Linksys Wireless Router :: Wrt54gl And Wrt54g Setup WDS But Can't Login
Jul 18, 2011
I have wrt54gl setup with dd-wrt standard version running hotspotsystem. 3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl. After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load. I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work. Is it the load on the router made it inaccessible ?
View 1 Replies
ADVERTISEMENT
Dec 4, 2011
I have a Linksys Router that shows WRT54G Ver 3 on its base, but when I go in the settings I realized it says WRT54GL over there.
View 1 Replies
View Related
Jan 11, 2013
I am using a wrt54gl in 'Router' mode. It is behind a server that is configured as a server/router/firewall that is serving dhcp addresses for the network behind it. I have bypassed the dhcp server hardware by plugging the LAN out from my server/router/firewall into a switch port on the back of the wrt54gl. I have switched off the dhcp server in the wrt54gl during it's configuration.how can I login to the wrt54gl to review and make note of its current configuration ?
View 3 Replies
View Related
Aug 8, 2012
Which of these model numbers have the greatest range?
A: WRT54G
B: WRT54GL
C: WRT54GS
View 1 Replies
View Related
Jan 21, 2013
I am unable to login to my router ? I have tried to reset my router and am still unable to login to the online control panel. The steps that I went about resetting the router were pushing the reset button for 30 seconds. That did not work so I pushed the reset button for 30 seconds, unplugged the router while continuing to hold the reset button for 30 seconds, plugged the router back in while holding the reset for 30 seconds.
View 6 Replies
View Related
Sep 18, 2012
I want to use a linksys router with a 3com switch. 3Com model 3CGSU08A.i have two routers to choose from a E2000 and a WRT54GL which one is better and settings to use.
View 1 Replies
View Related
Sep 18, 2012
How to add a Linksys router for wireless access to a 3Com switch. model 3CGSU08A I have two choices for routers E2000 and a WRT54GL which one would be best and how to setup?
View 1 Replies
View Related
Oct 6, 2011
I've run into this before, but I can't figure it out this time. Running Windows XP SP3 on a Dell Vostro 1510 notebook with a Linksys WRT54G router wireless. Using Dells Network Assistant for management, so I cannot get to Windows wireless connection management directly.I have a connection to the internet with a Security Key. When I bring up a browser (Firefox or IE) I cannot resolve to a web site. There is a Cisco login screen that is forced. It's from a previous wireless connection on a different network at a different location.
View 1 Replies
View Related
Oct 30, 2012
I have a Cisco network at my office and the router and everything is set up under my desk.I can use the internet just fine on my office computer but I am trying to use it on my laptop and login to the guest account .I ran across the Cisco Connect sofware and that I need it to find the password but the problem is I dont think I have a router or whatever it is that is compatible with this software I am using WRT54g wireless n router, the models on the site for the cisco connect are e series
View 1 Replies
View Related
Mar 29, 2008
I have a Linksys WRT54GL version 1.1. The firmware is 4.30.11 (European version).In the Basic Wireless Settings I can't change the Wireless Channel. It remains at channel 1, and I simply can't alter it.This is strange, because in earlier firmware versions, I was able to change the channel without any problems at all. I would like to continue to use this firmware version. How can I solve this problem?
View 9 Replies
View Related
Apr 6, 2010
I'm trying to setup a DVR camera system and two web page server boxes behind a Linksys WRT54GL. The problem I have is that all of the devices want to use port 80 to generate the web page. Individually, I can get the boxes to work, but when I try to put it all together everything seems to fall apart. I've got to the DVR set to External port 80, Internal Port 80 IP address 192.168.1.254. The web page server box I try to set to External port 8001, Internal port 80, IP address 192.168.1.200, when I try to save this setting I get the error message Internet IP address and LAN IP address are in the same subnet. If I change the web page server settings to External port 8001, Internal port 8001, IP address 192.168.1.200, it will save the settings, but it won't work that way because it won't actually generate a web page when I try to access that port.The error message doesn't seem to make since as all I'm changing is the port number, not the IP address or subnet mask.
View 9 Replies
View Related
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Mar 8, 2013
I am using 3G to access the internet on my PC. I have a 3G modem connected, and want to setup my Linksys WRT54GL router to enable wi-fi, so other devices can access the internet as well.
View 7 Replies
View Related
Oct 1, 2012
I have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies
View Related
Apr 13, 2012
I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
View 5 Replies
View Related
Feb 12, 2012
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies
View Related
Jun 7, 2012
my mother in law thought she forgot her wifi password so i tried to do a reseti reset it then no internet at all and could not access the router gateway page (192.168.1.1)I had to set the internet protocol to default and 2 power cycles later i can access the internet.Then i used the linksys disc to set up the security and now it doesn't work can't access nothing through ie.
View 1 Replies
View Related
Jan 19, 2013
I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.
View 9 Replies
View Related
Feb 27, 2009
I have lost my installation disk for my WRT54G Version 8. Where I can download the drivers and installation.
View 9 Replies
View Related
Sep 8, 2012
I wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies
View Related
Apr 27, 2012
When I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?
View 3 Replies
View Related
Jan 22, 2011
Linksys WRT54GL I need access to my router, but the default password and usernames do not work. I think hitting the reset button and holding it would set everything back to default, but will EVERYTHING but reset to default or just the password?
View 2 Replies
View Related
Apr 27, 2007
When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
View 3 Replies
View Related
Jan 14, 2008
I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
View 9 Replies
View Related
Feb 2, 2007
I'm trying to setup a Linksys wireless-g router model number WRT54G with my DSL connection. I followed the basic instructions that came with the router and towards the end of the process it says detecting network settings with a % bar. The bar fills to 100% and then asks for a password. I've tried the password my DSL company gave me along with various other things like admin etc. After I enter the password I hit enter and it just asks me for the password over and over again.
View 9 Replies
View Related
Aug 17, 2011
how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
View 1 Replies
View Related
Aug 5, 2011
I am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).
View 5 Replies
View Related
Dec 8, 2012
Cannot connect to Linksys Router 192.168.1.1 Webpage, do not get login setup screen.
View 1 Replies
View Related
Jun 17, 2007
I've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies
View Related
Dec 25, 2011
I assign private IP for each PC within LAN. And DHCP is in charge of wireless connection since 192.168.0.100 for 10 clients. ,Web setup access is also disable for wireless connection.When a notebook connect to WRT54G via wireless. Private IP is always out of range and it could accesses web setup.What happen to my WRT54G ?
View 3 Replies
View Related
Sep 1, 2011
On a BEFVP41, I disabled snmp for testing (because it was sending some strange alarms), and now I can't login to the web setup pages. The username and password no longer work. I thought maybe it reset itself to default (blank/admin) but it didn't.
View 1 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Jan 3, 2013
I have a WRT54G V8 and everyone says the username to sign is is blank and the password is admin. I have tried this and it does not work. I have also reset the router several times and this also does not work.
View 2 Replies
View Related
