Belkin Routers :: N450 - Extending Wifi Range?
Nov 23, 2012Can I connect a Belkin N450 wireless router to a Belkin N750 wireless router without using a cat5e cable?
View 1 RepliesCan I connect a Belkin N450 wireless router to a Belkin N750 wireless router without using a cat5e cable?
View 1 Replieshave purchased Belkin wifi usb adapter dualband N450 and downloaded the driver from included CD, my OS is windows7 starterfter I plug in the adapter, the power ON is litting and wait for a while if will flashing but not. I opened the "NETWORK AND SHARING CENTER" and click the "CHANGE ADAPTER SETTINGS", the Belkin wireless adapter is disabled and had tried enabling it but still it is disable. I uninstalled the driver and the program, I checked in the internet and downloaded the file F9L1101v1_N600.exe and installed. Checked again but still the same problem before, Disabled and tried enabling but to no success.
View 3 Replies View RelatedI want to share my pc's wifi connection with a neighbor across the street. But i have been un-able to confirm that it can reach the net. With the configs i have tried.I have cloned the mac addy for the wifiAP i have shared. This should be enough. And i should be able to walk it across the street and have it act as the same wifiAP. And he should have the net, via my pc. I tried to use another wifi device to connect to the shared IP...And the router itself...But there was no internet. have tried to configure this router to work as a repeater as well using it's setup. This resulted in no internet connectivity over lan, and no wifi service listing. These is no way for me to tell it which router or device it should be repeating from...
I have tried manually configureing the mn-700 To use the same ip the other router does for it's services. The mn-700 doesn't keep the settings. When it does there is no internet or wifi services.When i have it setup on it's own, no config changes...It'll connect over wifi to the router but there is no net. I can connect a lan wire going to the other router and renew it's lease. This will give the mn-700 an ip addy as if it were another pc. It uses this as it's WAN config
Can N600 DB Wi-Fi Range Extender have the exact same name as my N600 DB Router or does the extender have to have the additional characters "_xt" at the end of the extender name, when the first part matches the router name?
View 1 Replies View RelatedSending WiFi signal about 1/4 mile from my home to where my daughter lives so she can use her Samsung Galaxy2 Tablet on WiFi.There are homes, condos and trees in between us, so it is not a clear path.So far this is what I have done.I am using a modem and a Netgear WNR834B Wireless N Router.I connected a Hawkins Laptop Extender (HWREN Wireless 150N Mini Extender * single antenna outlet) into the router and connected a WiFi cable from the Hawkins to my tower outside above my roof and have attached a 10 dbi gain Trendnet antenna (omnidirectional) to the cable.But still the WiFi signal doesn't seem to be very strong at all when I test with my phone.And obviously, my daughters tablet does not see my router when she has her tablet search for WiFi.I also tried a 14dbi WIfi ASUS directional antenna and basically came up with the same outcome... she could not see the WiFi signal..My daughter lives in a condo and is not capable or allowed to install any outside antenna system whatsoever.
View 2 Replies View RelatedExtending Range of my wifi with > D655 >> Booster Amplifier?I am looking to extend my WIFI signal to cover 50 Acers.I currently have 35� height tower with Dir-655 in box with 3 big Omni directional Antennas. It works but covers half of 50 Acers and it is slow.I am thinking of buying 802.11b/g/n 2.3W Wifi Booster Amplifier.
View 9 Replies View RelatedMy Belkin N450 assigns a 192.168.169.2 for an IP address. This does not allow me to add to the DMZ to bypass firewall and open my NAT. It wants a 192.168.2.__. What do I need to do to make this happen?
View 1 Replies View RelatedCan I Connect The Belkin N450 Router If I Don't Have A Modem? I Want To Use It To Connect My Ipod Touch to Wi-Fi.
View 2 Replies View RelatedNewer router purchased in Sept. 2012, can't get laptop connected to it.
View 1 Replies View RelatedI am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View RelatedBelkin N450 Router. I want to restrict Internet access completely but allow LAN access to a shared drive for a particular computer on my wireless network. I have gone into the web based set up page and under access controls have enabled and added this computer to the list. I have blocked http, https, ftp and nntp. I don't know if this is enough. The reason I am asking is that I am in Iraq right now and I want to allow my fellow team members access to the wireless for using viber on their iphones but one cat even though he has hardwired internet wants to continuously suck off my wireless for his computer to download stuff since I paid for faster internet. I am trying to do this quietly and still allow him access to the shared drives on the LAN. Sooooo If I block him just outright will he still have access to the drives or do I need to pick and choose like I did above and if I need to pick and choose did I miss anything other then pop3 email and imap?
View 2 Replies View RelatedThis model is FK91105v1. It is great with our ten different devices (possibly even a dozen?), but it continues to disconnect a Kindle Fire - that used to connect with no problem - evidently upon acquisition of a newer Kindle Fire. As long as MAC Filtering is not enabled, then there shouldn't be an issue of a "white list" - which the Kindle manual suggests as a solution ("If ... filtering is enabled, ensure your Kindle's MAC address is added to your router's white list in your network settings"). (I did figure out how to go to the network address, but was mostly flumoxed from there)
View 2 Replies View RelatedWithout my N 450 router hooked up I am getting hardwired speeds of 50/5 mb, but with N 450 hardwired into my PC the speeds drop to 20/5 mb. I have checked DHCP and I am not getting piggy backed. Is it a bottlekneck, misconfigured or just not compatible with Time Warner?
