Belkin Routers :: N450 - Blocking Internet But Allowing LAN Access?
Nov 16, 2012
Belkin N450 Router. I want to restrict Internet access completely but allow LAN access to a shared drive for a particular computer on my wireless network. I have gone into the web based set up page and under access controls have enabled and added this computer to the list. I have blocked http, https, ftp and nntp. I don't know if this is enough. The reason I am asking is that I am in Iraq right now and I want to allow my fellow team members access to the wireless for using viber on their iphones but one cat even though he has hardwired internet wants to continuously suck off my wireless for his computer to download stuff since I paid for faster internet. I am trying to do this quietly and still allow him access to the shared drives on the LAN. Sooooo If I block him just outright will he still have access to the drives or do I need to pick and choose like I did above and if I need to pick and choose did I miss anything other then pop3 email and imap?
Installed new N600 router and every box in the house can access the internet - except for my Vista powered laptop. My network shows up as Unidentified network with 'locla only' access. Ben scouring message boards all day. Can't find a solution at Microsoft.
I have a N450DB wireless N Router model number F9K1105 and I'm connected to the internet with an occasional interuption. The light on the front of the router is blinking orange and I have reset it and powered it down several times with no luck. According to my settings I have the newest firmware and all updates have been performed.
My Belkin N450 assigns a 192.168.169.2 for an IP address. This does not allow me to add to the DMZ to bypass firewall and open my NAT. It wants a 192.168.2.__. What do I need to do to make this happen?
This model is FK91105v1. It is great with our ten different devices (possibly even a dozen?), but it continues to disconnect a Kindle Fire - that used to connect with no problem - evidently upon acquisition of a newer Kindle Fire. As long as MAC Filtering is not enabled, then there shouldn't be an issue of a "white list" - which the Kindle manual suggests as a solution ("If ... filtering is enabled, ensure your Kindle's MAC address is added to your router's white list in your network settings"). (I did figure out how to go to the network address, but was mostly flumoxed from there)
Without my N 450 router hooked up I am getting hardwired speeds of 50/5 mb, but with N 450 hardwired into my PC the speeds drop to 20/5 mb. I have checked DHCP and I am not getting piggy backed. Is it a bottlekneck, misconfigured or just not compatible with Time Warner?
It took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
Yesterday, I installed the N450 DB and it was probably the easiest install I've ever had to do. One problem though, I can now no longer send or receive email thru Outlook Express 6. Keep getting this message 'The host 'mail' could not be found. Please verify that you have entered the server name correctly. Account: 'mail', Server: 'mail', Protocol: POP3, Port: 110, Secure(SSL): No, Socket Error: 11001, Error Number: 0x800CCC0D'.
Router interface for N450 DB fails to load/loads slowly/loads partially. I am running Windows 8, and have tried IE10 both from Start Screen and desktop, no luck.
After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
I have an RV110W running firmware version 1.0.1.6 and I am trying to figure out how to enable website blocking in the Internet Access Policy screen. The Add Row button is grayed out in that section, as are the associated checkboxes.
Is there something else one needs to do to enable this feature?
If I set a name etc. at the top, and click save, it tells me "You must at least set a website blocking or PCs rule," so it is not the case that one has to save some information before continuing!
have purchased Belkin wifi usb adapter dualband N450 and downloaded the driver from included CD, my OS is windows7 starterfter I plug in the adapter, the power ON is litting and wait for a while if will flashing but not. I opened the "NETWORK AND SHARING CENTER" and click the "CHANGE ADAPTER SETTINGS", the Belkin wireless adapter is disabled and had tried enabling it but still it is disable. I uninstalled the driver and the program, I checked in the internet and downloaded the file F9L1101v1_N600.exe and installed. Checked again but still the same problem before, Disabled and tried enabling but to no success.
I have the following: redundant ASA5520s on v8.2(1)proxy server/web filter for blocking access to websites for staff/studentsusers who want to use SkypeCisco Catalyst 4507 corea dozen VLANs for staff/student/WiFi etcCisco core policy that routes 80/443 to transparent proxy on a WiFi VLAN Windows desktops have direct proxy settings in IE .Pretty much all outbound ports are closed with 80/443 and a handful of specifics for various things open. Because of this Skype attempts to use 80/443 which are sent to the proxy server but bnecause they're not HTTP/HTTPS they cannot be understood. Skype attitude is to open 1024-65535 which is just plain stupid!
