I have a an old router that I changed out when I switched over to fibernet that was just gathering dust, so I decided to include it in my network to extend the wireless range, so the signal is stronger throughout the whole house.Now, the only reason I attach it is to extend the wireless distance, nothing more.Both routers are exactly the same (Zyxel P2602HWT), and the second router is connected through an ethernetcable going to the DSL port. I can connect to the SSID just fine, but it's not actually connected to the internet, only locally (as I can configure the router).I have turned OFF DHCP for the second router, that I only intend to use as a second access point.
I am a mac user, and whenever I try to open this following link: [URL] to log in my router, nothing happens. Firefox and/or Safari browse the link for a while, but then nothing happens. I am using a Zyxel prestige series 600.
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
I need to create a VPN tunnel between two offices of the same company. I bought two Zyxel P-661HW-D to create the secure VPN tunnel but the problem is that the two offices has a ADSL connection with dynamic IP. Is possible, with this router, to use a DDNS service to create the VPN tunnel or it' s required to have static IP ?
Have a ZyXEL 600 wireless router - it has worked without issues for years.However yesterday evening my wireless router suddenly stopped broadcasting a signal. 2 different PC's and a wifi dongle attached to our TV were suddenly all unable to find my network.The WLAN light on the router was still lit up. I connected my Acer Aspire 5742Z laptop to the router via an ethernet cable and it worked fine. I connected to the router and it said there were no errors.
I just updated the firmware on my ZyXEL NBG-416N router and now I cannot see the wireless network being broadcasted on my PC. Other devices in my home can view this network including my phone, HDTV and laptop. I have reset the router, modem and computer several times but my PC still cannot find that specific wireless network.I am using Windows 7 64-bitASUS 802.11n Wireless LAN CardAny reason that my computer is unable to find this specific network but can find others? switchie15 has chosen the best answer to his/her question.Click here to view the answer that was selected.
I've seen a couple of expired threads on this subject, so I'm sorry for resurrecting it! I have just got a ZyXEL P660HN-TxA router/modem on my home landline to use for wifi with my smartphone. The problem I have is it won't stay connected for long. It connects quickly & browsing is fast for a few minutes, but then it just kicks me offI am still connected to the wifi, but I can't browse anything or re-connect to the internet. Sometimes I can use it for up to 10/15 minutes before it kicks me off. I have to reset the modem, or turn the wifi off then back on via my phone.
How do I clear my router DNS cache on my ZyXEL P-660 router?I already cleared it on my PC with "ipconfig /flushDNS" in the command line but everyone sees my online IP camera, except me my online IP camera on LIVEwhen I try to access the camera URL i go to the router default/settings/home page
I have earthlink as ISP. I tried everything they said to do to use my modem/router with the linksys router (as wired not wireless), but to no avail. I switch to bridge mode on the Zyxel and then the Internet connection drops. I can't seem to connect to the internet once I plug it to the Linksys.
Setup a dir 655 and connect it to a P660H-D1? The P660 is a ADSL2+ modem with a 4 port switch on the back side. I want to be able to connect the dir 655 so I can utilize the wireless piece.I have the P660 connected now and I can get on the net fine when in routing mode. If I connect my dir 655 to a ethernet port on the back of the P660 I never get a wireless signal that allows me to connect.
I've been using ZYXEL PLA-401 v1 Homeplug adapters for years to connect various devices to my router for a "more stable" than wireless connection. This worked fine in my last house, connecting a switch in our office to the router. We've now moved and I have got some more homeplug adapters to make a few other more reliable connections.
Problem is, the new adapters can't see the old adapters on the homeplug network. They can see each other, as can the old ones. I suspect a firmware or network name mismatch - I've tried to change settings on each of them but the Zyxel utility doesn't appear to do much. I can't set the DAK names, nor can I change the network names. The firmware update utility doesn't work on Windows 7 (gives a cannot find Windows path error).
using the Zyxel configuration utility and firmware upgrade tool on Windows 7 / Ubuntu?
how to port configuration from a cisco 2950 to a zyxel gs1910. the configuration on the cisco is pretty staright forward. I need to configure an uplink port to the router which can handle all VLAN which currently looks like this
To play one i game i need to open ports 7777 and 7778 , to do that i must access my router.When i connect to standard router ip192.168.1.1 it wont work. To solve my problem i checked the name of router and read the official support.My routers model is Speedtouch 546 v6. and at official faq the adress is given, but it still wont work, then i noticed i have second router i think, its used to connect 2 TV for my internet television, its model is Zyxel ES- 105 a , in official support , their given adress wont work.
