Zyxel P660H D1 Modem - Internet Very Slow
Aug 26, 2012
I bought a new modem (Zyxel P-660H-D1) few weeks ago and since then my internet has been alot slower than before. When i start up my computer, it isn't actually that slow at first... it starts getting slow after around 10-20 minutes. I also started getting bluescreens from time to time. My downloads aren't that much slower then before, but loading internet pages is painfully slow and online games are lagging alot. This is also happening with my xbox360, so I don't think it's my computers fault. With my old modem (Telewell EA-501) I was getting around 6Mbps, but with the new one its only around 1-2Mbps. My ping is also very high (around 400ms) and I have some packet loss. My jitter is 200ms.
View 1 Replies
ADVERTISEMENT
Jun 7, 2012
Setup a dir 655 and connect it to a P660H-D1? The P660 is a ADSL2+ modem with a 4 port switch on the back side. I want to be able to connect the dir 655 so I can utilize the wireless piece.I have the P660 connected now and I can get on the net fine when in routing mode. If I connect my dir 655 to a ethernet port on the back of the P660 I never get a wireless signal that allows me to connect.
View 8 Replies
View Related
Jul 28, 2012
My ZyXEL modem/router does not detect my ethernet cables. it has one that runs to the main computer and i have a cable connected to my xbox. the light does not turn on when i try to use the internet for my xbox and the xbox does not detect ethernet. the other port works fine for the computer.
View 1 Replies
View Related
Oct 9, 2011
I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies
View Related
Dec 21, 2010
Essentially, I have a spare desktop computer I'd like to turn into a web server, but my modem and wireless router are very difficult to work with. I installed Apache HTTP and successfully hosted a test page which can be accessed anywhere on the LAN. However, I'm having trouble setting up the server to be accessed from my external IP address.
I was supplied with a ZyXEL EQ-660R DSL modem by my ISP (CenturyLink) and bought a Netgear WGT624v3 wireless router in which to connect my laptop and spare desktop.
ZyXEL's website is not useful, and I don't think much of the problem is with the Netgear router. I've played with many settings and have tried to forward port 80 from the modem, but I've had no luck.
View 1 Replies
View Related
Jul 19, 2012
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
View 2 Replies
View Related
Dec 30, 2012
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
View 8 Replies
View Related
Jul 18, 2012
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
View 1 Replies
View Related
Mar 21, 2011
My laptops internet runs super slow, but only at our house.It runs at top speed on any other network. My wifes laptop has no issues at all. Have done multiple virus check with multiple different anti virisus programs.We use a Netgear modem I usually connect wireless, but have connected with an Ethernet cord with no change in speed.
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM)2 Duo CPU P7450 @ 2.13GHz, Intel64 Family 6 Model 23 Stepping 6
Processor Count: 2
RAM: 4063 Mb
Graphics Card: ATI Mobility Radeon HD 4650, 1024 Mb
Hard Drives: C: Total - 463711 MB, Free - 389512 MB; D: Total - 13026 MB, Free - 2178 MB;
Motherboard: Quanta, 3628, 18.42, CNF9401DLR
Antivirus: AVG Internet Security, Updated and Enabled
View 3 Replies
View Related
Mar 31, 2011
I had to made some hardware changes. All the computers are running windows XP. I changed out to a Motorola 2210 modem, d-link dir-825 router and DGS-1008G switch.Everything was fine until I made this change. I now have internet, but it is slow.
View 3 Replies
View Related
Mar 22, 2011
So I've had this problem before and normally I solve it by simply unplugging everything from my modem and router but ive tried that this time several times to no avail. The internet suddenly cut out one day and when I did my usual unplugging thing it came back unbearably slow.Right now I'm running off a motorola SB5100 Surboard modem and a linksys WRT54G2 router and its not my computer, everyone in the house is getting terrible speed.
View 10 Replies
View Related
Nov 10, 2011
everytime I turn on my PC it doesn't see the modem or router and won't connect to internet. I have to turn on the PC, unplug the modem and router and replug them in before it sees the internet.Any other way of doing it doesn't work. (I leave modem router on 24/7, PC is the one in sig, running Win &. Modem is an older Motorala surfboard, wireless is ZyXEL XtremeMIMO X-550 Router.
