Home Network :: WRT54GL Router Range Extending?
Apr 13, 2012
I've been looking around for quite some time and can't find a complete answer. I have a Linksys WRT54GL router handling my home wireless network located in the living room (let's call it 'Zone A').I have an ethernet cable running from that router to the other end of the house (let's call this one 'Zone B'), where the wi-fi signal is very weak. a. What is the technically correct way to have a strong wi-fi signal at Zone B (with the same SSID, key-phrase, etc.)? b. If I take another WRT54GL router, set the same SSID and key-phrase, disable its DHCP and plug it to the ethernet cable in Zone B - will that do the trick? I've tried the Linksys range extender at a friend's house and it turned out to be a big flop.
View 3 Replies
ADVERTISEMENT
Dec 11, 2012
how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies
View Related
Jul 1, 2011
I have Linksys WRT54GL wireless router on the top floor so the devices in one part of the bottom floor (most away from the source) are having trouble staying connected let alone getting good connection. What would be good solution in my case? I'd like something wireless, don't want to drag cables downstairs.
View 2 Replies
View Related
May 7, 2013
I have been using the Wireless G broadband router WRT54GL for about a year now. Recently we bought HP laserjet network printer which is connected to the domain network with the ip range of 10.1.1.1 which is the same network linksys router is connected to. Since router always lease different range of ip (192.168.1.1) then all computers connected through router cannot print because they are in different network/ip range.is there a way allow wireless user to print to the same printer regardless of the ip difference?
View 5 Replies
View Related
Feb 8, 2013
Sending WiFi signal about 1/4 mile from my home to where my daughter lives so she can use her Samsung Galaxy2 Tablet on WiFi.There are homes, condos and trees in between us, so it is not a clear path.So far this is what I have done.I am using a modem and a Netgear WNR834B Wireless N Router.I connected a Hawkins Laptop Extender (HWREN Wireless 150N Mini Extender * single antenna outlet) into the router and connected a WiFi cable from the Hawkins to my tower outside above my roof and have attached a 10 dbi gain Trendnet antenna (omnidirectional) to the cable.But still the WiFi signal doesn't seem to be very strong at all when I test with my phone.And obviously, my daughters tablet does not see my router when she has her tablet search for WiFi.I also tried a 14dbi WIfi ASUS directional antenna and basically came up with the same outcome... she could not see the WiFi signal..My daughter lives in a condo and is not capable or allowed to install any outside antenna system whatsoever.
View 2 Replies
View Related
Jul 24, 2011
I am wanting to buy an access point to extend my range on my home network. I think i've used one AP before and if i remember correctly, after i plugged it into my main rounter and configured it, i unplugged the ethernet from it and moved it to somewhere else in the house. But i can't remember for sure if this is how it works or do i have to have an ethernet cable running to it at all times?
View 10 Replies
View Related
Mar 18, 2012
Recently we ordered a new Modem from Centurylink to replace an old one we have. (which ironically the old one's wireless is way better) Both modems work perfectly fine, and I've tried the same things with both to figure this out. I ran an ethernet to my gaming room, which is about 150 feet. When I connect my computer directly into the modem, my computer works fine. Initially, the PS3 worked, but when I switched back to the computer with the single Ethernet cable, I was getting an IP error. Every since then, the PS3 will not connect through Ethernet. (Wireless works, but its so far away the signal is weak)
So, I dug up my router, Linksys WRT54GL, plugged it into the ethernet that came from the Modem, (did all the steps in order multiple times), and no internet through wifi or ethernet on it. The lights and everything say there is ethernet and the WIFI/Ethernet are working, but there is no internet. All the wires are confirmed fine. I've tested them on other devices plugged directly into the modem. I tried the PS3 at the modem with 3 Ethernet cords as a test, It says there is an IP Address timeout error. Regardless of what I do, the PS3 won't connect via Ethernet. And without internet working on the Linksys router, Im getting about 15-25% signal from the Modem. (which is also wireless, if that has anything to do with the issue)
I need the router to do at the very least, WIFI. I really want Ethernet though so I don't lose much speed. (We are maxed out here at 1.5mb connection from Centurylink)
When it comes to computers, I'm advanced with them. When it comes to networking, I'm okay. I understand basic things, like accessing the router or modem through the browser. I can do the whole setup for WIFI. But when it comes to how the IP address, Static IP, etc., goes, im confused by them. So forgive me if I sound ignorant. I've looked for over a week on sites, and nothing is working. The router may be broken, im not sure. I bought it a few years ago and then didn't need it till recently. So its been sitting in a box.
