Linksys WRT54GL I need access to my router, but the default password and usernames do not work. I think hitting the reset button and holding it would set everything back to default, but will EVERYTHING but reset to default or just the password?
View 2 RepliesI recently installed an RE1000, which seemed to be working fine. Then, on 3 PC's with no wireless adapter installed we began being prompted for user name and password for the wireless router. Once I unplugged to extender the problem went away. I know what you're thinking: Maybe I just think there's no wireless adapter on these PC's. NO, I looked in device manager and the only network adapter installed is the ethernet adapter. These are all 4+ year old machines with no hardware changes made to them. Wireless adapters are not necessarily standard issue on old towers--even on new towers. The Acer I'm using right now was purchased new in November 2011 and did not come with a wireless adapter installed.
View 3 Replies View RelatedI am using a wrt54gl in 'Router' mode. It is behind a server that is configured as a server/router/firewall that is serving dhcp addresses for the network behind it. I have bypassed the dhcp server hardware by plugging the LAN out from my server/router/firewall into a switch port on the back of the wrt54gl. I have switched off the dhcp server in the wrt54gl during it's configuration.how can I login to the wrt54gl to review and make note of its current configuration ?
View 3 Replies View RelatedI have wrt54gl setup with dd-wrt standard version running hotspotsystem. 3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl. After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load. I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work. Is it the load on the router made it inaccessible ?
Is there a way to reset the device and start all over again. The person who set this up is no longer with the companyand did not detail the information. We installed a new t1 line with new IP addresses and need to set this to connectwith our remote location. And I am not knowledgeable at all on how to configure this.
View 1 Replies View RelatedWe have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View RelatedI am having problems trying to connect to my wi-fi. I first noticed that I had problems connecting to some types of unsecured wi-fi connections when I was "borrowing" from my neighbour while I waited for telus to install my internet. My two roommates would have no problem surfing but my computer was unable to get any connection to the internet (i could see the connections but never load a page)
Once telus came and installed the internet I was able to get a "fair" connection to the router and surf with decent speeds. About a week after I first started using the internet, my computer started being unable to connect the router. It seems that everything is getting worse and worse. It started by me having to restart the adapter a couple of times to make it work, to me having to delete the network profile and then redo it, to me only being able to connect by using the WPS.
And now my computer can't even get the information from the router through WPS! I would start to point the finger at telus, but every one of my roommates has no problems connecting to the internet, and it's not a range issue (i'm typing this up with my laptop while sitting beside my desktop).
I have a prob with my laptops,wireless setup although it shows wlan on it will not work without a connection to the router,netgear wgr614,I have gone into Devise Mng and found the following faults,Serial cable IRDA problem code 43 & SRTSPX code 24 not working.
View 1 Replies View RelatedI currently set up two LAN networks. But one of them (Router 2) will be open (no password). Will this create a security compromise? Can the Router 2 Users access information of users of Router 1?
Modem WAN > Router 1 WAN
Router 1 LAN > Router 2 WAN
The router 1 and 2 are broadcasting different networks and SSID.Is there any setting that I need to change, or this configuration is perfectly safe? both of them have DHCP enabled.
How do you find Clearwires ISP information to set up older 2.4 router?
View 1 Replies View RelatedI have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
I have a Cisco 2610 series router(Version 12.0(5)T1, c2600-i-mz.120-5.T1), which has a network module inserted. I would like to view the model of this network module. There are no "show inventory" or "show platform" commands. "Show version" doesn't list the network module as well. In addition, it appears to have a "show c2600" command, but this doesn't display any hardware information.
View 14 Replies View RelatedMy desktop pc is currently wired into myowireless router and my laptop is fully wireless. How do I send data(pictures,music etc) from my laptop to my desktop & vice versa?
View 1 Replies View RelatedWhere I can bookmark a page with information on the Re-call of this router?I am pretty sure that this router is not under a re-call yet but after the endless amounts of discussions and problems folks have had with this thing it has to be recalled soon right?I don't want to loose faith in DLink products because like many I have owned them for years and years. A bad release is going to happen sooner or later but if the company does nothing about the problem it is time to move to a new brand.
At the very least when is the next firmware version going to be released? I have tried them all and none of them seem to work. I am well past the stage of troubleshooting because the problems I have like Way to many other people are not being solved by discussions and firmware changes or altering settings.
My site is thinking of using AP 2600 instead of the trusty AP 3502 since it has better thru put. Any experience on 2600 as we want to ensure stability for our deployment.
View 4 Replies View RelatedIs there any small router model (like 1941) that can be ready for future 4G LTE?
View 1 Replies View RelatedNo changes made but router will lose all information for IPv connectivity. I have paid twice to support to fix this issue and it still occurs every few months. I tried rebooting router, and doing an IP Release/ Renew and router does not get IP address.
View 4 Replies View RelatedI'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
I just buy a simple hub and keep my wrt54gl as my router or should I put the money toward a wireless N router (or AP) for the better range and use the wrt54gl as my hub?I currently have my wrt54gl as my one and only router.It gives me good range indoors, but I would prefer to get better range outside, if possible. Right now I get range out about 50 feet around the outside of the house but I would prefer that to double, if not more.At the same time, however, I need to move the router to the basement to better facility my network. Obviously, this will affect the wireless range.I have considered DD-WRT, but not sure it will work much from the basement.So, I have considered two options.One, I could keep my router where it is and just get a simple hub and stick it in the basement.Obviously this is the least expensive option, but it doesn't improve the current router's range, although I could try DD-WRT. The other option is I could use the money I would put toward the hub and, instead, upgrade to a wireless N router or AP and move the wrt54gl to the basement to serve as my hub.
