Cisco Routers :: RV220W Forwarding Port Range?
Sep 4, 2012
How can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
View 4 Replies
ADVERTISEMENT
Sep 24, 2011
I'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies
View Related
Mar 10, 2012
I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.
View 1 Replies
View Related
Nov 23, 2011
i have a Problem with my Cisco RV220W with the Firmware 1.0.3.5.I have in my LAN a Dreambox with the IP Adress 192.168.1.230, he listen to the Port 8880.How can I set up a port forwarding from the WAN to the Dreambox ?
View 2 Replies
View Related
Nov 26, 2011
I have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
View 3 Replies
View Related
Apr 24, 2012
I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.
View 1 Replies
View Related
Feb 1, 2012
I have a setup with 2 RV220W at 2 locations.Both with the latest Firmware (1.0.3.5). I configured portforwarding for RDP at one site. Works perfekt. I also configured an IPSec VPN between the 2 sites. Works too.
Configuration overview:
Site_1:
- IPSec VPN to site_2
Site_2:
- IPSec VPN to site_1
- Port forwarding for RDP to a local server (server_2)
My first problem is that i can ping server_2 through the VPN from a pc within site_1 but i can not access this server via RDP. As soon as i disable the Portforwarding for RDP at site_2, RDP via VPN works! I assume, that the RV220W mixes up portforwarding and VPN.I tried to set up an additional firewall rule at site_2 allowing the traffic between the local networks of both sites without restrictions and place this rule at toe top. But here is my second problem: I can not add any destination network to the firewall settings (firewall-->access rules). I only allows me to define a host to redirect the traffic to.
View 3 Replies
View Related
Apr 10, 2012
I have recently separated a few sites that I operate, into multiple virtual machines, all with their own IP.Basically, site A is located on for instance www.siteA.com, Site B is located on blog.domain.com etc etc. So my question is, how do I (with the Cisco RV220W), forward port 80 based on host?[URL]
View 3 Replies
View Related
Sep 5, 2011
I have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.
View 11 Replies
View Related
Mar 31, 2013
I'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.
View 6 Replies
View Related
Sep 12, 2011
I am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
View 4 Replies
View Related
Jul 14, 2011
Is it possible to configure the RV220W to forward ports without connecting to the SSL VPN?
View 9 Replies
View Related
Oct 30, 2012
I need to open port range 554 - 558 to a DVR on the internal network. Also, I need to NAT one of my public IP's to the DVR. How is this accomplished in 8.4? I was able to do it in an older version ASA software.
View 3 Replies
View Related
Mar 23, 2006
I’m having serious issues getting Tandberg H.323 working behind this router with NAT.
My setup is Cisco 1811 configured with Fas0 to pull DHCP (public address). This router is being used in a mobile medical clinic VAN so the setup needs to be seamless and transparent to the users. The idea with the DHCP is anywhere they go they could pull a DHCP address and then NAT behind that address. The van visits mostly small schools in the Texas Rio Grande Valley providing medical assistance and consulting to the local community. The router has an 8 port built in switch and all ports are sitting in default VLAN 1.
Basic stripped down config, only relevant commands listed…
ip dhcp excluded-address 10.0.0.1 10.0.0.4
ip dhcp pool VANnet
network 10.0.0.0 255.255.255.240
default-router 10.0.0.1
dns-server 10.0.0.1(code)
Now initially I can’t even get the call to connect with just using the ports above, which I should. Also knowing there are several issues with H.323 and NAT I went ahead and added all know ports Tandberg says they use…
80 HTTPd *TCP
443 HTTPs TCP
1719 H323/RAS UDP
1720 H323/Q931 *TCP
2326-2373 (2837)** H323/RTP UDP
5555-55xx (5587)** H323/H.245/Q.931 TCP
Basically I created static NAT entries for all the ports and the ranges above. For the ranges I had to add a line for every port.
This didn’t and hasn’t worked yet even with some additional tweaking… Finally the question… am I going about this all wrong? Is there an arrangement of commands that will even work? How can I accomplish the port forwarding setup on a Linksys/Netgear router on a real Cisco router?
View 9 Replies
View Related
Dec 5, 2012
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
View 3 Replies
View Related
Jan 21, 2013
I have a Cisco 881 router in my office and I would like to do port forward for port 5060, and 10000 - 20000 to my PABX(192.168.1.61). After I did some research from internet, understand that we need to NAT by using following command to do port forward for port 5060. ip nat inside source static udp 192.168.1.61 5060 XXX.XXX.XXX.XXX(WAN IP) 5060 extendable However, now I'm facing an issue to perform port forward for a huge range of ports like 10000 to 20000.
View 9 Replies
View Related
Jun 1, 2011
I have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies
View Related
Apr 3, 2012
I have a Cisco 881 router in my office and I would like to do port forward for port 5060, and 10000 - 20000 to my PABX(192.168.1.61).After I did some research from internet, understand that we need to NAT by using following command to do port forward for port 5060.
ip nat inside source static udp 192.168.1.61 5060 XXX.XXX.XXX.XXX(WAN IP) 5060 extendable.However, now I'm facing an issue to perform port forward for a huge range of ports like 10000 to 20000.It is impossible to ask me add one by one?
View 3 Replies
View Related
Oct 17, 2011
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
View 1 Replies
View Related
Aug 21, 2011
I have configured port range forwarding (8440 - 8449) for a single PC (192.168.1.134) and am unable to access these ports from outside my LAN. Conversely, if I set up single port forwarding for each of the ports in the range for the same computer then I am able to access from outside my LAN. Does port range forwarding actually work?
E1200 / 1.0.00 build 11 Jan 23, 2011
View 1 Replies
View Related
Oct 3, 2012
I have a WRT160n that I am trying to forward some ports on for some DVR equipment. When I use the single port forwarding and enter each port separately it works fine. But I have 2 DVR's and they use a bunch of ports each so I want to use the port range forwarding because there are not enough spots in the single port forwarding section. The ports I am trying to forward are 8000-8004 for one IP address and 8005-8009 for a second IP address. I have entered it into the port range forwarding section but I can not connect from outside my network. As I said if I enter them in the single port section seperately as 8000,8001,8002,8003,8004 then I can connect fine outside my network.
View 7 Replies
View Related
Nov 3, 2011
At the E4200 there is a limit of (free to make) 15 Single port forwarding and 15 port range forwarding to fill in.I get as suggestion that I must give up a total range of ports where all the ports I use where in.But for security reasons I will not do that.
View 1 Replies
View Related
Jan 26, 2013
I'm trying to make the server work for minecraft and I have the port number for the port which is 25565.I just need to know where exactly to enter this information. I also know that the protocol is supposed to be set for both tcp/udp.
So basically I guess my question is, where exactly do I put the port number if the one given to me was 25565?
View 2 Replies
View Related
Apr 22, 2013
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
View 2 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
Apr 13, 2013
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 13, 2011
recently got a RV220W and liking all the configuration options.
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.
View 5 Replies
View Related
Apr 7, 2013
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies
View Related
Nov 11, 2012
From an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them
[Code].....
View 2 Replies
View Related
Feb 8, 2012
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies
View Related
Apr 10, 2012
Port forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
View 10 Replies
View Related
Apr 19, 2013
Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.
The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?
View 5 Replies
View Related
