cofigure a ADSL2+ Conexion in an 1941 router.line protocol are up but didn't have ip adresse in my interface.[code] i don't know how i can find the probleme, and debug's comandes no show me anything.
View 3 RepliesI'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View RelatedI've got some 1941 ciscos set on every branch.We have native L2 between this offices and I want to use external ip addresses on gig 0� interfaces anfdf local ip addresses on lo 0 interfaces, and use lo 0 for vpn connections.
I do:
int gig 0/0
ip add 192.168.181.14 255.255.255.0
ip nat outside
I can ping it from local network behind giga 0/1 but i can't ping it fro outside, how can i do this?
I have been trying to configure Cisco1941/K9 as Easy VPN Server through CiscoCP.The tunnel comes up but I cannot pass any traffic to the secure LAN (GigEth 0/1). When the tunnel comes up, I can ping the Loopback interface and the GigEth 0/1 interface IPs.
View 21 Replies View Relatedhow to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies View RelatedI had a Airtel connection with me for which i was provided Beetel 450 BXI ADSL2 + Router to connect to net using wi-fi on my laptop.How ever now i have changed my isp to ortel cable net providers.i access net on my laptop using lan cable connected from cable modem to my laptophow to configure Beetel 450 BXI ADSL2 + Router so that i connect my cable modem to Beetel 450 BXI ADSL2 + Router and access net wi-fi on my laptop. my os is vista.
View 1 Replies View RelatedI Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedI have some questions about how to configure my Cisco 1941 with a routed subnet from my ISP to forward them to 1 or more servers in my LAN.1 Routed subnet /29 from my ISP (over a fiber connection).In my LAN I have (at the moment) 3 servers, and about 15 clients.I would like to use the first ip address from the routed subnet for internet traffic from all the clients in the LAN.I would like to use the second ip address from the routed subnet for server1 so that server1 accept some allowed connections and that server1 connects to the internet with the second ip address from the routed subnet
I would like to use the thirth ip address from the routed subnet for server2 so that server2 accept some allowed connections and that server2 connects to the internet with the thirth ip address from the routed subnet.I would like to use the fourth ip address from the routed subnet for server3 so that server3 accept some allowed connections and that server3 connects to the internet with the fourth ip address from the routed subnet.[code]
I have Binatone DT 815 ADSL2 router (not wireless) with Airtel broadband connction. Recently it has started causing problem. About once in a fortnight, like � Additional log on information may be required� or �Your router is not registerd with us� or things like that. So every now and then the technician has to be called for configuring the router. After that it works for some days. Then again the problem and reconfiguring, which is quite problematic.
View 1 Replies View RelatedRegion : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
Is there any small router model (like 1941) that can be ready for future 4G LTE?
View 1 Replies View RelatedI have a 1941 Cisco router with WIC-!AM-V2 card that is uning pots( regural phone ) line for data traffic.the problem I am having is the line is establishing connection but it intermittently dropos.The router is configured to dial to Centraal office and I have more that 100 other locations with the same setup that are working fine. The only differene on htis one is it is going thru a PBX line.
View 1 Replies View Relatedi now learning about SSLVPN, and i already install license in 1941 with SSL and security9 License, i learning how to make a gateway for SSLVPN full tunnel, but i meet an obstacles, when i go to my wan ip address https://wan ip address, the browser give this
SSL connection error Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have.
Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error
[code]...
I currently have a Router that is ADSL2 & VPN capable. It currently allows me to work from home and connect to work servers securely. I have used traceroute [URL] in CMD to determine that all web requests/traffic goes through the VPN server rather than just the requests to access files on the VPN server.I don't feel comfortable having all my traffic now go through work servers(the VPN) so I would like to avoid this. I know I have 2 solutions:- Use Split Tunelling on the router where only requests to files on the VPN server will go through the VPN server, all other traffic is not through the VPN. I have heard that this can compromise the whole network as one node is currently 'unsecured' and can affect/compromise the whole network. Is this true?
- Add a second Router that doesn't connect through the VPN. When I finish work I disconnect from the VPN Routers wireless connection and connect through the second routers wireless connection. I would like to take solution 2 because I wont be compromising the whole network but I have some questions:- Is this something you would recommend?
- Is it dangerous? Is it just as compromising as solution 1?
- In Australia we use physical Phone Splitters for our internet physical connection. One side of the splitter connects to a phone line port on the wall. The other side has 2 ports, one for the phone line connection and one for the router/adsl connection. If I have 2 routers I'll need a splitter that has more than 2 ports so I can connect the 2nd router to the internet. Are there Phone Splitters with more than 2 ports and do ISP's allow me to do this?
I am doing a comparative between cisco and sonicwall routers. Which router would better fit me? i need it to support at least a 20MB internet connection in a datacenter and has to have a firewall included. I was thinking about a router 1941. What do you think ?