There's no way to specify which port(s) Skype uses for outbound. I tried opening 33000-33099 which worked perfectly for 2-3 devices (Win laptop, iPad) but others failed all the time.I've seen people mention using an AIP-SSM module in the ASA for blocking Skype (and other things eg torrents). Is it possible to use this module to allow Skype eg on ports 1024-65535 whilst blocking any other application from using those ports?
My N300 Wifi Range Extender does not let me connect to Internet. I can access other systems connected on the main WIfi network, but I cannot access Internet.I observe as well that all systems connected to the Extender appear, from the main Wifi network, having the same Mac address. I believe that my ISP (Telenet) does not accept that, and that this is the reason I cannot connect to Internet. Is there any way to change that behaviour ?
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
I just bought the 655, mainly for school/Xbox. My parents use it also, but I bought it for myself mainly (shh). I set it up correctly and got connected, but suddenly I wasn't allowed Internet access. The router connects to my laptop, but won't get Internet access. I called customer service and he didn't know what to do. We tried everything he knew and nothing worked. I don't want to return the router cause I read it was very good, but I need internet for school. I have Rev. A and F/W 2.00.
How to configure Belkin N (F5D8636-4) Client IP Filtering so that a range of client IP' deny access to the internet using the following blocked time ranges e.g. Mon 5:00pm to Tues 2:00pm, Tues 5:00pm to Wed 2:00pm, Wed 5:00pm to Thur 2:00pm, Thur 5:00pm to Fri 2:00pm, Fri 5:00pm to Sat 10:00am, Sat 1:00pm to Sun 10:00am, Sun 1:00pm to Mon 2:00pm - BTW - this access regime is to deny internet access for my teenage son?
My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.
I'm a college student working on a lab involving a Cisco PIX 501 Firewall.
My project involves 1 computer and a firewall. My goal is to use the firewall to allow access to the internet for that computer which uses a static IP 192.168.1.5 and ONLY for that IP address. The firewall is connected to the internet.
I have the computer hooked up to the firewall with the serial and using hyper terminal to enter commands. I think I need to use access lists in order to deny traffic on those ports for those particular hosts. I can't figure out exactly how I need to set it up.
What I need to do is permit internet access for 192.168.1.5 alone. Any other IP should not be able to access the internet.
I tried:
access-list 1 permit tcp host 192.168.1.5 any eq 80 access-group 1 in interface inside
I cannot access the internet using the computer with 192.168.1.5. The goal is to be able to access with that IP and no other.
How to successfully block access to Instagram with the ISA550W? Also, have you experienced any significant latency with URL filtering and AV protection enabled?
We have had our router and remote computers set up with Quick VPN for over a year. We've had our share of problems but have worked around them.
Now, out of the blue, no one can connect to the VPN. I went in to try to do some 'troubleshooting' and the ONLY thing that allows our VPN connection to go through is to completely disable the RV016 firewall. We have too many remote users to actually start and stop the firewall everytime someone needs the VPN connection.
I have 5508 controller in my lab. I am working on a project to set up a public internet but with some condition.
- User should able to connect to the SSID without any authentication.
- Once user will connec to the SSID it should redirect to an external URL which indicates terms and condition and email address field.
- User should enter his/her email address in email addrss filed and click I accept button.
- Once that is done then he/she is allowed to access internet.
We are not sure how can we achive this as I do not know what should be the return value for WLC to allow that user to go through or what should be the settings on the WLC to redirect to the page.
I have seen a settings on web authentication for external URL but I guess it is only for username passwor or Radius authentication. While in this case I do not want to use any authentication just an accept buttor or Decline button and all good to go.
Every time I turn on my PC I find I have lost internet access. I can fix this by going to Network Connections, disabling the connection, re-enabling the connection.But why does this happen? I notice the the following:1. When I look at the Network Connection it shows "Local Area Connection, Network 3, Unidentified network, Realtek PCIe....."2. When I re-enable the network AVG tells me the Firewall settings have changed - Directly Connected to Network has been set to Unidentified..... etc