Cisco Routers :: RV082 Ssl Port Forwarding Configuration
Nov 20, 2011
I have recently replaced an RV082 router that had failed with a new RV082. The previous router was set up to forward port 443 ssl requests to a server in the network. Worked flawlessly for years and that is why I replaced it with same model. The new router is also set up to forward port 443 ssl requests to the new server. The issue is that the router responds with its own certificate and does not forward the request to the server.
View 5 Replies
ADVERTISEMENT
Apr 11, 2012
I have an RV082 V2 with 2.0.2.01-tm and I am having trouble with getting my Sprint Airvana to connect properly to the mobile service. I've read on the Sprint forums indicate putting the Airvana in the DMZ generally allows the device to work properly; however, none have the RV series routers for tips on how to do this appropriately. This device used to work fine behind the RV082, but I reset it one day and it no longer works.
The Airvana is a femtocell/router device with a WAN port and 3 LAN ports. If I connect the Airvana directly to my cable modem, I get the appropriate connection and can then make calls through the device instead of through the Sprint connection; I live in a basement unit and get crappy signal without the device. This proves the device works and that my ISP is not blocking the ports. Sprint indicates the device uses UDP 53, 67, 68, 500 and 4500. Their support sucks and they insist I put the Airvana before my router. I absolutely do not want to use the Airvana as the router. There are almost no configuration options in the router interface and it needs to be rebooted somewhat regularly, which would drop internet access throughout the house for 10-15 minutes while it reboots and finally establishes an internet connection.
As soon as put the Airvana behind the RV082, I no longer get the appropriate connection. I can, however, plug my computer into one of the LAN ports on the Airvana and connect to the internet in general. I have the router assign a static IP to the Airvana, and tried forwarding the required UDP ports to the IP. This did not fix the problem.
I can certainly troubleshoot the port forwarding issues, but I would also like to look into putting the device into the DMZ, if possible. I've not worked much in this area, so I am unsure how to appropriately configure the router to allow this to happen. Is it possible to have the Airvana in the router DMZ without having a public IP for the device itself?
View 2 Replies
View Related
Mar 22, 2012
I have found numerous posts discussing this but have yet to find a solution. I have an RV082 with firmware 2.0.0. 2.0.0.19-tm and I need a way to limit the incoming smtp traffic to just the spam filtering company.I have a port forwarding rule to forward WAN1 port 25 traffic to 192.168.1.10.I tried to add an access rule to deny all port 25 and then added one to allow WAN1 port 25 source <spam company> destination 192.168.1.10The RV082 log screen shows the traffic allowed but it does not work. If I uncheck the 'enable' box on the DENY port 25 rule email is still blocked. Only when I uncheck the 'enable' box on the ALLOW rule does email start flowing again.
View 10 Replies
View Related
Nov 15, 2012
we use RV082 as main gateway and need to open/forward around 50 ports to inside. But during setting of the rules I got an error message "The max of Port Range Forwarding is 30 entries. You can't add any more.".
In the online help is explicitely said "4. Click the Add to List button, and configure as many entries as you would like."
How can we setup more than 30 port forwarding rules ?
View 4 Replies
View Related
May 16, 2012
I'd like to setup a WCCP in those routers, but as I read, it's not possible.
Another way to circumvent this limitation is to foward a request to the router from the LAN port 80 to a LAN IP, something like:
LAN 1 192.168.1.100:80 -> router -> LAN 2 192.168.1.101:80
View 1 Replies
View Related
Jul 13, 2012
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies
View Related
Aug 12, 2012
I am setting up a SBS 2011 Essentials sever using a rv082 router. I have a decent understanding of how everything is suppose to work, but execution has been sloppy. My aim is to set up a central storage location, back up services, remote access and VPN. Yesterday I had set up dhcp and dns roles on the sever, configed port forwarding and firewall setting on the router, at that point I was just bouncing around everywhere trying to get stuff to work, clearly not the best way I know. Before I left I reinstalled sbs for a couple of reason, along with resetting the router to default.
View 1 Replies
View Related
Feb 27, 2013
Currently, the backup config is not human readable...any way to convert this?
