Cisco WAN :: 1941 - Small Router And LTE 4g Connection / Information
Jan 18, 2011Is there any small router model (like 1941) that can be ready for future 4G LTE?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Small Business SG-200 - How To Obtain SFPs Information
May 1, 2013I need to extract the serial numbers of SFPs which are plugged in a SG-200-18.For information, SG-200 doesn't have a CLI ... only a Web GUI.I just find this information : [URL]
View 2 Replies View RelatedCisco WAN :: 2901 How To Separate DNS Information For Each Connection
Jan 12, 2011Basically I am trying to do a bit of a clean up at work and replacing two dlink (home style) ADSL modems with a single Cisco 2901 router with 2 ADSL HWICs. On top of this I want to isolate the 2 connections from each other, that is I don't want to use them as fail-over or anything just as 2 seperate connections. To do this I am using VRF tunnels.So far I have been successful in the global config of the switch and everything works. And when I put the lan, atm and dialer interface into my VRF it connects up all fine.My issue that I am having is that DNS (which is being pulled from the ISP via ppp ipcp dns) seems to just populate the global dns view, not the view I created for the VRF. This results in DNS queries not being able to be resolved but all other traffic is fine (i.e. I can ping and access anything on the net, I just can't resolve names).
If I have 2 ADSL connections, on two VRF tunnels, how can I seperate their DNS information for each connection/VRF tunnel? especially if that information is different as they overwrite the global DNS config each time they connect.... I could (and have successfully tested) statically assigning DNS servers to each DNS view but I would rather rely on each ISP sending their DNS servers as opposed to me hard coding them.
Cisco Routers :: Small Business Pro Srp527w Loosing Connection
Oct 29, 2012The router keeps loosing connection to the internet. I can still log into the router locally but cant connect out or in from the internet. Which is a big problem as i use this device remotely. I have tried different firmware (.9, .19, .27) the .19 seems to be the most stable but i am still having problems. The only way to rectify it is to reboot the router. Is there a fix for this or a way to schedule a reboot on the router.
View 2 Replies View RelatedCisco WAN :: How To Configure ADSL2+ Connection With 1941
Jan 24, 2013cofigure a ADSL2+ Conexion in an 1941 router.line protocol are up but didn't have ip adresse in my interface.[code] i don't know how i can find the probleme, and debug's comandes no show me anything.
View 3 Replies View RelatedCisco Infrastructure :: 1941 / Analog Line Connection Failing?
Jul 10, 2012I have a 1941 Cisco router with WIC-!AM-V2 card that is uning pots( regural phone ) line for data traffic.the problem I am having is the line is establishing connection but it intermittently dropos.The router is configured to dial to Centraal office and I have more that 100 other locations with the same setup that are working fine. The only differene on htis one is it is going thru a PBX line.
View 1 Replies View RelatedCisco VPN :: 1941 - Unable To Make Secure Connection With Server?
Sep 5, 2012i now learning about SSLVPN, and i already install license in 1941 with SSL and security9 License, i learning how to make a gateway for SSLVPN full tunnel, but i meet an obstacles, when i go to my wan ip address https://wan ip address, the browser give this
SSL connection error Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have.
Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error
[code]...
Cisco WAN :: 1941 And SonicWall Routers - Support For 20MB Internet Connection
Oct 26, 2011I am doing a comparative between cisco and sonicwall routers. Which router would better fit me? i need it to support at least a 20MB internet connection in a datacenter and has to have a firewall included. I was thinking about a router 1941. What do you think ?
View 1 Replies View RelatedLinksys Cable / DSL :: Retrieving Up-time / DSL Connection Time Information From WAG320N
Jan 17, 2012Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedComputer Can't Even Get Information From Router Through WPS
Oct 1, 2012I am having problems trying to connect to my wi-fi. I first noticed that I had problems connecting to some types of unsecured wi-fi connections when I was "borrowing" from my neighbour while I waited for telus to install my internet. My two roommates would have no problem surfing but my computer was unable to get any connection to the internet (i could see the connections but never load a page)
Once telus came and installed the internet I was able to get a "fair" connection to the router and surf with decent speeds. About a week after I first started using the internet, my computer started being unable to connect the router. It seems that everything is getting worse and worse. It started by me having to restart the adapter a couple of times to make it work, to me having to delete the network profile and then redo it, to me only being able to connect by using the WPS.
And now my computer can't even get the information from the router through WPS! I would start to point the finger at telus, but every one of my roommates has no problems connecting to the internet, and it's not a range issue (i'm typing this up with my laptop while sitting beside my desktop).
Information About Router - Netgear Wgr614
Feb 12, 2012I have a prob with my laptops,wireless setup although it shows wlan on it will not work without a connection to the router,netgear wgr614,I have gone into Devise Mng and found the following faults,Serial cable IRDA problem code 43 & SRTSPX code 24 not working.
View 1 Replies View RelatedCan Users Of Second Router Access Information Of First One
Apr 1, 2012I currently set up two LAN networks. But one of them (Router 2) will be open (no password). Will this create a security compromise? Can the Router 2 Users access information of users of Router 1?