All I know is, I have an ethernet from the modem to this room, the PS3 refuses to get an IP, and if I do it too much the PC gets an IP conflict. If I plug the Ethernet into the internet part of the router and do wireless or Ethernet, there is no internet coming out.
View 1 Replies
View Related
Mar 22, 2012
I want to share my pc's wifi connection with a neighbor across the street. But i have been un-able to confirm that it can reach the net. With the configs i have tried.I have cloned the mac addy for the wifiAP i have shared. This should be enough. And i should be able to walk it across the street and have it act as the same wifiAP. And he should have the net, via my pc. I tried to use another wifi device to connect to the shared IP...And the router itself...But there was no internet. have tried to configure this router to work as a repeater as well using it's setup. This resulted in no internet connectivity over lan, and no wifi service listing. These is no way for me to tell it which router or device it should be repeating from...
I have tried manually configureing the mn-700 To use the same ip the other router does for it's services. The mn-700 doesn't keep the settings. When it does there is no internet or wifi services.When i have it setup on it's own, no config changes...It'll connect over wifi to the router but there is no net. I can connect a lan wire going to the other router and renew it's lease. This will give the mn-700 an ip addy as if it were another pc. It uses this as it's WAN config
View 4 Replies
View Related
Jul 10, 2011
My wireless router in my downstairs office won't reach an upstairs bedroom on the other side of my house. I'd like to extend the range. It is not clear if my best option is to get an antenna to boost the range (such as an Alfa 500mW AWUS036H USB Wireless Adapter 802.11 b/g Network Radio Card. Includes 2dBi Omni Antenna ), or to get a repeater to repeat the signal, such as a Hawking HWREN1 Hi-Gain Wireless-300N Range Extender. I also don't know if Linksys has a product for either application that works with 802.11n standard.Finally, since the Linksys E2500 has no antenna or antenna port visible, I am nod sure if an antenna such as the Alfa listed above or a Hawking HSB2 HiGain Signal Booster would even work with the E2500.
View 3 Replies
View Related
May 8, 2012
have a home network setup that works completely fine everywhere in the house except one room. That room happens to be my son's room that has his Xbox 360 in it. He wants to play online but I cant get a signal back in there and if I do it is extremely weak. I have a linksys E2500 router connected to my cable modem that is wired ot one computer and then my 2 laptops connect to the wireless from that router. The Playstation 3 that is about 15 feet away works fine as well. All our ipods and iPhones work well too. It is only his bedroom where we run into trouble with any of these devices. I actually just upgraded to the E2500 about 2 months ago, so I have a Motorola WR850G sitting around. Can I use this closer to his room to lengthen my signal or how can I proceed to get him a better signal
View 2 Replies
View Related
Jan 17, 2013
I have an AirPort Express set up as my router, and that works fine and is the main network that I use. I also have a Linksys WRT54GL that is wired to a printer.Currently, when I want to print from my computer, I have to manually connect to the Linksys network, which is a pain. I would like to wirelessly connect the Linksys to my main network, so I can print even when connected to my Airport Express.Does that mean that I have to configure the Linksys as an access point? A bridge? Something else? How do I do that?
View 8 Replies
View Related
Mar 30, 2011
We currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
View 10 Replies
View Related
Dec 27, 2012
I am trying to determine the best option for extending my home network. I am currently running an E2000 as my router and am considering the purchase of a Valet Plus to use as only an Access Point. Alternatively I have a used E1000 in good condition. Which would be best for use as an Access Point only?
View 1 Replies
View Related
Jul 26, 2011
Just purchased WRT54GL for family friend to extend the wireless range of their DSL via 2Wire ATT modem Wireless router. One desktop computer will stay wired to the 2Wire and laptop or 2 will connect to the WRT54GL since the 2Wire cannot reach into the yard (metal buiding). I've seen several examples of connecting two WRT54G together. I Can I do that well with std Linksys software or would I be better off downloading Tomato or DD-WRT third party?
View 1 Replies
View Related
Jun 14, 2011
I have a newer N Router (Dlink DIR-655) and the wireless signal coming off of it, just isn't strong enough. I was planning on using the WTF54GL to repeat the signal and inturn increase the coverage area. I've installed the latest version of Tomato on there (v1.28) and have gone through setting it up as a wireless client, wireless ethernet bridge (which works for picking up the wireless signal and then plugging something in via ethernet has internet), access point, access point + wds and just wds. None of which I can get to seem to properly repeat the wireless signal with internet connectivity. I have both routers set to G only channel 6, WPA Personal, Is this even possible? Or do I need a router that can run the tomato firmware on the main (host) router that is connected to the net?
