Cisco Routers :: SRP541W Multiple WAN Configuration
Apr 3, 2013
I have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?
View 5 Replies
ADVERTISEMENT
Jan 4, 2013
I have setup 15 x RV180W's so far for a particular client.They have requested that we add a Corporate Wireless VLAN for their laptop users (not guests) and add a Special Use WiFi VLAN for a particular mobile platform that is being deployed (in this case we need 2 separate WiFi VLANs to ensure compliance).Also, none of the VLANs can talk to eachother and they have their own subnets.I have the Wireless and VLANs setup, no problem... but I am having an issue wiht the VPN settings.I have the wired network's subnet working fine. But I do not know how to add the subnets for both Wireless VLANs to the traffic selection.The IP schemes will not allow me to just select a large subnet... here are some examples:
Wired VLAN: 10.10.x.y
Corporate WiFi VLAN: 10.15.x.y
Special WiFi VLAN: 10.18.x.y
x is the octet that defines the physical unit location (unit 1 = .23, unit 2 = .24, etc...) y is the octet the host.Since they are not in a contiguous block, I cannot just use a larger subnet mask.I can add multiple traffic selection rules to the ASA5515 at HQ, so that side of the tunnel is perfect... I just don't know how to add the three VLANs to the RV180. Is it as simple as using commas or semicolons?
View 1 Replies
View Related
Jun 2, 2011
i have gotten a question from a partner in regards to the throughput on both LAN and WAN on the SRP541W. I can't really find that on the datasheet.
View 4 Replies
View Related
Mar 17, 2013
I just bought the SRP541, and it has the old firmware. I downloaded the new firmware, yet I cannot figure out how to install it.
View 3 Replies
View Related
May 15, 2013
Recently we have purchased a few SRP541W for our small branch office VPN sites. While working with the config I have discoved that when trying to create a IPSec VPN policy, I am limited to only one "remote network" entry. This is typically not how VPN tunnels are bulit. We generally put the following remote networks in the tunnel. How do I open a BUG ticket with Cisco and ask that they change the code?
View 3 Replies
View Related
May 9, 2013
I am curious of the max supported SIP sessionf of the SRP500 series.
View 1 Replies
View Related
May 9, 2012
I'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
View 2 Replies
View Related
Feb 2, 2012
We purchased a Cisco 541w router for one of our customers.
The main reason was to provide them with 3g backup solution for their business.
In order for the router to recognise the 3G router the firmware was upgraded SRP540_1.02.01_023_081211_1136.
We arrived on site last night to do the install but couldn't make any changes to the already configured router. Every time we attempted add a vlan or adjust the dhcp scope the router would return "The values are invalid".
Worked at this for over 1 hour and then decided to factory reset the router to see if that would revert the router to use the original firmware.
This didn't revert to the previous firmware but we magically could now make network changes without problem.
So everything was good, we reconfigured the router, tested 3G and failed the wan1 interface back and forth and the customer was very happy.
Customer arrived onsite this morning and the router was running on 3G. Every 8 - 10 minutes it was attempting a failover between connections.
I decided to turn off the failover for the time being and investigate further but yet again i was back to "the values are invalid"
We've had to pull the router as the customer is about 2hours away and revert back to their BT router.
Found this document for another SRP model - A warning message may appear in the Basic Wireless Settings screen with the text “The values are invalid” when modifying the wireless profile. Set the SRP 521W to its default setting (CSCtd49614).
[URL]
Will firmware SRP540_1.2.4_003_011112_1847 released only 2 days ago cure the problem?
View 1 Replies
View Related
Mar 20, 2013
the small fan of a SRP541w seems to have 'melted' it's way out of it's casing. How to know part number for a replacement fan for this router?
View 3 Replies
View Related
May 9, 2012
I'm running FW 1.2.4 and how to setup Remote Web Access over my IPSEC vpn tunnel. I would like to be able to remotely access these routers and make configuration changes from my main office but I cannot seem to figure out how to get it to work. If I try to access the internal router IP from across the VPN, I cannot. My VPN tunnel is up and operational and I can ping various devices across the tunnel but I cannot access the web management of the router.
View 4 Replies
View Related
Mar 25, 2013
I'm wondering if there is a possibility to get my homepage provider's custom dynamic DNS service working on my Cisco SRP541W Router as I'd not like to be forced to sign up for either DynDNS or TZO which are available through the web frontend.
View 1 Replies
View Related
Jun 20, 2012
I've configured an srp541w router for a customer and successfully configured an IPSEC VPN connection with a Netopia router at a satellite office for the customer.
I cannot seem to find a way to configure either a PPTP VPN connection or QuickVPN connection for remote users. I did read something that stated that the router will only support either a site-to-site VPN or a QuickVPN connection, but not both at the same time.
View 2 Replies
View Related
Nov 19, 2012
I am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
The rest of router setting are default.
View 17 Replies
View Related
Apr 24, 2013
We have an SRP541W on which I thought I had disabled DHCP, its turns out that in fact I haven't. After seaching again for the DHCP on/off funtion I found it under the Vlan settings (Wierd place to put it I thought).
The Router has a static ip address on the LAN side of 192.168.1.254 and is connected to a Cisco 2700 series on the WAN side. Our network DHCP is served by an SBS 2011 server hence my reason to switch off DHCP on the router. However when I select Static IP address from the Address Type in the VLAN settings and try and save the changes I get an error that is IP Address / Subnet Mask value is illegal. Great but why when the router has and IP address assigned and the subnet mask is set do I get this error. On the VLAN settings page there is no option to set an IP Address
View 4 Replies
View Related
Jun 12, 2012
Is there any way to setup an IPSEC tunnel to be able to go from my subnet, 192.168.75.x and be able to reach anything on the other side of the tunnel, 192.168.X.X?