Modem WAN > Router 1 WAN
Router 1 LAN > Router 2 WAN
The router 1 and 2 are broadcasting different networks and SSID.Is there any setting that I need to change, or this configuration is perfectly safe? both of them have DHCP enabled.
Cisco :: View Hardware Information Of 2610 Router?
Jan 6, 2012I have a Cisco 2610 series router(Version 12.0(5)T1, c2600-i-mz.120-5.T1), which has a network module inserted. I would like to view the model of this network module. There are no "show inventory" or "show platform" commands. "Show version" doesn't list the network module as well. In addition, it appears to have a "show c2600" command, but this doesn't display any hardware information.
View 14 Replies View RelatedCisco Wireless :: AP2600 Experience And Information Of Router
Nov 29, 2012My site is thinking of using AP 2600 instead of the trusty AP 3502 since it has better thru put. Any experience on 2600 as we want to ensure stability for our deployment.
View 4 Replies View RelatedLost Login Information On WRT54GL Router
Jan 22, 2011Linksys WRT54GL I need access to my router, but the default password and usernames do not work. I think hitting the reset button and holding it would set everything back to default, but will EVERYTHING but reset to default or just the password?
View 2 Replies View RelatedFind Clearwires ISP Information To Set Up Older 2.4 Router?
May 19, 2012How do you find Clearwires ISP information to set up older 2.4 router?
View 1 Replies View RelatedSending Information From Laptop To Desktop Through Wireless Router
Jan 30, 2011My desktop pc is currently wired into myowireless router and my laptop is fully wireless. How do I send data(pictures,music etc) from my laptop to my desktop & vice versa?
View 1 Replies View RelatedD-Link DIR-655 :: Where To Bookmark Page With Information On Recall Of Router
Dec 29, 2010Where I can bookmark a page with information on the Re-call of this router?I am pretty sure that this router is not under a re-call yet but after the endless amounts of discussions and problems folks have had with this thing it has to be recalled soon right?I don't want to loose faith in DLink products because like many I have owned them for years and years. A bad release is going to happen sooner or later but if the company does nothing about the problem it is time to move to a new brand.
At the very least when is the next firmware version going to be released? I have tried them all and none of them seem to work. I am well past the stage of troubleshooting because the problems I have like Way to many other people are not being solved by discussions and firmware changes or altering settings.
New Router For Small Server?
Dec 8, 2012My father has a small office at home with a server, used to store some files and software he uses and provide a stable network for the house. The network looks something like this:
-Our wall socket line runs to a modem we have from our ISP
-The modem then is connected to our server computer
-Which is in turn connected to a switch
-...where the computers and a router are connected to
This was set up by some computer company. Now for the question: we have used the router connected to the switch to connect wirelessly to the server to receive emails on our mobile phones (email runs via the server too). Also, my father syncs his Outlook diary on his phone this way. Apparently this doesn't work when connected to the modem, I guess because that signal hasn't been processed by the server yet. Now we are unable to connect to the router, presumably because it is quite old and ready for a replacement.
The question is: Can I just replace it with some random router and expect it to work? Or do I need a more specific router/more specific settings in the router to make this work again?
Cisco WAN :: Small Site Multihoming 892 Router
May 22, 2012I'm trying to make multihoming on cisco 892 router.I Managed to build configuration which works as I wanted but I ran into problem which I can't solve till now.I'm trying to do port forwarding on cisco with 2 working WAN interfaces.
Configuration:
interface FastEthernet8
description ISP_B
ip address 192.168.150.10 255.255.255.0
ip nat outside
[Code]...
Cisco Switching/Routing :: 857W - Cannot See Any Logging Information From Router To Syslog Server
May 5, 2013I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
Linksys Wireless Router :: EA4500 Loses IPv4 And IPv6 Information?
Dec 21, 2012No changes made but router will lose all information for IPv connectivity. I have paid twice to support to fix this issue and it still occurs every few months. I tried rebooting router, and doing an IP Release/ Renew and router does not get IP address.
View 4 Replies View RelatedCisco Routers :: RV082 Small Business Router / Wake On Lan
Dec 18, 2012I saw older discussions over WOL and RV082/RV042. As router blocks broadcast packets from internet to lan, to make WOL work, i should change router's ARP table using telnet, probably with V1 and V2 versions this action was possible, but trying telnet connection (http://<Router IP Address>/ sysinfo123.htm?ConsoleSimulation=1 with RV082 V3 nothing appears, and telnet connection on standard port (23) fails.
How to make pass WOL magic packets through a RV082 V3 from internet to LAN ? Using simply port forwarding don't work, as router discard broadcast packets incoming from internet.
Cisco Routers :: RVS4000 / Affordable IOS Small Business Router?
May 24, 2012I currrently have the RVS4000 and am looking at the RV180, but I'm having an issue with the RV180 supporting the Dynamic DNS service I need (see here). In that discussion, it seems what would be ideal for me is a router running IOS so I could customize the Dyanmic DNS client on there to fit my needs. However, is there any "affordable" router running IOS that's similar to the RV180 tailored to a small business without getting an overkill router?
