Setup a dir 655 and connect it to a P660H-D1? The P660 is a ADSL2+ modem with a 4 port switch on the back side. I want to be able to connect the dir 655 so I can utilize the wireless piece.I have the P660 connected now and I can get on the net fine when in routing mode. If I connect my dir 655 to a ethernet port on the back of the P660 I never get a wireless signal that allows me to connect.
View 8 RepliesI bought a new modem (Zyxel P-660H-D1) few weeks ago and since then my internet has been alot slower than before. When i start up my computer, it isn't actually that slow at first... it starts getting slow after around 10-20 minutes. I also started getting bluescreens from time to time. My downloads aren't that much slower then before, but loading internet pages is painfully slow and online games are lagging alot. This is also happening with my xbox360, so I don't think it's my computers fault. With my old modem (Telewell EA-501) I was getting around 6Mbps, but with the new one its only around 1-2Mbps. My ping is also very high (around 400ms) and I have some packet loss. My jitter is 200ms.
View 1 Replies View RelatedI purchased a ZyXEL 3205 to serve as a universal repeater in my house, to boost the DSL wireless signal from upstairs to downstairs. I have a 2WIRE router, and my DSL is through AT&T. The wireless works just fine (and we've been connecting multiple devices through it for over a month), but the signal is weak downstairs, so this seemed like a good cheap solution.I found several good sets of instructions on setting up the 3205 as a repeater, so while complex, that was not really a problem.
However, the 3205's status is still marked as "disassociated", which means that it won't connect to the 2WIRE. It can see the signal, and I'm telling it to connect and giving it the correct key. It also broadcasts just fine, since my wireless devices can connect to the 3205 when it is turned on. However, the 3205 refuses to actually connect to the 2WIRE for some reason. Is there a known issue with connecting? I've checked all the obvious things - they're set to be on the same wireless channel, both using the same encryption settings, and there aren't any ip conflicts happening, since the 3205 is set to an unclaimed ip in the same space.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
I have a Zyxel storage box. How do I find it's IP address if I have it's MAC address? I am trying to connect to it but don't know the IP.
View 4 Replies View RelatedI have a P-660HW-T1 v3 its using V3.70(BYD.1) | 02/11/2010.when I try to update it to 3.70(BJZ.10)C0 the update fails to succeed.
View 1 Replies View RelatedI've seen a couple of expired threads on this subject, so I'm sorry for resurrecting it! I have just got a ZyXEL P660HN-TxA router/modem on my home landline to use for wifi with my smartphone. The problem I have is it won't stay connected for long. It connects quickly & browsing is fast for a few minutes, but then it just kicks me offI am still connected to the wifi, but I can't browse anything or re-connect to the internet. Sometimes I can use it for up to 10/15 minutes before it kicks me off. I have to reset the modem, or turn the wifi off then back on via my phone.
View 4 Replies View RelatedI have a an old router that I changed out when I switched over to fibernet that was just gathering dust, so I decided to include it in my network to extend the wireless range, so the signal is stronger throughout the whole house.Now, the only reason I attach it is to extend the wireless distance, nothing more.Both routers are exactly the same (Zyxel P2602HWT), and the second router is connected through an ethernetcable going to the DSL port. I can connect to the SSID just fine, but it's not actually connected to the internet, only locally (as I can configure the router).I have turned OFF DHCP for the second router, that I only intend to use as a second access point.
View 1 Replies View RelatedHow do I clear my router DNS cache on my ZyXEL P-660 router?I already cleared it on my PC with "ipconfig /flushDNS" in the command line but everyone sees my online IP camera, except me my online IP camera on LIVEwhen I try to access the camera URL i go to the router default/settings/home page
View 10 Replies View RelatedI have earthlink as ISP. I tried everything they said to do to use my modem/router with the linksys router (as wired not wireless), but to no avail. I switch to bridge mode on the Zyxel and then the Internet connection drops. I can't seem to connect to the internet once I plug it to the Linksys.
View 5 Replies View RelatedAlthough the configuration is done, when a document is sent to the printer it gives error and does not print. We're using zyxel p2812.
View 1 Replies View RelatedI've been using ZYXEL PLA-401 v1 Homeplug adapters for years to connect various devices to my router for a "more stable" than wireless connection. This worked fine in my last house, connecting a switch in our office to the router. We've now moved and I have got some more homeplug adapters to make a few other more reliable connections.
Problem is, the new adapters can't see the old adapters on the homeplug network. They can see each other, as can the old ones. I suspect a firmware or network name mismatch - I've tried to change settings on each of them but the Zyxel utility doesn't appear to do much. I can't set the DAK names, nor can I change the network names. The firmware update utility doesn't work on Windows 7 (gives a cannot find Windows path error).
using the Zyxel configuration utility and firmware upgrade tool on Windows 7 / Ubuntu?
i have recently successfully configured an IPSEC VPN from a SRP541 to our Zyxel Zywall 70 (main site).
I can ping all devices on the remote Site except the Cisco-Router!I tried to disable tohefirewall and did set "Anonymous Internet Requests" to "disabled".But still no ping (and no web management) over the VPN possible.
I must admit i am totally new to Cisco devices (up to now, we used only Zyxel) - so is guess it must be something very basic i am missing.
how to port configuration from a cisco 2950 to a zyxel gs1910. the configuration on the cisco is pretty staright forward. I need to configure an uplink port to the router which can handle all VLAN which currently looks like this
View 1 Replies View RelatedTo play one i game i need to open ports 7777 and 7778 , to do that i must access my router.When i connect to standard router ip192.168.1.1 it wont work. To solve my problem i checked the name of router and read the official support.My routers model is Speedtouch 546 v6. and at official faq the adress is given, but it still wont work, then i noticed i have second router i think, its used to connect 2 TV for my internet television, its model is Zyxel ES- 105 a , in official support , their given adress wont work.