I bought a new modem (Zyxel P-660H-D1) few weeks ago and since then my internet has been alot slower than before. When i start up my computer, it isn't actually that slow at first... it starts getting slow after around 10-20 minutes. I also started getting bluescreens from time to time. My downloads aren't that much slower then before, but loading internet pages is painfully slow and online games are lagging alot. This is also happening with my xbox360, so I don't think it's my computers fault. With my old modem (Telewell EA-501) I was getting around 6Mbps, but with the new one its only around 1-2Mbps. My ping is also very high (around 400ms) and I have some packet loss. My jitter is 200ms.
how to open UDP port 16000 in my router Zyxel MAX 206 M1R...when i tried to start AGE OF EMPIRE 2 THE AGE OF THE KING in gameranger it says that my UDP port 16000 is not opened...so i am trying to open it..
I purchased a ZyXEL 3205 to serve as a universal repeater in my house, to boost the DSL wireless signal from upstairs to downstairs. I have a 2WIRE router, and my DSL is through AT&T. The wireless works just fine (and we've been connecting multiple devices through it for over a month), but the signal is weak downstairs, so this seemed like a good cheap solution.I found several good sets of instructions on setting up the 3205 as a repeater, so while complex, that was not really a problem.
However, the 3205's status is still marked as "disassociated", which means that it won't connect to the 2WIRE. It can see the signal, and I'm telling it to connect and giving it the correct key. It also broadcasts just fine, since my wireless devices can connect to the 3205 when it is turned on. However, the 3205 refuses to actually connect to the 2WIRE for some reason. Is there a known issue with connecting? I've checked all the obvious things - they're set to be on the same wireless channel, both using the same encryption settings, and there aren't any ip conflicts happening, since the 3205 is set to an unclaimed ip in the same space.
everytime I turn on my PC it doesn't see the modem or router and won't connect to internet. I have to turn on the PC, unplug the modem and router and replug them in before it sees the internet.Any other way of doing it doesn't work. (I leave modem router on 24/7, PC is the one in sig, running Win &. Modem is an older Motorala surfboard, wireless is ZyXEL XtremeMIMO X-550 Router.
The BT Infinity Hub (fibre optics to the cabinet one) plugs into a router and I tried connecting via ethernet cable to both without result, still no set up page from [URL] either with wi-fi off or with wi-fi on in the "Currently connected to:" window.
We have a ZyXEL (P-2601HN-F1) router and three computers in our house. Currently, we only use cables to connect to the router because we haven't been bothered to setup wireless. However, there's a curious problem where the moment we connect more than 2 devices at a time, the router loses connection to the internet. To be precise, all LEDs are on, except wireless (d'uh) and Internet.
So my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
My ZyXEL modem/router does not detect my ethernet cables. it has one that runs to the main computer and i have a cable connected to my xbox. the light does not turn on when i try to use the internet for my xbox and the xbox does not detect ethernet. the other port works fine for the computer.
I don't know if I'm saying this right but, I have two computers in my LAN hooked up by a Ethernet cables to my modem/router zyxel pk5000z we were using theses computers to play together using Game Ranger. We were having some problems connecting to game rooms with a symmetric NAT. When the port forwarding did work it would only let me open ports for one ip adress for 1 computer it seemed. How do you open ports for all computers on your LAN?
I have one P-660HN-T1A ZyXEL wireless router at my home with 2mbps connection. ZyNOS Firmware Version: 3.40(UTU.0) my brother always keeps on downloading stuffs from bitTorrent and eats up all the bandwidth.
1. is there any way to put speed limit on each user of my wireless router??
2. or is there any way to just block torrent download on my router???
3. QOS [quality of service] setting on Zyxel router so that I make my priority higher than my brother?
I have a 4-port Zyxel P334U with WLAN, and I would want to set it up so that besides normal WAN, each connected computer also has access to the other local computers. I've tried setting it up before, but haven't managed to get it working, so I gave up.I have DHCP set up, beginning at 192.168.1.16. WAN and ISP DHCP works, so each computer has a local IP (192.168.1.x) and a remote IP given by the ISP.