View 5 Replies
View Related
Feb 26, 2012
Unfortunately, it does not appear as if the SRP500 series will allow you to create an ipsec policy where the local or remote traffic selection is 0.0.0.0/0.0.0.0. It wants a specific network. I have a scenario where I want to send all traffic over the vpn tunnel.
Is there a workaround to this or a special way to input "ANY" as the remote network?
View 3 Replies
View Related
Sep 21, 2011
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
View 3 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Apr 13, 2013
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies
View Related
Oct 13, 2011
I have faced configuration of multiple nat/pat problem.Point is when I paste into router another nat pool or nat with route-map or just static nat they doesn't work I mean only one of them works.So, I have several connection hardware cisco 2811 latest ios 15.1
1. internet
2. Local host that must be translated into global local ip addresses be routed
3. vpn local hosts that must be translated into local global addres
View 4 Replies
View Related
Sep 11, 2011
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies
View Related
Aug 19, 2012
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
View 14 Replies
View Related
Oct 4, 2012
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
View 4 Replies
View Related
Mar 20, 2012
I've got a question concerning the configuration of multiple AP manager interfaces on -for example- a cisco WLC 2504. I've read the configuration guide but I'm not sure whether this is the way the protocol works. Say I want to distribute AP's (and traffic) across various AP Manager interfaces on the WLC. I would configure the following:
Create one management interface (which will automatically also be an AP-Manager interface)Configure 1 (or more) Seperate ap-manager interfaces, assign them to a port number, and select "Enable dynamic AP Management". VLAN ID's will be the same.Create a WLAN and configure it's interface to "management" Is it correct if I state that the LWAPP protocol takes care of the discovery from the Access Point and sends information about the available AP-manager interfaces back to the AP and the AP knows which ap-manager interfaces are available, connecting to the least loaded one?
View 3 Replies
View Related
May 1, 2013
is there a way on a WLC5508 to push the same configuration on multiple APs in 1 shot?I need to change the High Availability settings on most of the APs (not all). And the only solution i find is to do 1 by 1...
View 6 Replies
View Related
Mar 11, 2013
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies
View Related
Dec 5, 2011
I know this is not a the preferred way to do it, but this just an interim network configuration until the Remote Site gets re-located and reconfigured. I'm trying to bridge and route traffic and hoping the community can offer a review of the sample configuration and/or some ideas to make this a reality.
Existing network is bridged across site-to-site private line (p-2-p) so 192.168.100.0/24 devices exist at both locations. In order to reduce bandwidth consumption across the p-2-p, the 172.20.100.0/24 devices (end user PCs and new to the environemnt) will be routed out a local Internet connection which in turn reduces the p-2-p traffic to just private network traffic for the two networks. That same network requires routing through the 192.168.100.0/24 network in order to access the private WAN connected to the 3900 router with IP 192.168.100.1.
View 0 Replies
View Related
Jul 19, 2012
I am trying to build a site-to-site VPN between cisco 1811W at a main office and SRP541W at a remote office.
I already have the configuration for the 1811W through SMD, but can't install the SDM on the SRP541W.
Does the SRP541 is compatible with SDM; and if not is there any other GUI to configure a VPN tunnel on SRP541.
View 1 Replies
View Related
Apr 15, 2012
We have 2 servers currently and are adding one next month. All need to be accessible using a different web address. We have setup a records for the 2 existing servers but cannot get NAT to work properly. We have a block of 5 IP's from FIOS. x.x.x.146-150 and have tried using 146 and 150 as the main WAN static IP with no success in getting the other address to communicate to the corresponding server.
What we need...
Server @ address 192.168.2.2 - SBS Server, standard SBS ports - currently working via port forwarding with WAN static of .150
Server @ address 192.168.2.3 - RDP, HTTP, HTTPS, and others. Some ports are the same as SBS. Trying to NAT .149 to this server.
Server @ address 192.168.2.4 - RDP, HTTP, HTTPS, and others. Some ports are the same as SBS. Trying to NAT .148 to this server.
All servers are on VLAN 1 which has a static IP of 192.168.2.1. DHCP is controlled by SBS.
View 2 Replies
View Related
Dec 7, 2011
i have recently successfully configured an IPSEC VPN from a SRP541 to our Zyxel Zywall 70 (main site).
I can ping all devices on the remote Site except the Cisco-Router!I tried to disable tohefirewall and did set "Anonymous Internet Requests" to "disabled".But still no ping (and no web management) over the VPN possible.
I must admit i am totally new to Cisco devices (up to now, we used only Zyxel) - so is guess it must be something very basic i am missing.
View 1 Replies
View Related
Oct 24, 2011
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
View 4 Replies
View Related
Oct 22, 2012
I used to have a DLINK router which covered my whole house with its Wifi signal. After upgrading to the SRP541W router, only the very close vicinity of the router has any acceptable level of signal to use devices. I seriously need to improve WIFI range to accomodate my small business. I asked the Live chat technician and the answer was "This device does not support external antennae" and then silence. Okay it is not supported but what I am looking for is a solution, not a dead end.
For example, is there a cisco repeater/extender that I could deploy that works with the SRP541W router? Any experience adding one long cable and putting one antenna at a different location of the house?
View 3 Replies
View Related
Apr 15, 2013
I am new to VLANs although I generally understand the concept. I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access. My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports. I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains. Also, do I need a management VLAN??
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??
View 4 Replies
View Related