View 1 Replies
View Related
Jun 12, 2012
RV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
View 36 Replies
View Related
Apr 2, 2013
interface GigabitEthernet0/0
ip address x.x.x.36 255.255.255.248
ip nat outside
ip virtual-reassembly in
no ip route-cache
duplex auto
speed auto
no cdp enable
[Code]
ip nat inside source static tcp 192.168.1.252 22 x.x.x.36 6922 extendable
ip route 0.0.0.0 0.0.0.0 x.x.x.33
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit any
Anything wrong with my config? port forwarding to my ssh wont work. Im using CISCO 1900 Series.
View 10 Replies
View Related
Apr 22, 2013
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
View 2 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
Apr 13, 2013
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies
View Related
Jan 6, 2013
I want to port forward, so i can broadcast using icecast but it requires me to access my router. I follow the steps from Setting a Static IP Address in Windows 7 - PortForward.com but from step 4 where i have to access my router in my browser,i write my ip which is: 10.0.0.4 according to cmd, and i just get a "Oops! Google Chrome could not connect to 10.0.0.4" message.I have attached a picture showing info from my cmd. It's in danish but i don't think that should be a problem.
View 3 Replies
View Related
May 15, 2012
I have an ADSL connection which I would like to have my Cisco Soho 97 ADSL router configured to dialup and forward to port 8080.
My network is 192.168.1.0/24
Router is 192.168.1.1
Server is 192.168.1.4 - Default gateway is 192.168.1.1
I am able to connect using the script below and get a public ip address but i cant get it to connect to the internet?what command to use for port forwarding to 8080?
hostname Router
!
!
ip subnet-zero
ip name-server 212.23.8.1
ip name-server 212.23.3.1
ip dhcp excluded-address 192.168.1.1
[code]...
View 5 Replies
View Related
Apr 23, 2012
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
!
[code]......
View 2 Replies
View Related
Mar 3, 2011
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
View 1 Replies
View Related
Jan 17, 2013
I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
View 1 Replies
View Related
Feb 29, 2012
We have a RV082 Router and we are trying to do port translation.
For example:
88.123.2.5:80>192.168.1.10:2334
88.123.2.5:81>192.168.1.10:2335
However this does not seem to be possible as I can only choose the source port and the destination IP address unlike the RVS4000.
View 1 Replies
View Related
Oct 9, 2011
I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Apr 7, 2013
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies
View Related
Feb 8, 2012
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies
View Related
Apr 10, 2012
Port forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
View 10 Replies
View Related
Apr 19, 2013
Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.
The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?
View 5 Replies
View Related
Mar 10, 2011
I', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?
View 3 Replies
View Related
Jul 7, 2011
I am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless
View 2 Replies
View Related
Aug 26, 2011
I just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.
View 4 Replies
View Related
Jan 2, 2013
I have a RV042 with Port Forwarding configured for RDP. This Port Forwarding Rule is being applied before my ACL - so subnets that are not authorized through are being allowed in. Firmware version 4.0.0.07.
View 2 Replies
View Related
Sep 24, 2011
I'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies
View Related
Aug 12, 2012
Today i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies
View Related
Aug 25, 2011
We have the following proplem with the RV 120w router with the last firmware. We can't manage to set up port forwarding. So the situation is like this: we have WAN ip: 192.168.2.68 and our router connects to VPN server and gets an IP like 10.0.10.X. In the inner network we have PCs and a DVR (digital video recorder) with ip 192.168.1.215. Our DVR uses 3 main ports like 81 (http) and 37777 (tcp), 37778 (udp) and we try to make port forwarding with the router interface like the manual says (look and the sceenshot). But when we try to enter our DVR and see the picture from the outside network (we type in browser 192.168.2.68:81) nothing happends. It just dosen't work.
Before cisco we used d-link router and everything worked just fine with the same port forwarding rules.So we need to enter WAN address in Cisco and show the 81 port in the address bar and see the picture from the DVR 192.168.1.215 from the inner network.
View 3 Replies
View Related
Sep 4, 2012
How can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
View 4 Replies
View Related