View 8 Replies View RelatedRecently we ordered a new Modem from Centurylink to replace an old one we have. (which ironically the old one's wireless is way better) Both modems work perfectly fine, and I've tried the same things with both to figure this out. I ran an ethernet to my gaming room, which is about 150 feet. When I connect my computer directly into the modem, my computer works fine. Initially, the PS3 worked, but when I switched back to the computer with the single Ethernet cable, I was getting an IP error. Every since then, the PS3 will not connect through Ethernet. (Wireless works, but its so far away the signal is weak)
So, I dug up my router, Linksys WRT54GL, plugged it into the ethernet that came from the Modem, (did all the steps in order multiple times), and no internet through wifi or ethernet on it. The lights and everything say there is ethernet and the WIFI/Ethernet are working, but there is no internet. All the wires are confirmed fine. I've tested them on other devices plugged directly into the modem. I tried the PS3 at the modem with 3 Ethernet cords as a test, It says there is an IP Address timeout error. Regardless of what I do, the PS3 won't connect via Ethernet. And without internet working on the Linksys router, Im getting about 15-25% signal from the Modem. (which is also wireless, if that has anything to do with the issue)
I need the router to do at the very least, WIFI. I really want Ethernet though so I don't lose much speed. (We are maxed out here at 1.5mb connection from Centurylink)
When it comes to computers, I'm advanced with them. When it comes to networking, I'm okay. I understand basic things, like accessing the router or modem through the browser. I can do the whole setup for WIFI. But when it comes to how the IP address, Static IP, etc., goes, im confused by them. So forgive me if I sound ignorant. I've looked for over a week on sites, and nothing is working. The router may be broken, im not sure. I bought it a few years ago and then didn't need it till recently. So its been sitting in a box.
All I know is, I have an ethernet from the modem to this room, the PS3 refuses to get an IP, and if I do it too much the PC gets an IP conflict. If I plug the Ethernet into the internet part of the router and do wireless or Ethernet, there is no internet coming out.
In our house we use a Linksys WRT54GL router. When I am connected to the router via a cable I can play an online RPG without any problems.I recently connected an acecss point to the router ( a belkin N1 ). Even if I am connected with a cable to the accesspoint, which is connected to the router by cable as well, I get huge lag spikes about every 10 seconds while playing the game.
View 10 Replies View RelatedFew months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
I have both a Sony XBR52HX909 and a Sony BDP-S580 connected to my router (WRT54GL)via ethernet. When I try to connect to the internet, both show the wired connection as good but neither can connect to the internet. The BDP-S580 also has wireless connectivity, but it can’t connect to the internet wirelessly. I have two desktop computers connected via ethernet and two laptops connected wirelessly to the same router and all have internet connectivity. I have tried the “auto” settings on the TV and Blu-Ray player and also tried entering the network information in manually. I still can’t connect to the internet.
View 5 Replies View RelatedLast week suddenly my internet connection failed. I have tried several times to establish the wireless internet connection. Everytime when i tried to do this, i get the message 'can not get IP address'. Already tried to upgrade the firmware but still same message appears.
View 4 Replies View RelatedI want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies View RelatedI have Wireless-G Broadband router Model WRT54GL. Everything is all setup correct but consoles and handhelds can't get the IP address even if there connected to the router. It isn't intill I turn off and then it back on does it get the ip address.
View 2 Replies View RelatedI have a WRT54GL that I bought about 2 months ago, and I've had nothing but problems with the wi-fi since I started using it. It works as normal about 90% of the time, but usually 50+ times per day, I won't be able to connect to the router wirelessly (with ANY device, no matter how close I am to the router) for 1 to 2 minutes. The fact that I can't connect to the router with ANY devices during these times leads me to believe that the problem lies with the router itself. Another thing to note is that the wired connection to the router works just fine during these wireless outages.
I've tried changing channels and upgrading the firmware, but nothing has changed. Did I just get a bad router?
I'm trying to use a WRT54GL with U-Verse. The problem is that the router does not get a connection to the modem. It can't ping the modem, and it doesn't show up on on the list of devices connected to the modem. DHCP assigns an IP address of 127.0.0.1, which is outside the range of the modem [192.168.1.1 ... 192.168.1.253]. The router is also showing a default gateway of 0.0.0.0, and a subnet mask of 255.0.0.0. (And yes, I have released and renewed the lease, rebooted the modem, and reconnected the modem.) The router WAN side is set to DHCP, and the operating mode was changed from gateway to router (the gateway setting doesn't work either, for that matter).
View 9 Replies View RelatedAny issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).
I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.
Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?
I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies View RelatedI've been looking around for quite some time and can't find a complete answer. I have a Linksys WRT54GL router handling my home wireless network located in the living room (let's call it 'Zone A').I have an ethernet cable running from that router to the other end of the house (let's call this one 'Zone B'), where the wi-fi signal is very weak. a. What is the technically correct way to have a strong wi-fi signal at Zone B (with the same SSID, key-phrase, etc.)? b. If I take another WRT54GL router, set the same SSID and key-phrase, disable its DHCP and plug it to the ethernet cable in Zone B - will that do the trick? I've tried the Linksys range extender at a friend's house and it turned out to be a big flop.
View 3 Replies View RelatedI recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies View Related