View 1 Replies
View Related
Oct 26, 2008
I've got a WPA wireless network set up that utilizes a total of 4 WRT54GL routers as access points (on channels 1, 6, and 11 [the two APs furthest from each other both utilize 11). Each AP generally supports about 5 clients at a time (though sometimes as high as 10).Generally, everything is working, but the clients furthest from the access points occasionally lose their connections, and some users have reported periods when they are completely unable to obtain an IP. I am virtually certain that this is based on poor signal strength resulting from distance from the APs and/or RF interference from other APs in the building. I have done everything possible to improve signal strength by router placement, optimizing channel usage based upon RF surveys, and upgrading to high-gain omnis.
This leaves nothing to do apart from tweaking the advanced wireless settings to marginally improve problems related to weak signal and/or RF interference, so I've been reading everything I can find on these boards and elsewhere about changing Fragmentation Threshold, RTS threshold, and beacon interval. However, I'm left with the following questions.
1) There seems to be disagreement about Fragmentation threshold and RTS threshold settings. Some (including the Linksys Technical Troubleshooting Wizard) recommend that both be set to 2304. I have also seen people insist that Fragmentation be set to 2306 and RTS to 2304. A few recommend 2306 for both thresholds, and some advise 2306 for Fragmentation and 2307 for RTS (though by my limited understanding, it simply disables RTS when the value is higher than the fragmentation threshold value). Which of these settings is best? And more importantly, WHY is it the best? Generally, I understand what the settings do, but I am reluctant to change them when there doesn't seem to be a consensus about exactly what they should be.
2) With respect to beacon interval, I've seen both 75ms and 50ms recommmended to replace the default of 100ms. For a network of my size (4 APs, averaging 5 users each), will increasing the number of beacons (and hence the RF traffic even when the network is idle) pose a problem? Also, I'm a little less clear as to how this would improve connectivity.
Since these settings will affect all users, I want to make sure that I'm using settings that will be beneficial on the whole. The last thing I want to do is inadvertantly make things worse, and since I can't test things directly from the standpoint of each user.
View 4 Replies
View Related
Aug 8, 2012
Which of these model numbers have the greatest range?
A: WRT54G
B: WRT54GL
C: WRT54GS
View 1 Replies
View Related
Jun 3, 2011
I'm an electrical engineer by trade, and fairly inept at networking. That being said, I am looking to extend the maximum range of my networking equipment. I have a job which requires around 500' between switches, and am trying to find a clever way to bridge the gap. The span is direct-burial cat5e, and has very low bandwidth requirements. I know you can buy off-the-shelf range extenders, but they are expensive, so I thought maybe I could avoid it.
1. It my understanding that the lower speed protocols (10 Mbps rather that 100, 1000) have a longer maximum operating length, because they utilize a lower frequency and consequently see a lower impedance. If so, are there network switches that I can force to use the lower baseband frequencies?
2. Should I bother trying to find a cable with the lowest characteristic impedance (or will they all be similar)? Cat 5e is pretty good, yes?
3. Should I do half or full-duplex; is this something I can control as well?
4. What network switches are cheap and allow this type of configurability?
5. If I attach other switches to the ends of this 500' ethernet bridge with auto-negotiating feature, will there be any conflicts or they will all get along?
View 12 Replies
View Related
Aug 19, 2011
In a bit of a predicament. We're from Ireland and we've two houses on the farm that are exactly 108m as the crow flies. The main house is where we live and the other is more of an office type small house. We've no phone line or internet connection in it and the location is in a dip where we've bad mobile/cell connection. We're don't want to pay an extra55 a month for phone line and internet just to use the internet maybe twice a week. We have a wireless connection in the main home house and want to extend it to the other. I know there are ways but confuesed as to which to use.
View 3 Replies
View Related
May 14, 2012
We've got an SA520W that's performing nicely, but we need to extend our wireless coverage to a new area of the building (we can get a network cable there). What would be our best option? Just a second SA520W, or are there are APs we should look at?
View 7 Replies
View Related
Sep 8, 2012
want to get internet and video signals from mu log home to my pole barn -- about 150 - 175 feet.