Here's my basic needs:Router either compatible with DNS Made Easy's Dynamic DNS service OR has the ability to customize the Dynamic DNS client on there so I can adapt it for DNS Made Easy.I DO NOT need wireless. We only need Ethernet/wired.I prefer Gigabit Ethernet.We're not currently using ProtectLink, so if it offers the ability for it, great, if not, fine.We have our own VPN service and don't need to access the network remotely (just remote into one device using Dynamic DNS), so if it has built-in VPN, great, if not, fine.I'd like IPS included. Our RVS4000 has it and I like this feature.We're switching to cable broadband and VOIP through our cable company, so QoS should probably be included.
Netgear Wndr3700v3 Router - Constant Small Lag Spikes
Jun 3, 2012I've been having this issue with my wireless connection for quite a few months now and up until now I've just dealt with it. With the release of Diablo 3 (whoo!) it's become unbearable with this lag spikes. My ping will be fine, steady around 50-90 but then randomly spike upwards of 400. After a few moments (literally a second or two) it'll drop back down to it's normal speed. This happens in all online games I play, WoW, League of Legends, DotA 2 and now Diablo 3, I have roadrunner and pay for 25 download and 1 upload so it should be more than enough to play the games I'd like, I'm also running on windows 7. I think part of the problem could be the fact that the router is in the basement and I'm on the second story. I have a netgear wndr3700v3 router and I set up a repeater in my room to see if that would work (asus rt-n12 router) and although it has increased my speed, I still have these ping spikes.
View 2 Replies View RelatedLinksys Wireless Router :: RE1000 Wired PC Prompting User For Login Information For Wireles
Oct 30, 2012I recently installed an RE1000, which seemed to be working fine. Then, on 3 PC's with no wireless adapter installed we began being prompted for user name and password for the wireless router. Once I unplugged to extender the problem went away. I know what you're thinking: Maybe I just think there's no wireless adapter on these PC's. NO, I looked in device manager and the only network adapter installed is the ethernet adapter. These are all 4+ year old machines with no hardware changes made to them. Wireless adapters are not necessarily standard issue on old towers--even on new towers. The Acer I'm using right now was purchased new in November 2011 and did not come with a wireless adapter installed.
View 3 Replies View RelatedCisco Firewall :: RV180W / Multiple Hosts In DMZ In Small Business Router?
Aug 26, 2012I've got an RV180W for my office, and so far it has been great. I have two users that use a certain application that crashes all the time. For some reason, they don't crash when put into the DMZ. Is there any way i can put both of them in the DMZ? I can only figure out how to have one host in the DMZ at a time.
View 1 Replies View RelatedCisco Wireless :: Possible To Put Small Business Router RV120W Into Bridge Mode
Feb 10, 2012I want to know if it is possible to put the cisco small business router rv120w into bridge mode so that I can connect it to a linksys e2500 access point. Is this even possible or am I wasting my time?I have 4 devices connected to the cisco router that I want to be able to bridge to the linksys e2500 which has the internet connection.
View 1 Replies View RelatedUSG50 Best Gigabit WAN Router For Small Business VOIP Usage?
Mar 13, 2013I have a small business customer that is on the hunt for a new small business level router. While they are staying OK on a current consumer level gigabit WAN Netgear box, we are eager to implement something much better. After giving a Zyxel USG50 a try, we had a nightmare with their VOIP provider, Vocalocity, that doesn't like to have SIP ALG turned on (which Zyxel says is a requirement for their USG boxes to work with SIP service). I was curious if any of you had recommendations on great gigabit WAN small business routers (not UTMs of any sort).Here is their setup:
* 1 incoming WAN connection from a fiber provider called Sidera. They are achieving over 100Mbps currently and their provider Sidera REQUIRES us to have a gigabit WAN capable router in order to match the duplex and speed of their enteprise switches.
* About 8-12 office computers.
* About 8-10 VOIP desk phones through Vocalocity (Cisco SPA phones using SIP service, all cloud hosted - a Zyxel USG50 wreaked havoc on the service).
We are looking for something in the $100-250 price range. There seem to be a few options but I am not sure which one would be best to go with, that has a great compatibility out of box with cloud hosted voip phone service.
Any experience with any of the above units in such a setup as we have? The highest priorities for us are LAN-WAN throughput and VOIP quality/bandwidth/compatibility. Dual WAN is not a necessity, but nice to have. Prefer that all ports on the box are full gigabit if possible, but WAN has to be.
Cisco VPN :: PAK To Activate VPN On 1941 K9 Router
Jul 1, 2012We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies View RelatedCisco VPN :: Activating SSL On 1941 Router?
Mar 23, 2011I have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies View RelatedCisco WAN :: What Is The Processor Available In 1941 Router
Jan 31, 2012What is the processor available in cisco 1941 router? is it RISC?
View 4 Replies View RelatedCisco VPN :: How To Configure SSL VPN On 1941 Router
Mar 22, 2011How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View Related