View 1 Replies View RelatedI am new to the Cisco routers but am trying to get a Cisco 887va working on a Eircom ADSL2 connection.
I was using the config of an old Cisco router as a guide, basically this has encapsulation aal5snap under the ATM interface, I am unable to set this in the 887va, I did read that this needs to be set under the VDSL controller however it will not take the commands. Also how can I set the the dsl operating-mode to auto.
Here is my config
Building configuration...
Current configuration : 1958 bytes!! Last configuration change at 13:20:03 UTC Tue Jul 17 2012version 15.1no service [code]...
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 1.0
ISP :
I recently bought this modem for use at home. When I try to log in to my computer at work I am able to log in to the server via a VPN connection but not onto individual computers via Remote Desktop Connection. Both computers run windows 7.
Region : UnitedStates
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.10 v0005.0 Build 120516 Rel.45877n
ISP : HiPointInc
Network Status.jpg
I've upgraded my line connection from 4mbps to 20mbps.I've also checked my status with HiPoint and on 192.168.1.1 which is shown on the attachment. No problems.
Max Downstream is 25612kbps but Current is only 4396kbps.Do I need to configure anything? Btw its directly connected to my PC?
When I start up my computer I cannot get an Internet connection. To get a connection I have to go into Control Panel, open Device Manager, click on Network adapters, which opens Realtek PCIe GBE Family Controller. I uninstall the Controller, restart and I then get an Internet connection. The Realtek controller then re-installs itself. I am using Windows 7 Home Premium operating system on my desktop. I am wired through a Dynalink RTA 1320 Rev 2 ADSL2+ Modem Router (provided and checked by my ISP). I have a Netgear Wireless N Router WNR 2000 for wireless connection to my laptop which has a Vista operating system. I have no connectivity problems to the laptop. I have had the connections checked by my ISP and the Netgear router by Netgear. They have both confirmed that there is connectivity to the desk top and the laptop and that the connections are working. Both have said that there is an issue with the operating system. I have got all the latest drivers installed and I get the message "Best driver software for your device is already installed".
View 10 Replies View RelatedRegion : Australia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0
Build 120926 Rel.27100n
ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies View RelatedRegion : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
Region : Ireland
Model : TD-W8980
Hardware Version : V1
Firmware Version : 0.6.0 0.6 v000 build 130303 rel. 38108n
ISP : Eircom
Bought this adsl router on Friday and since then I have been experiencing random frequent wireless dropouts, router appears to reboot at this point too, Internet drops out too. Wireless drops as I hear the beep from my airplay speaker reconnecting. Any one have these issues too, tired changing channels, then back to auto again, still no joy.
I have a Cisco 1801 that I am trying to set up for my DSL connection. I have configured the router but when I try to access a web site I receive the Http 404 page cannot be displayed error. I have checked my DNS server on the router & I believe that I have configured it correctly? I am hoping that one of you more experienced individual can take a look & tell me where I might have gone wrong. I have included the current running-configuration for your viewing pleasure.
View 4 Replies View RelatedI've just started styding for CCNA. Bought a router 871W recently and spent two days straight trying to configure internet connection with no luck! I use console port to do the configs and SDM/CCP. How to do simple internet connection configs. I googled everything but it's still confusing. I can't assing any IP to FA ports 0 - 3. I used VLAN instead. But all tutorials use FA0 and when I try to assign an IP to FA0 it gives me some L2 can't be assigned or something... :/ And I'm also confused what IP address should I use for WAN. I plugged the cable from Modem to PC's LAN port and wrote down some IP addresses which I think I'll have to use to configure the router for internet connection. And here they are:
ISP IP: 76.114.54.255
SUBNET: 255.255.248.0
GATEWAY: 76.114.48.1
DHCP: 69.252.97.4
DNS: 75.75.75.75
75.75.76.76
I have a problem to configure my connection SDSL.my router is SRP527W. my modem is Patton 3088. Do I need to update the ios? or there is a specific configuration of static IP ?
View 1 Replies View RelatedHow can I configure VPN connection between Cisco RV042 and Fritz!box 7170?I can establish VPN channel with Linksys RV042 with firmware 1.3.12.6-tm. When I set the same setting to Cisco RV042 (firmware v4.0.2.08-tm) VPN channel is not established.
View 1 Replies View Relatedwhat will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies View Relatedhow can i configure the SSL VPN users connexion to connecte from my remote PC (Windosws 7 32 & Internet Explorer
View 1 Replies View RelatedI've configured an srp541w router for a customer and successfully configured an IPSEC VPN connection with a Netopia router at a satellite office for the customer.
I cannot seem to find a way to configure either a PPTP VPN connection or QuickVPN connection for remote users. I did read something that stated that the router will only support either a site-to-site VPN or a QuickVPN connection, but not both at the same time.