I'm trying to make the server work for minecraft and I have the port number for the port which is 25565.I just need to know where exactly to enter this information. I also know that the protocol is supposed to be set for both tcp/udp.
So basically I guess my question is, where exactly do I put the port number if the one given to me was 25565?
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
I have configured port range forwarding (8440 - 8449) for a single PC (192.168.1.134) and am unable to access these ports from outside my LAN. Conversely, if I set up single port forwarding for each of the ports in the range for the same computer then I am able to access from outside my LAN. Does port range forwarding actually work?
E1200 / 1.0.00 build 11 Jan 23, 2011
I have a WRT160n that I am trying to forward some ports on for some DVR equipment. When I use the single port forwarding and enter each port separately it works fine. But I have 2 DVR's and they use a bunch of ports each so I want to use the port range forwarding because there are not enough spots in the single port forwarding section. The ports I am trying to forward are 8000-8004 for one IP address and 8005-8009 for a second IP address. I have entered it into the port range forwarding section but I can not connect from outside my network. As I said if I enter them in the single port section seperately as 8000,8001,8002,8003,8004 then I can connect fine outside my network.
View 7 Replies View RelatedAt the E4200 there is a limit of (free to make) 15 Single port forwarding and 15 port range forwarding to fill in.I get as suggestion that I must give up a total range of ports where all the ports I use where in.But for security reasons I will not do that.
View 1 Replies View RelatedI have a Cisco 881 router in my office and I would like to do port forward for port 5060, and 10000 - 20000 to my PABX(192.168.1.61).After I did some research from internet, understand that we need to NAT by using following command to do port forward for port 5060.
ip nat inside source static udp 192.168.1.61 5060 XXX.XXX.XXX.XXX(WAN IP) 5060 extendable.However, now I'm facing an issue to perform port forward for a huge range of ports like 10000 to 20000.It is impossible to ask me add one by one?
I need to open port range 554 - 558 to a DVR on the internal network. Also, I need to NAT one of my public IP's to the DVR. How is this accomplished in 8.4? I was able to do it in an older version ASA software.
View 3 Replies View RelatedI’m having serious issues getting Tandberg H.323 working behind this router with NAT.
My setup is Cisco 1811 configured with Fas0 to pull DHCP (public address). This router is being used in a mobile medical clinic VAN so the setup needs to be seamless and transparent to the users. The idea with the DHCP is anywhere they go they could pull a DHCP address and then NAT behind that address. The van visits mostly small schools in the Texas Rio Grande Valley providing medical assistance and consulting to the local community. The router has an 8 port built in switch and all ports are sitting in default VLAN 1.
Basic stripped down config, only relevant commands listed…
ip dhcp excluded-address 10.0.0.1 10.0.0.4
ip dhcp pool VANnet
network 10.0.0.0 255.255.255.240
default-router 10.0.0.1
dns-server 10.0.0.1(code)
Now initially I can’t even get the call to connect with just using the ports above, which I should. Also knowing there are several issues with H.323 and NAT I went ahead and added all know ports Tandberg says they use…
80 HTTPd *TCP
443 HTTPs TCP
1719 H323/RAS UDP
1720 H323/Q931 *TCP
2326-2373 (2837)** H323/RTP UDP
5555-55xx (5587)** H323/H.245/Q.931 TCP
Basically I created static NAT entries for all the ports and the ranges above. For the ranges I had to add a line for every port.
This didn’t and hasn’t worked yet even with some additional tweaking… Finally the question… am I going about this all wrong? Is there an arrangement of commands that will even work? How can I accomplish the port forwarding setup on a Linksys/Netgear router on a real Cisco router?
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
View 3 Replies View RelatedI have a Cisco 881 router in my office and I would like to do port forward for port 5060, and 10000 - 20000 to my PABX(192.168.1.61). After I did some research from internet, understand that we need to NAT by using following command to do port forward for port 5060. ip nat inside source static udp 192.168.1.61 5060 XXX.XXX.XXX.XXX(WAN IP) 5060 extendable However, now I'm facing an issue to perform port forward for a huge range of ports like 10000 to 20000.
View 9 Replies View RelatedHow can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
I am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
I have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies View RelatedI am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies View RelatedI use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
View 9 Replies View RelatedI'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
View 5 Replies View RelatedI am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies View RelatedMy first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
View 1 Replies View RelatedI recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
View 2 Replies View RelatedI'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies View RelatedIm going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable
I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit.
View 1 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedI set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 Replies View RelatedIm trying to open up some ports on my e3000 for the use of Teamspeak and my Teamspeak server. However when i get of the information filled into the single port forwarding under the Gaming & Applications tab, and click save settings. The page just refreshes, with none of the changes being saved.
View 6 Replies View RelatedI am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Linksys E1200 Router not saving Port Forwarding changes.I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding
IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
I upgraded to a 6500 from a e4200. I use ports 81-84 on test web servers set to static Ip,s when I open the ports nothing can get through from the outside. I can hit the pages internally on those ports and IP's but not from my external ip to those ports. When I set my old router everything is fine.
View 9 Replies View RelatedHow to forward a single port to a different port to a specific computer for the WRV210 router?
I would like to forward port 10100 to port 25 to my mail server. There are times when our people are at a hotel and they block port 25 and I have done this in the past on a BEFSR11 and BEFSR41 router. There does not seem to be a Single Port Forwarding setup page and the Port Forwarding setup page only allows you to forward a range to a specific computer, it does not give you a different port you can assign an incoming port to.
I have the most current firmware revision, 2.0.0.11, and Hardware Version WRTR-221G_V01.