Linksys Wireless Router :: WRT54G - Port Forwarding Setup
Feb 12, 2012
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies
ADVERTISEMENT
Mar 30, 2013
I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies
View Related
Oct 12, 2011
i have a 54G wireless home router ..... successfully port fowarded an application from a CPU (server).... but after no connection made from the user to the server..... it suddenly close the application ..... so what i did is to reboot the router in order to refresh the connection ...... Is there any other ways to fix this sudden close of the ports ?
View 9 Replies
View Related
Jan 24, 2013
I have a WRT54G Linksys router and I am wondering what is the default username and password for port forwarding?
View 1 Replies
View Related
Mar 14, 2013
Trying to setup port forwarding for an XBox 360. Set fixed IP on XBox using IP outside DHCP range. DHCP range is .50 to .80. Set XBox to .49. Gateway is .1. Mask is 255.255.255.0.Added four port forwarding rules per directions on xbox site and also portforwarding.com for ports 53, 80, 88, 1074 to the static IP Turned off DMZ, Turned off UPnP, Turned off SPI. Windows firewall is on, running XP Pro SP3 and Win 7 Pro on other devices.Making the rules active for the fixed IP shuts off internet access for other devices.Single router (E4200 V2), switch, then remaining devices. Private IP addresses in the 192.168.xxx.xxx range. Rebooted router, same issue. What am I missing?
View 9 Replies
View Related
Nov 11, 2011
Port forwarding on my linksys is not seem to be working from outside the network. It works fine if I try on the same network. External ip address: 69.117.132.xxx Ports from 8080 through 8080 forwarded Internal ip address: 192.168.1.150 - static ip address assigned to the webserver. I understand 80 could be blocked by the ISP. Can 8080 also be the same case?
View 12 Replies
View Related
Mar 2, 2012
I need to setup some port forwarding on my X3000 to pass through the firewall to my server but cannot find the relevant page in the setup GUI.
View 2 Replies
View Related
Dec 25, 2011
I'm finally jumping in over Christmas break to set up a Y network with three routers. I run a side business repairing and cleaning viruses/malware from PCs and would like the business subnet not to be able to mix with (and possibly infect) the "home" subnet.Before I knew what I was doing, I set up a simple two router "chained" network by hanging an old SMC router off my main Airport Extreme router, but I've since learned that's not ideal, since the "work" network machines can see everything on the "home" network. So, here's what I want to do. I want to put the new third router right after my cable modem (ISP). I want to keep my Airport Extreme and all devices attaching to it (home subnet) off one LAN port of this new router and my old SMC router off another LAN port of the new router (the test subnet). Currently, the IPs are: [code]My concern in setting up a "Y" configuration is that I have some wireless IP webcams on the Airport Extreme that are using port forwarding (both UDP and HTTP) so I can view them from wherever I am on the Internet, not just from within my home network.
What's the best way to make sure the port forwarding from devices on the Airport Extreme subnet works through the "new" router and out through to the Internet? Do I have to open the same ports on the new router? If so, does anyone have an example using the addresses above? Should I just put the Airport Extreme in the DMZ of the new router (so everything is just passed through - or will that allow my test subnet to see the home subnet? Some other way?
View 2 Replies
View Related
Jul 21, 2012
I have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies
View Related
Jan 14, 2013
I just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
View 14 Replies
View Related
Jan 2, 2011
My ISP is centurylink and I have a 660 series modem that is both a modem and a router (no wireless). Also I have a Linksys WRT54G v3 wireless router with Tomato Firmware on it. For whatever reason I can't get the port forwarding to work. Yes, I know I have to forward the ports on both and I have tried using this guideurl...Fowarding.php on the modem, with Tomato Firmware it is super simple to forward.
View 13 Replies
View Related
Jan 31, 2011
I've got a pretty simple setup where port forwarding was working without a hitch.My old router (wrt54g) was forwarding RDP requests (over 3389) to my computer's ip. No problems. Then I switched it out with a WRT160N wireless router (and upgraded firmware), and I just can't seem to make the connection.
I've followed all the simple tutorials, ala:
[URL]
Still no luck...! I've ensured my ip is the one the router is pushing connection attempts to, dropped firewall and filtering... still nothing (I've even tried connecting from within the network, using my computer's name) without any success.
View 3 Replies
View Related
Oct 1, 2012
I have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies
View Related
Apr 13, 2012
I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
View 5 Replies
View Related
Jun 7, 2012
my mother in law thought she forgot her wifi password so i tried to do a reseti reset it then no internet at all and could not access the router gateway page (192.168.1.1)I had to set the internet protocol to default and 2 power cycles later i can access the internet.Then i used the linksys disc to set up the security and now it doesn't work can't access nothing through ie.
View 1 Replies
View Related
Jan 19, 2013
I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.
View 9 Replies
View Related
Dec 4, 2011
I have a Linksys Router that shows WRT54G Ver 3 on its base, but when I go in the settings I realized it says WRT54GL over there.
View 1 Replies
View Related
Feb 27, 2009
I have lost my installation disk for my WRT54G Version 8. Where I can download the drivers and installation.
View 9 Replies
View Related
Jul 18, 2011
I have wrt54gl setup with dd-wrt standard version running hotspotsystem. 3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl. After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load. I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work. Is it the load on the router made it inaccessible ?
View 1 Replies
View Related
Sep 8, 2012
I wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies
View Related
Apr 27, 2012
When I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?
View 3 Replies
View Related
Jun 26, 2012
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies
View Related
Feb 26, 2013
I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
View 9 Replies
View Related
Sep 16, 2011
I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
View 5 Replies
View Related
Nov 2, 2012
I am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.
View 9 Replies
View Related
Nov 2, 2012
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies
View Related
Feb 6, 2013
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
View 2 Replies
View Related
Nov 1, 2009
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
View 9 Replies
View Related
Aug 31, 2012
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
View 1 Replies
View Related
Jan 19, 2012
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
View 1 Replies
View Related
Jan 28, 2012
I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
View 2 Replies
View Related
Nov 14, 2012
Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable
View 1 Replies
View Related
Jan 23, 2013
Region : Australia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0
Build 120926 Rel.27100n
ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
View 2 Replies
View Related
