I', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?
View 3 Replies
I'm looking for an example config of how to run dual ISPs while doing port fowarding for one of the publicly facing IPs. This is on 8.4 so
View 1 Replies View RelatedI have Cisco 2910 router that have 3 interfaces:
g0/0 - LAN
g0/1 - WAN1
g0/2 - WAN2
I would like to configure port forwarding in such way that connections to both WAN interface on identical ports will be redirected to a single host in a private network. When I issue command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/1 8080 everything is fine, until I add the second command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/2 8080
After that, the first statement is just replaced by the second one, not added to configuration.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 build 120810 Rel.44064n
ISP : BT infinity
I'm trying to portforward on my WDR4300 to use Dyndns to view my Dreambox outside of my home network.I can not seem to forward ports, is there a guide to port forwarding for this router.basically I want to forward port number 12000 to my dreambox with local ip 192.168.0.101 ( with dyndns representing 192.168.0.101)
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless
View 2 Replies View RelatedI am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.
View 1 Replies View RelatedI am trying to port forward for Vuze and I am having a problem understanding the concepts at [URL] for working within two routers. I have a Zoom 5241 cable modem connected through a Motorola VT2442-VD for Vonage VOIP, then connected through my Netgear RangeMax WPN824v3 wireless router, to my computer. I am also running AVG internet security. Here is a look at my ipconfig /all:
C:Users
ex>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : MarekFamily
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
However, I do not understand where to setup the static ips and where to drop DHCP to be able to port forward successfully. I have tried in Vuze to set up acceptable ports 51600 for TCP and UDP, but they continue to get this error: "NAT Error - Connect attempt to 67.60.124.173:51600 (your computer) timed out after 20 seconds. This means your port is probably closed." I do know that the Ip present is from my Vonage with my external IP address. I even tried to establish rules for TCP and UDP within AVG Firewall settings for the Vuze program.
When checking my port forwarding, it says that it is not open.
View 2 Replies View RelatedI have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies View RelatedI need to set up port forwarding to access a security camera from my home computer. I can't get it to work on my F5D8230-4.
View 8 Replies View Relatedhow do i do port forwarding on my belkin n750 db i want to view my cams when not home i can view on my network not tmobile?
View 3 Replies View RelatedPort forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.
The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?
I have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
View 3 Replies View RelatedPort forwarding on my linksys is not seem to be working from outside the network. It works fine if I try on the same network. External ip address: 69.117.132.xxx Ports from 8080 through 8080 forwarded Internal ip address: 192.168.1.150 - static ip address assigned to the webserver. I understand 80 could be blocked by the ISP. Can 8080 also be the same case?
View 12 Replies View RelatedWhen checking my port forwarding, it says that it is not open. Why?
View 6 Replies View RelatedI just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.
View 4 Replies View RelatedI have a RV042 with Port Forwarding configured for RDP. This Port Forwarding Rule is being applied before my ACL - so subnets that are not authorized through are being allowed in. Firmware version 4.0.0.07.
View 2 Replies View RelatedI'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies View RelatedToday i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies View RelatedWe have the following proplem with the RV 120w router with the last firmware. We can't manage to set up port forwarding. So the situation is like this: we have WAN ip: 192.168.2.68 and our router connects to VPN server and gets an IP like 10.0.10.X. In the inner network we have PCs and a DVR (digital video recorder) with ip 192.168.1.215. Our DVR uses 3 main ports like 81 (http) and 37777 (tcp), 37778 (udp) and we try to make port forwarding with the router interface like the manual says (look and the sceenshot). But when we try to enter our DVR and see the picture from the outside network (we type in browser 192.168.2.68:81) nothing happends. It just dosen't work.
Before cisco we used d-link router and everything worked just fine with the same port forwarding rules.So we need to enter WAN address in Cisco and show the 81 port in the address bar and see the picture from the DVR 192.168.1.215 from the inner network.
How can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
i have a WRVS4400N Router and behind that router i am running a OPENSWAN Server. I know that the WRVS4400N has a VPN Service on board, but for specific reasons i'd like to use my own ipsec server.
The problem is that i cannot forward the IPSEC Paketes (4500 and 500) coming from the internet interface to the LAN. All other port forwardings like SSH works. I think the reason is that the IPSEC Services (Pluto, etc.) are already running on the router and therefore the pakets cannot be forwarded. The log shows all forwarded port (e.g. SSH) but does not show any IPSEC traffic.
I'd like to turn off the VPN Service on the router, but I cannot find any configuration switch that allow my to do so.
Router: WRVS4400N
Firmware: 2.0.2.1
Background: Port forwarding external port 1234 to internal port 123 on a NAS appliance (ip 192.168.1.111) Successfully accessed NAS like this: [URL] Everything was working perfectly for several weeks Last week I changed the subnet to 172.17.888.x
Problem: Everything back to normal on the LAN except that port forwarding to the NAS no longer works.
Gerfingerpoken: I opened another port (1235) and forwarded that to the NAS (in addition to the original port). No success.
I tried a port scanner. The port scanner reported that port 1234 was open on the router, but didn't mention 1235. I repeated with yet another port. Same result: only port 1234 is reported open by the port scanner. Software rebooted the router, same result Hard reset (button) the router, still no change.
QUESTIONS:
1. How can I test if the router is actually forwarding new ports? (software tool?)
I have recently replaced an RV082 router that had failed with a new RV082. The previous router was set up to forward port 443 ssl requests to a server in the network. Worked flawlessly for years and that is why I replaced it with same model. The new router is also set up to forward port 443 ssl requests to the new server. The issue is that the router responds with its own certificate and does not forward the request to the server.
View 5 Replies View RelatedWe've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.
View 1 Replies View RelatedSome days ago I bought a new RV180W router with firmware 1.0.1.9. The router is configured with PPPoE and I need to forward some port (a basic operation for a router!!!). I try in every way but it doesn't work. My old router works well. [URL]
View 1 Replies View Related