View 14 Replies View Relatedhow to open UDP port 16000 in my router Zyxel MAX 206 M1R...when i tried to start AGE OF EMPIRE 2 THE AGE OF THE KING in gameranger it says that my UDP port 16000 is not opened...so i am trying to open it..
View 2 Replies View Relatedcant seem to access my router Zyxel AMG 1202 -T10A, 192.168.1.1 is not working from any computer. Nor is a restart of the router.
View 2 Replies View RelatedI like to create a access point and thinking to buy the Engenius ECB300 or the cheaper ZyXel WAP3205.
I cannot find anything about the power output of the ZyXel WAP3205 so I'm not sure what do buy.
everytime I turn on my PC it doesn't see the modem or router and won't connect to internet. I have to turn on the PC, unplug the modem and router and replug them in before it sees the internet.Any other way of doing it doesn't work. (I leave modem router on 24/7, PC is the one in sig, running Win &. Modem is an older Motorala surfboard, wireless is ZyXEL XtremeMIMO X-550 Router.
View 2 Replies View RelatedI need to create a VPN tunnel between two offices of the same company. I bought two Zyxel P-661HW-D to create the secure VPN tunnel but the problem is that the two offices has a ADSL connection with dynamic IP. Is possible, with this router, to use a DDNS service to create the VPN tunnel or it' s required to have static IP ?
View 1 Replies View RelatedI am a mac user, and whenever I try to open this following link: [URL] to log in my router, nothing happens. Firefox and/or Safari browse the link for a while, but then nothing happens. I am using a Zyxel prestige series 600.
View 3 Replies View RelatedThe BT Infinity Hub (fibre optics to the cabinet one) plugs into a router and I tried connecting via ethernet cable to both without result, still no set up page from [URL] either with wi-fi off or with wi-fi on in the "Currently connected to:" window.
View 1 Replies View RelatedWe have a ZyXEL (P-2601HN-F1) router and three computers in our house. Currently, we only use cables to connect to the router because we haven't been bothered to setup wireless. However, there's a curious problem where the moment we connect more than 2 devices at a time, the router loses connection to the internet. To be precise, all LEDs are on, except wireless (d'uh) and Internet.
All involved computers run Win7.
So my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedMy ZyXEL modem/router does not detect my ethernet cables. it has one that runs to the main computer and i have a cable connected to my xbox. the light does not turn on when i try to use the internet for my xbox and the xbox does not detect ethernet. the other port works fine for the computer.
View 1 Replies View RelatedI don't know if I'm saying this right but, I have two computers in my LAN hooked up by a Ethernet cables to my modem/router zyxel pk5000z we were using theses computers to play together using Game Ranger. We were having some problems connecting to game rooms with a symmetric NAT. When the port forwarding did work it would only let me open ports for one ip adress for 1 computer it seemed. How do you open ports for all computers on your LAN?
View 1 Replies View RelatedI have one P-660HN-T1A ZyXEL wireless router at my home with 2mbps connection. ZyNOS Firmware Version: 3.40(UTU.0) my brother always keeps on downloading stuffs from bitTorrent and eats up all the bandwidth.
1. is there any way to put speed limit on each user of my wireless router??
2. or is there any way to just block torrent download on my router???
3. QOS [quality of service] setting on Zyxel router so that I make my priority higher than my brother?
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View RelatedI have a 4-port Zyxel P334U with WLAN, and I would want to set it up so that besides normal WAN, each connected computer also has access to the other local computers. I've tried setting it up before, but haven't managed to get it working, so I gave up.I have DHCP set up, beginning at 192.168.1.16. WAN and ISP DHCP works, so each computer has a local IP (192.168.1.x) and a remote IP given by the ISP.
View 6 Replies View RelatedSeveral times a day our router will lose its connection to the internet (the internet light goes off, while the wireless signal stays on). All the computers in the house lose connection to the network while this happens. It will usually happen two or more times right after each other, so the computers can re-connect for a few seconds and then the connection will drop again. Eventually, after this repeats a few times, everything returns to normal.We've tried swapping cables, microfilters and 3 different routers (though all the same model). We tried the test socket, but the same problem happens. An engineer came to test the line but said he couldn't detect any problems. We have good download/upload speeds while the router stays connected and no noise on the phone line. I'm fed up of going in circles with the ISP tech support so I came here instead...One other thing I tried was OpenDNS, but that made no difference either...
Info: The router is a ZyXEL P-660HW-T1 v3... I've tried updating the firmware on it, but it wouldn't let me... If I remember correctly the Router Configuration Interface told me I don't have permission to do that.There are four computers connected.. mine is Windows 7, I'm pretty sure 2 others are as well, and also a Macbook... There's also various stuff like an Ipad, Kindle etc., which all lose connection at the same time.
Have a ZyXEL 600 wireless router - it has worked without issues for years.However yesterday evening my wireless router suddenly stopped broadcasting a signal. 2 different PC's and a wifi dongle attached to our TV were suddenly all unable to find my network.The WLAN light on the router was still lit up. I connected my Acer Aspire 5742Z laptop to the router via an ethernet cable and it worked fine. I connected to the router and it said there were no errors.
View 14 Replies View RelatedBought the Zyxel Wireless Range Extender to get wifi in farthest rooms in my house but set up is not working because BT have disabled WPS button on Home Hub 3 with my Infinity. Therefore they suggest I try manual set up. This requires browser wtih IP address 192.168.1.2 for Zyxel wireless extender WRE2205, This gives no result (page does not load in IE).
View 1 Replies View Related