View 2 Replies
View Related
Apr 23, 2012
I am trying to access the internet trough my WRT610N connected to a ZyXEL P-2601HN provided by my ISP.
I have the WRT610 all setup and working, but I cannot connect to the internet. The WRT610N is a the latest firmware version.
The WRT610 is connected (Internet) by cable to the Zyxel (one of the four ports)with a cat.5E patch cable.
the wireless is so much better on the WRT610N than the ZyXel.
View 3 Replies
View Related
Jun 20, 2012
I do not have access to internet (I'm on some unsecured internet from around here now, very slow). When I start the internetdiagnostics from windows, he says it's the modem or the connection from laptop, router, modem to internet. However, the lights indicating internet and dsl on the modem are brightly burning and the router shows nothing abnormal too.
I have a WPA2-PSK security, the modem is Zyxel. Also, the ethernetcable portal on my laptop is broken, so I can't do anything non-wireless. My phone has the same problem with this internet, it can get a connection, but no internet.
View 3 Replies
View Related
Sep 15, 2012
Just recently got a Zyxel VSG1432 router connected to the main computer in my home. I am now trying to connect my laptop wirelessly. It will connect to the router but says it is an unidentified network and it doesn't connect to the internet. There is an x in the network and sharing window.I have tried restarting the router, going to the router webpage and resetting to factory settings, none of this worked. Also contacted the service provider and spoke with two tech guys, but still no luck.
View 1 Replies
View Related
Nov 24, 2012
I'm having a problem with my internet. My old modem broke so I took it back to get a new one from Comcast. The new modem works but it's having problems. The download speed is very spiky and random. If I reset my modem, it goes back up to it's average speed (25mb/s) and stays that way as a constant for a little bit. Then it randomly starts spiking between 1-10mb/s and my internet (especially while gaming) gets extremely laggy. I can restart the modem again and the speed goes back to normal, but it always slows back down again. I've tried connecting the modem to the computer directly and the speeds are the same, so it rules out a problem with my router. [code]
View 8 Replies
View Related
Mar 15, 2013
my PC and laptop are both suddenly running sluggish since yesterday morning. pages take forever to load; slow to start videos, etc. i called ATT this morning...the auto test said i needed to talk to someone because there was a problem noted. but the live rep ran tests and said the speeds were within the norm for my service. i asked her why the auto test reported an issue, and she checked, only to come back to say "it's a problem with the modem." oh, and a new one from them is $80-100+
[code]...
View 2 Replies
View Related
Apr 29, 2013
I have a Linksys E1200 modem and I am only getting less than 1.0 mbps download speeds. When connected via ethernet cable to the router, my download speed is > 50 mbps.
View 2 Replies
View Related
Nov 30, 2012
I am using a Thomson ST516 v6 DSL Modem, through which I have connected a Tenda W311R+ Wireless Router. There's two laptops, one running Windows 7 Sp1, the other running Windows Xp Sp3, and an Android based phone using this connection. I should mention that the problematic laptop had Windows 7 before switching to Xp and ran without any issues.
[code]....
View 12 Replies
View Related
Mar 23, 2011
Is there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies
View Related
Jun 21, 2012
I have an Att combination Netgear modem-router that is painfully slow when accessing wi-fi gear remotely. Everything works great on the lan, but often times out on remote access over the internet.
View 3 Replies
View Related
Dec 11, 2011
So I have a really neat computer sitting here, 2500K, P8z68-v, samsung 830 64gb ssd, corsair vengeance 16gb, deskstar hdd, firepro v5800
I have a non-descript trendnet 56K v.92 dial up modem installed to pci slot1 on my mobo.The phone company says they can't get a quicker connection than 31.2 Kbps established to dial up users in this area.The real issue is the data transfer rate.I have seen it reach as high as 6.xx Kbps but generally hovers around 2.5 Kbps.Now it is down to 1.xx Kbps and I took the last 48 hours downloading all the updates for windows and several other updates for hard ware etc.Now I need the ATI firepro update and 114 Mb will take over 16 hours at my average speed, and some 32 hours at the new slower speed
View 17 Replies
View Related
Mar 25, 2011
I have a Netgear 600 dual band router connected to a DOCIS 3.0 cable modem with a 25mps internet connection from my ISP, should be fast right? When I run a speed test on my comp I get 10-13 mbps download on average. Here's the issue, upon visiting my mothers house and running the same speed test I got very similar results. She is running a Lynksys G router on a DOCIS 2.0 cable modem with 12mps connection. My question is, how can this be so, am I at the limits of my comps g network card? as a disclaimer I would like to note I am connected to the G band on both routers.