View 4 Replies
View Related
Aug 16, 2012
Extending Range of my wifi with > D655 >> Booster Amplifier?I am looking to extend my WIFI signal to cover 50 Acers.I currently have 35� height tower with Dir-655 in box with 3 big Omni directional Antennas. It works but covers half of 50 Acers and it is slow.I am thinking of buying 802.11b/g/n 2.3W Wifi Booster Amplifier.
View 9 Replies
View Related
Nov 23, 2012
Can I connect a Belkin N450 wireless router to a Belkin N750 wireless router without using a cat5e cable?
View 1 Replies
View Related
Sep 25, 2011
I want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
View 2 Replies
View Related
Dec 17, 2011
I am using a WRT54GL for the free wifi service at my business. Is there any way to set it so that when someone accesses the internet they are directed to my business home page first?
View 1 Replies
View Related
Mar 5, 2011
I am trying to set up a WAP4410n Wireless access point and add to my home network. One problem I can't seem to get around. The IP adress range setup does not accept 1 (example 192.168.1.245) as a range setup for IP address. How do i get in communication with the unit when I can't view the setup due to the factory default set as 192.168.1.245? If it were 192.168.0.245 I could easily change my routers IP range to include it.
View 0 Replies
View Related
Jun 4, 2011
I have a RVS4000 and a WRT54GL router at home... I am planning to power down my home completely for several hours, my question is will I have to re-setup everything or will it retain the settings within the router?
View 6 Replies
View Related
Dec 30, 2012
I am using the HTC One S and a Linksys WRT54GL router and I find that I become out of range once I leave the room with the router. I am wondering if there is some sort of setting that I need to change on the HTC One S or Linksys WRT54GL to make the signal stronger?
My brother owns a Moto Razr, dad has HTC Desire C, friends have iPhone, S3, Nexus 3... all do not have any problems with our wifi connection anywhere in our house. In addition, I'm able to bring my 8 year old laptop across the street and use our wifi on our neighbour's lawn.
View 3 Replies
View Related
Apr 29, 2013
I live in a house with three floors. I have a Virgin Media Superhub on the ground floor with the 30MB package. Whilst the wireless signal quality and speed is good on the ground and first floor, it is intermitent on the second floor and my son wants to connect his PS3 with a wired connection for speed.
I have a N wireless router that I was using before I receiced the new Virgin Superhub. I want to ask if I can connect the old wireless router in my son's room on the second floor and connect it with a Cat5e ethernet cable to the Superhub on the ground floor. This way, I will have a wired connection on the ground floor for my desktop computer, my son will have a wired connection for his PS3 and laptop and his own wireless network.
I just want to know if this will work with an ordinary cable wireless router? Or do I need some sort of special access point? If this will work, do I connect the cable from the Superhub to the WAN port of the old router, or to one of the four other ethernet ports?
View 5 Replies
View Related
Jan 17, 2013
Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies
View Related
Jul 25, 2012
As my original Innbox V50U modem/router does not have a strong enough wifi signal I had to add in an additional wifi router - I used a Cisco Linksys E4200.The problem is that if I connect my laptop to the cisco router I can see the Innbox router but not vice versa. There is an additional problem as I have a wireless printer that is connected to the Cisco router. If I connect to the Innbox router I cannot use this printer as I cannot see its IP address.I read somewhere it might be down to the subnet mask. both are set to 255.255.255.0Apologies if this is n00b stuff but I have not had this problem before, I just naturally though the two networks would be able to talk to each-other.
View 1 Replies
View Related
Oct 31, 2012
I have a DIR-655 router downstairs on one side of my home. Upstairs on other side of my home wireless signal is really hit and miss. I do have ethernet in the area of my home where I am wanting to extend the signal. Is there a device I can plug into the ethernet to extend my wireless signal without creating a new network or ssid?
View 4 Replies
View Related
May 11, 2011
I have a Linksys e3000 and a Linksys WRT120NVery simple setup. the 3000 is in my office. There is a cable that goes from this routerto the living room across the house, it is just laying there. Since I cannot get a wireless signal into that room,I would like, using the cable that is hanging there to make use of the other linksys and provide a wireless signal to the living room, all under the same network. In essence, extending the wireless network using the cable in the living room that is connected to the main router in my office.My question is, without touching the master router, how would I set the 2nd router in the living room up?I understand that DHCP on the 2nd router needs to be turned off, and a channel selected so that it does not overlap. Same SSID, Sam WPA2 key.Or would there be a device better suited for this?I do not want to extend the 2 rooms wirelessly I want to use the cable, then use the wireless in the living room for wireless devices etc.
View 9 Replies
View Related