View 1 Replies View Relatedi have no access to my laptop keyboard, it crashed but i still need to use router for my roku and nintendo wii, however my isp has a captive portal.
View 1 Replies View RelatedIt took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies View RelatedCan I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View RelatedYesterday, I installed the N450 DB and it was probably the easiest install I've ever had to do. One problem though, I can now no longer send or receive email thru Outlook Express 6. Keep getting this message 'The host 'mail' could not be found. Please verify that you have entered the server name correctly. Account: 'mail', Server: 'mail', Protocol: POP3, Port: 110, Secure(SSL): No, Socket Error: 11001, Error Number: 0x800CCC0D'.
View 3 Replies View RelatedWill a Belkin N450 DB F9K1105 v1 work with Linksys PoE PLEK400 adapters?
View 1 Replies View RelatedI have a N450DB wireless N Router model number F9K1105 and I'm connected to the internet with an occasional interuption. The light on the front of the router is blinking orange and I have reset it and powered it down several times with no luck. According to my settings I have the newest firmware and all updates have been performed.
View 3 Replies View RelatedRouter interface for N450 DB fails to load/loads slowly/loads partially. I am running Windows 8, and have tried IE10 both from Start Screen and desktop, no luck.
View 4 Replies View RelatedHow to change my NAT type from moderate to open for xbox 360. Belkin n450 dual band
View 1 Replies View Relatedhow to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies View RelatedI have my buffalo N450 router working great and have installed a Belkin 600HD as a wired WAP. Now I am trying to fine tune them to get the greatest coverage and throughput. What do you guys recommend in terms of channel selection. Should I try to cover different channels with each router or keep them the same? I have been using inSSIDer to try and watch the strength and width of various settings. It seems I get better strength (at least according to Windows 7) when I have the channels set the same.
View 4 Replies View RelatedI have an Echolife router, HG532, connected as my main router. It is connected using cable and I use it for wifi too. The signal in other rooms is very weak and I was wondering if it's possible to use a spare router that I have, Echolife HG521, to extend the network coverage?
View 1 Replies View RelatedI have a Belkin F6D4230-4 Enhanced N150 router. Would it be advisable to add a range extender to hit weak signal areas or simply upgrade to a more powerful router?
View 1 Replies View RelatedI have Linksys WRT54GL wireless router on the top floor so the devices in one part of the bottom floor (most away from the source) are having trouble staying connected let alone getting good connection. What would be good solution in my case? I'd like something wireless, don't want to drag cables downstairs.
View 2 Replies View RelatedI have a Belkin NF5D8236-4 v3 as my main router. However, the signal range isn't the best throughout my home. After a little research and a tight budget, my thought is to purchase a Belkin N150 F9K1001 to serve as the primary router and then use the N F5D8236-4 v3 as an access point elsewhere in the house.I understand that the N150 cannot serve as an access point (hence the idea to use that as the primary), but that the N F5D8236-4 v3 can. Am I correct? Will my plan work? I can't spend much and a booster would cost more than the N150.
View 1 Replies View RelatedI have a N300 router I would like to put in another part of my house to repeat the signal from my N600 at the other end of the house. Is this possible? If so, how do I set up the N300?
View 2 Replies View RelatedI just purchased the Belkin Range Extender F9K1106 - During set up I am suppose to go to a website belkin.range - the site does not work or exist. I am unable to complete set up now.
View 1 Replies View RelatedI have a Netgear N900 WDR4500 Dual Bank Router. Which range extender should I use for the best result?
View 1 Replies View RelatedCan I set up n600 db F9K1102v1 as wifi range extender with no rj45 cable?
Dont have cable infrastructure in section of building where i need net access.
Have a Cable/Modem (wireless) as main router and need to extend the signal using the N600DB - but without cat5 cable between modem/router & N600.
I'm an electrical engineer by trade, and fairly inept at networking. That being said, I am looking to extend the maximum range of my networking equipment. I have a job which requires around 500' between switches, and am trying to find a clever way to bridge the gap. The span is direct-burial cat5e, and has very low bandwidth requirements. I know you can buy off-the-shelf range extenders, but they are expensive, so I thought maybe I could avoid it.
1. It my understanding that the lower speed protocols (10 Mbps rather that 100, 1000) have a longer maximum operating length, because they utilize a lower frequency and consequently see a lower impedance. If so, are there network switches that I can force to use the lower baseband frequencies?
2. Should I bother trying to find a cable with the lowest characteristic impedance (or will they all be similar)? Cat 5e is pretty good, yes?
3. Should I do half or full-duplex; is this something I can control as well?
4. What network switches are cheap and allow this type of configurability?
5. If I attach other switches to the ends of this 500' ethernet bridge with auto-negotiating feature, will there be any conflicts or they will all get along?
In a bit of a predicament. We're from Ireland and we've two houses on the farm that are exactly 108m as the crow flies. The main house is where we live and the other is more of an office type small house. We've no phone line or internet connection in it and the location is in a dip where we've bad mobile/cell connection. We're don't want to pay an extra55 a month for phone line and internet just to use the internet maybe twice a week. We have a wireless connection in the main home house and want to extend it to the other. I know there are ways but confuesed as to which to use.
View 3 Replies View Related