this to happen. Is it possible to have the Airvana in the router DMZ without having a public IP for the device itself?
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies View RelatedI have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View RelatedI'm currently using Cisco EPC 3000 cable modem and Airlive wt-2400r router. Afaik the cisco isn't a router, but i'm still having some weird problems with forwarding and apparently even DMZ wont work .
View 10 Replies View Relatedport forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.
View 1 Replies View RelatedI've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View RelatedI have a Zyxel storage box. How do I find it's IP address if I have it's MAC address? I am trying to connect to it but don't know the IP.
View 4 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI have an issue/doubt regarding the configuration of a modem + router. The modem is a netopia-3000 (who care ) and the router is a netgear WGR614V9, The first has the address 192.168.1.1, the second 192.168.0.1 My pc in dhcp take the address from the router (192.168.0.x) and internet work, but if I set the ip manually 192.168.1.x it stop to work, why?
View 1 Replies View RelatedHave a ZyXEL 600 wireless router - it has worked without issues for years.However yesterday evening my wireless router suddenly stopped broadcasting a signal. 2 different PC's and a wifi dongle attached to our TV were suddenly all unable to find my network.The WLAN light on the router was still lit up. I connected my Acer Aspire 5742Z laptop to the router via an ethernet cable and it worked fine. I connected to the router and it said there were no errors.
View 14 Replies View RelatedI bought a new modem (Zyxel P-660H-D1) few weeks ago and since then my internet has been alot slower than before. When i start up my computer, it isn't actually that slow at first... it starts getting slow after around 10-20 minutes. I also started getting bluescreens from time to time. My downloads aren't that much slower then before, but loading internet pages is painfully slow and online games are lagging alot. This is also happening with my xbox360, so I don't think it's my computers fault. With my old modem (Telewell EA-501) I was getting around 6Mbps, but with the new one its only around 1-2Mbps. My ping is also very high (around 400ms) and I have some packet loss. My jitter is 200ms.
View 1 Replies View RelatedMy ZyXEL modem/router does not detect my ethernet cables. it has one that runs to the main computer and i have a cable connected to my xbox. the light does not turn on when i try to use the internet for my xbox and the xbox does not detect ethernet. the other port works fine for the computer.
View 1 Replies View RelatedEssentially, I have a spare desktop computer I'd like to turn into a web server, but my modem and wireless router are very difficult to work with. I installed Apache HTTP and successfully hosted a test page which can be accessed anywhere on the LAN. However, I'm having trouble setting up the server to be accessed from my external IP address.
I was supplied with a ZyXEL EQ-660R DSL modem by my ISP (CenturyLink) and bought a Netgear WGT624v3 wireless router in which to connect my laptop and spare desktop.
ZyXEL's website is not useful, and I don't think much of the problem is with the Netgear router. I've played with many settings and have tried to forward port 80 from the modem, but I've had no luck.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
To play one i game i need to open ports 7777 and 7778 , to do that i must access my router.When i connect to standard router ip192.168.1.1 it wont work. To solve my problem i checked the name of router and read the official support.My routers model is Speedtouch 546 v6. and at official faq the adress is given, but it still wont work, then i noticed i have second router i think, its used to connect 2 TV for my internet television, its model is Zyxel ES- 105 a , in official support , their given adress wont work.
View 14 Replies View Relatedhow to open UDP port 16000 in my router Zyxel MAX 206 M1R...when i tried to start AGE OF EMPIRE 2 THE AGE OF THE KING in gameranger it says that my UDP port 16000 is not opened...so i am trying to open it..
View 2 Replies View RelatedI have a 4-port Zyxel P334U with WLAN, and I would want to set it up so that besides normal WAN, each connected computer also has access to the other local computers. I've tried setting it up before, but haven't managed to get it working, so I gave up.I have DHCP set up, beginning at 192.168.1.16. WAN and ISP DHCP works, so each computer has a local IP (192.168.1.x) and a remote IP given by the ISP.
View 6 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
