I've configured an srp541w router for a customer and successfully configured an IPSEC VPN connection with a Netopia router at a satellite office for the customer.
I cannot seem to find a way to configure either a PPTP VPN connection or QuickVPN connection for remote users. I did read something that stated that the router will only support either a site-to-site VPN or a QuickVPN connection, but not both at the same time.
I'm running FW 1.2.4 and how to setup Remote Web Access over my IPSEC vpn tunnel. I would like to be able to remotely access these routers and make configuration changes from my main office but I cannot seem to figure out how to get it to work. If I try to access the internal router IP from across the VPN, I cannot. My VPN tunnel is up and operational and I can ping various devices across the tunnel but I cannot access the web management of the router.
I am trying to configure a SRP527W for a remote site.It needs to connect back to our Central Office, (via an ASA) which has several VLANs configured. I have entered the configuration for an IKE policy, and one for an IPSec policy (I can only enter one ip/subnet per IPSec policy)When I try to create a 2nd IPSec policy, if I point to the existing IKE policy, I get an error stating "IKE policy has been used by other IPSec policy".If I try to create a new IKE policy, using a different name, but with the same parameters, it shows an error stating the policy is a replica of an existing policy.If I create a new IKE policy, but use a different pre-shared key, then it is accepted by the 2nd IPSec policy, but that would mean I would have to create 2 seperate tunnels on the ASA, each using a different pre-shared key. I have never needed to do this for any of the other routers we have connected.
Recently we have purchased a few SRP541W for our small branch office VPN sites. While working with the config I have discoved that when trying to create a IPSec VPN policy, I am limited to only one "remote network" entry. This is typically not how VPN tunnels are bulit. We generally put the following remote networks in the tunnel. How do I open a BUG ticket with Cisco and ask that they change the code?
I'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
I have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?
We purchased a Cisco 541w router for one of our customers.
The main reason was to provide them with 3g backup solution for their business.
In order for the router to recognise the 3G router the firmware was upgraded SRP540_1.02.01_023_081211_1136.
We arrived on site last night to do the install but couldn't make any changes to the already configured router. Every time we attempted add a vlan or adjust the dhcp scope the router would return "The values are invalid".
Worked at this for over 1 hour and then decided to factory reset the router to see if that would revert the router to use the original firmware.
This didn't revert to the previous firmware but we magically could now make network changes without problem.
So everything was good, we reconfigured the router, tested 3G and failed the wan1 interface back and forth and the customer was very happy.
Customer arrived onsite this morning and the router was running on 3G. Every 8 - 10 minutes it was attempting a failover between connections.
I decided to turn off the failover for the time being and investigate further but yet again i was back to "the values are invalid"
We've had to pull the router as the customer is about 2hours away and revert back to their BT router.
Found this document for another SRP model - A warning message may appear in the Basic Wireless Settings screen with the text “The values are invalid” when modifying the wireless profile. Set the SRP 521W to its default setting (CSCtd49614).
[URL]
Will firmware SRP540_1.2.4_003_011112_1847 released only 2 days ago cure the problem?
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
I'm wondering if there is a possibility to get my homepage provider's custom dynamic DNS service working on my Cisco SRP541W Router as I'd not like to be forced to sign up for either DynDNS or TZO which are available through the web frontend.
I am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
We have an SRP541W on which I thought I had disabled DHCP, its turns out that in fact I haven't. After seaching again for the DHCP on/off funtion I found it under the Vlan settings (Wierd place to put it I thought).
The Router has a static ip address on the LAN side of 192.168.1.254 and is connected to a Cisco 2700 series on the WAN side. Our network DHCP is served by an SBS 2011 server hence my reason to switch off DHCP on the router. However when I select Static IP address from the Address Type in the VLAN settings and try and save the changes I get an error that is IP Address / Subnet Mask value is illegal. Great but why when the router has and IP address assigned and the subnet mask is set do I get this error. On the VLAN settings page there is no option to set an IP Address
Is there any way to setup an IPSEC tunnel to be able to go from my subnet, 192.168.75.x and be able to reach anything on the other side of the tunnel, 192.168.X.X?
Unfortunately, it does not appear as if the SRP500 series will allow you to create an ipsec policy where the local or remote traffic selection is 0.0.0.0/0.0.0.0. It wants a specific network. I have a scenario where I want to send all traffic over the vpn tunnel.
Is there a workaround to this or a special way to input "ANY" as the remote network?
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
I have a problem to configure my connection SDSL.my router is SRP527W. my modem is Patton 3088. Do I need to update the ios? or there is a specific configuration of static IP ?
I have a doubt. What I have to configure in my RV180 to make a VPN connection with Qvpn client. I created the user and if try to connect from the client I've recieved the message that is connected, but if I try to ping the RV180 local ip answer, but if I try to ping any other IP address of the VPN I can't. I think I would have something misconfigured but I don't know what is it.
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
On wireless (lenovo tabletx61) I cannot connect through the intranet - no problem connecting through internet. When I manage to connect through intranet connection is dropped quite often.No problem connecting via Ethernet cables.
I am trying to configure Remote Access VPN in our Cicco ASA 5520 firewall through SSL VPN wizard. I tried to configure Anyconnect VPN client option, but after entering user/pass it gives error "An error was received from the secure gateway in response to the VPN negotiation request. Please contact your network administrator. The following message was received from the remote VPN device: No assigned address"
As looking online there is no easy step-by-step option for same. I want to provide Remote Access VPN to some of our user abroad who should have access to few server applications and no internet access.
I am trying to configure remote access VPN to my network, i have a Cisco ASA 5510 IOS 7.0(7).
I configured the VPN using ASDM 5.0.9 and below is the configuration received:
access-list 90 extended permit ip 192.xxx.xxx.0 255.255.255.0 192.xxx.xxx.248 255.255.255.248 access-list ClientVPN_splitTunnelAcl standard permit 192.xxx.xxx.0 255.255.255.0 ip local pool VPNIpPool 192.xxx.xxx.250-192.xxx.xxx.252 mask 255.255.255.0[code].....
Not sure if my subject is a good decription of the problem or not.
I have an ASA 5520 at my home office and a SonicWALL NSA2400 at my remote office. The remote office has dual internet connections and I wanted to create two seperate VPNs between the devices using each internet connection on the SonicWALL.
I know how to configure this on the SonicWALL, the problem is on the ASA 5520
OK Basic network config
Main Office
ASA Public IP 1.1.1.1
ASA Internal network 192.168.1.0 (VPN source)
Remote office
Public IP 1 2.2.2.2
Public IP 2 3.3.3.3
Iternal network 192.168.2.0 (VPN destination on ASA)
If I have a VPN from the main ASA to either one of the SonicWALL's public IPs everything works fine
If I create 2 VPN tounels from the main ASA, 1 to each public IP on the SonicWALL, the VPN shows as up but no traffic flows.
I'm trying to configure a VPN remote access type on a SA520-k9 but i don't know why doesn't work.
My Internal network is 192.168.131.0/24 and my Wan Ip is 87.216.xxx.xxx.
on Remote WAN's IP Address / FQDN i put the WAN IP 87.216.xxx.xxx on Local WAN's IP Address / FQDN I put the cisco SA520 Ip. I think this is the problem.
I create a IPsec user. I create a firewall rule from WAN interface to SA520 Ip with IPSEC-UDP-ENCAP service.
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