Several times a day our router will lose its connection to the internet (the internet light goes off, while the wireless signal stays on). All the computers in the house lose connection to the network while this happens. It will usually happen two or more times right after each other, so the computers can re-connect for a few seconds and then the connection will drop again. Eventually, after this repeats a few times, everything returns to normal.We've tried swapping cables, microfilters and 3 different routers (though all the same model). We tried the test socket, but the same problem happens. An engineer came to test the line but said he couldn't detect any problems. We have good download/upload speeds while the router stays connected and no noise on the phone line. I'm fed up of going in circles with the ISP tech support so I came here instead...One other thing I tried was OpenDNS, but that made no difference either...
Info: The router is a ZyXEL P-660HW-T1 v3... I've tried updating the firmware on it, but it wouldn't let me... If I remember correctly the Router Configuration Interface told me I don't have permission to do that.There are four computers connected.. mine is Windows 7, I'm pretty sure 2 others are as well, and also a Macbook... There's also various stuff like an Ipad, Kindle etc., which all lose connection at the same time.
Bought the Zyxel Wireless Range Extender to get wifi in farthest rooms in my house but set up is not working because BT have disabled WPS button on Home Hub 3 with my Infinity. Therefore they suggest I try manual set up. This requires browser wtih IP address 192.168.1.2 for Zyxel wireless extender WRE2205, This gives no result (page does not load in IE).
I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
I have a customer who has a Zyxel USG50 security firewall on their network. They utilize a cloud hosted voip solution called Vocalocity that provides SIP voip service to their Cisco phones. They have about 8 phones in a small office.the problem they are having is that as it stands now, all VOIP phones in the office are dynamically assigned addresses internally. However, the VOIP phones are having a ton of issues that we believe may be related to the firewall blocking traffic somehow or not playing nicely with the service.
- Some calls are dropped altogether - Some calls do not ring all phones - Some phones keep ringing even after a call is picked up
While Vocalocity has admitted that they have the "ghost ringing" issue going on with other customers, the dropped calls and not all phones ringing could be firewall related. We are trying to pinpoint what may be going on.i did open up all of the ports that the VOIP provider claims are used by their service, 5060-5090. However, some 5060 packets still seem like they are being blocked in the firewall logs.How does everyone else out there setup their VOIP phones internally to have unfettered access to the internet? Do you recommend just using the DMZ functionality (which I can do on this USG device) or bypassing the firewall altogether somehow? We have some spare switches and another home level Netgear router we can use for testing.
Essentially, I have a spare desktop computer I'd like to turn into a web server, but my modem and wireless router are very difficult to work with. I installed Apache HTTP and successfully hosted a test page which can be accessed anywhere on the LAN. However, I'm having trouble setting up the server to be accessed from my external IP address.
I was supplied with a ZyXEL EQ-660R DSL modem by my ISP (CenturyLink) and bought a Netgear WGT624v3 wireless router in which to connect my laptop and spare desktop.
ZyXEL's website is not useful, and I don't think much of the problem is with the Netgear router. I've played with many settings and have tried to forward port 80 from the modem, but I've had no luck.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
I do not have access to internet (I'm on some unsecured internet from around here now, very slow). When I start the internetdiagnostics from windows, he says it's the modem or the connection from laptop, router, modem to internet. However, the lights indicating internet and dsl on the modem are brightly burning and the router shows nothing abnormal too.
I have a WPA2-PSK security, the modem is Zyxel. Also, the ethernetcable portal on my laptop is broken, so I can't do anything non-wireless. My phone has the same problem with this internet, it can get a connection, but no internet.
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 22.214.171.124 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080. But every configuration I have tried does nothing of the sort.
Just recently got a Zyxel VSG1432 router connected to the main computer in my home. I am now trying to connect my laptop wirelessly. It will connect to the router but says it is an unidentified network and it doesn't connect to the internet. There is an x in the network and sharing window.I have tried restarting the router, going to the router webpage and resetting to factory settings, none of this worked. Also contacted the service provider and spoke with two tech guys, but still no luck.