View 1 Replies
View Related
Aug 6, 2011
I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
View 4 Replies
View Related
Dec 20, 2012
I have a Zyxel storage box. How do I find it's IP address if I have it's MAC address? I am trying to connect to it but don't know the IP.
View 4 Replies
View Related
May 21, 2012
I have a P-660HW-T1 v3 its using V3.70(BYD.1) | 02/11/2010.when I try to update it to 3.70(BJZ.10)C0 the update fails to succeed.
View 1 Replies
View Related
Feb 9, 2012
I've seen a couple of expired threads on this subject, so I'm sorry for resurrecting it! I have just got a ZyXEL P660HN-TxA router/modem on my home landline to use for wifi with my smartphone. The problem I have is it won't stay connected for long. It connects quickly & browsing is fast for a few minutes, but then it just kicks me offI am still connected to the wifi, but I can't browse anything or re-connect to the internet. Sometimes I can use it for up to 10/15 minutes before it kicks me off. I have to reset the modem, or turn the wifi off then back on via my phone.
View 4 Replies
View Related
Feb 17, 2011
I have a an old router that I changed out when I switched over to fibernet that was just gathering dust, so I decided to include it in my network to extend the wireless range, so the signal is stronger throughout the whole house.Now, the only reason I attach it is to extend the wireless distance, nothing more.Both routers are exactly the same (Zyxel P2602HWT), and the second router is connected through an ethernetcable going to the DSL port. I can connect to the SSID just fine, but it's not actually connected to the internet, only locally (as I can configure the router).I have turned OFF DHCP for the second router, that I only intend to use as a second access point.
View 1 Replies
View Related
Apr 1, 2013
How do I clear my router DNS cache on my ZyXEL P-660 router?I already cleared it on my PC with "ipconfig /flushDNS" in the command line but everyone sees my online IP camera, except me my online IP camera on LIVEwhen I try to access the camera URL i go to the router default/settings/home page
View 10 Replies
View Related
May 16, 2011
I have earthlink as ISP. I tried everything they said to do to use my modem/router with the linksys router (as wired not wireless), but to no avail. I switch to bridge mode on the Zyxel and then the Internet connection drops. I can't seem to connect to the internet once I plug it to the Linksys.
View 5 Replies
View Related
Jul 15, 2012
Although the configuration is done, when a document is sent to the printer it gives error and does not print. We're using zyxel p2812.
View 1 Replies
View Related
Mar 12, 2013
I've been using ZYXEL PLA-401 v1 Homeplug adapters for years to connect various devices to my router for a "more stable" than wireless connection. This worked fine in my last house, connecting a switch in our office to the router. We've now moved and I have got some more homeplug adapters to make a few other more reliable connections.
Problem is, the new adapters can't see the old adapters on the homeplug network. They can see each other, as can the old ones. I suspect a firmware or network name mismatch - I've tried to change settings on each of them but the Zyxel utility doesn't appear to do much. I can't set the DAK names, nor can I change the network names. The firmware update utility doesn't work on Windows 7 (gives a cannot find Windows path error).
using the Zyxel configuration utility and firmware upgrade tool on Windows 7 / Ubuntu?
View 1 Replies
View Related
Dec 7, 2011
i have recently successfully configured an IPSEC VPN from a SRP541 to our Zyxel Zywall 70 (main site).
I can ping all devices on the remote Site except the Cisco-Router!I tried to disable tohefirewall and did set "Anonymous Internet Requests" to "disabled".But still no ping (and no web management) over the VPN possible.
I must admit i am totally new to Cisco devices (up to now, we used only Zyxel) - so is guess it must be something very basic i am missing.
View 1 Replies
View Related
