Cisco Wireless :: C1131AG - Multiple SSID With Multiple VLANs Configuration On Aironet AP
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
ADVERTISEMENT
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Nov 18, 2012
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies
View Related
Oct 12, 2011
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
View 2 Replies
View Related
Dec 22, 2009
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
View 2 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Apr 3, 2012
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Aug 19, 2012
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
View 14 Replies
View Related
Sep 8, 2009
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies
View Related
Apr 29, 2003
On a 1200AP, I have set up multiple SSID's. Generally, broadcast is set on. Why can I only see the default SSID and not the others?
View 3 Replies
View Related
Jun 2, 2010
We just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
View 40 Replies
View Related
Jan 31, 2012
We have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies
View Related
Aug 11, 2011
I have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.
Should I be adding the additional MACs there?Does the WAP200 even support multiple VLAN/SSID?
Network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
View 2 Replies
View Related
Sep 26, 2011
I have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
View 1 Replies
View Related
Sep 26, 2012
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
View 3 Replies
View Related
Aug 2, 2012
I have a Cisco AIR-AP1242AG-A-K9 Autonomous AP running firmware 12.4(25d)JA. I wish to set up multiple SSID's (2) each having their own separate security types. Both security types may end up being WPA2, but would have separate keys. I do not have a managed switch, the AP is connected to a "dumb" switch in an office environment, with no VLANS. Also this is only for 1 access point.
I have tried creating 2 SSID's, but my issue is that only one SSID will actually work at a time, meaning that only the native VLAN in the AP will actually allow wired traffic through it's SSID. How can I set up 2 different SSID's, with 2 independant security types and have them work simultaneously? Is this functionality supported by this AP?I feel that this is possible, as I can easily set this up on other access points from other manufacturers.
View 4 Replies
View Related
Feb 20, 2008
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies
View Related
Apr 7, 2013
I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
View 5 Replies
View Related
Feb 3, 2013
I currently have an 867vae router and a 1131ag ap setup with 2 vlans and 2 ssid's. I am in the process of baby proofing the house and would like to use the cisco plsk400 homeplug system to relocate my wap. I use 2 networks to seperate and filter the kids internet traffic from my own. It also allows me to shut the kids vlan when they shouldnt be on the internet.
As far as i can tell the plsk400 homeplug doesnt support 802.1q.... so is there any way i can keep the seperate networks/SSID's and the abilty to filter and turn off one of them at will without a trunked link to the router?
View 2 Replies
View Related
Feb 17, 2013
i' ve got 2 cisco 1130 AG AP's , i want both of them to broadcast 2 ssid's per AP, i've done so far but my clients cannot get a ip adress from the dhcp server.
View 19 Replies
View Related
Mar 16, 2013
I have a wlc2112-k9. I have succesfully setup a WLAN with 802.1x authentication and dynamic VLAN assignment. The issue I have (and maybe it isn't an issue and just the way the controller works) is that if the vlan interfaces I have defined are connected to different ports from which the default interface for the WLAN it doesn't work.So for instance, I create my WLAN and set the interface to the management interface (which is connected to port 1). I then define all my other vlan interfaces that could be returned by my radius server.[code]
Port 1 is configured on the switch on vlan 21. If the radius server returns a VLAN ID of 102, 104 or 106 my client successfully connects to the WLAN but it gets put on VLAN 21. However if I move the vlan interfaces above over to port 1 the client correctly gets put on the correct VLAN.All ports on the switch are configured as trunk with the native vlan set to the corresponding value that is set on the WLC.
Is this just the way the controller functions? That it can't assign a client to a different interface that is connected to a different port from the default one setup when the WLAN is created? I would have just though that if the radius server returned VLAN 102 that it would find that interface and connect the user session via that interface regardless of the port it is configured on.
View 11 Replies
View Related
Apr 24, 2013
We have a pair of 1310's (running 12.3(8)JEA3) connecting 2 buildings together. The wired side of each AP is connected to switchports configured as access ports.
But, now we need to extend multiple VLANs across the wireless bridge. So I'm thinking I just need to configure some sub-interfaces on the radio side and ethernet side and bridge them together. But I'm unclear on if I need an SSID for each bridge group. I would hope not. But after reading this, I'm not sure. Most of the documentation seems to be dealing with wireless clients. Well, in this case I don't have any wireless clients and just need to extend VLANs.
These 2 sites are hundreds of miles away from where I am, and I don't have any 1310's to test this out on. Should I be able to load similar software on other AP's (like 1142's) and have them function as bridges to test this out?
View 3 Replies
View Related
Feb 27, 2013
I read from this forum some discussion about the WLC VLAN Select feature. [URL]. I see that you can use this feature to have multiple VLANS (interfaces) to map to the same WLAN (SSID).
What I try to learn is under what scenarios would people need to have mutliple vlan mapped to single SSID?
In my environment, I have 50+ AP int he campus on 20+ Cisco 4500 switches. I have single WLAN and it is mapped to one subnet. All wireless users would be on that subnets, whereas wired users are on 20+ subnets of their own.
View 6 Replies
View Related
Aug 15, 2012
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies
View Related
Aug 15, 2011
So My ssid is naular and it has password protection. However there is another ssid from my router called "linksys" which is unprotected. I tried to change it and messed it up bad. Everyime I sign on to "naular" it makes "Naular 2" then Naular 2 3 then Naular 2 3 4 etc. Then I only get local access. I look at my wireless thing and it says i'm connected to naular 2 3 4 5 when I signed onto Naular earlier.
View 1 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Jan 10, 2012
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies
View Related
Apr 23, 2012
I'm trying to figure out if it is possible to configure in one site a wireless setup that goes like this:
One WLC (5508), multiple LAP's in H-REAP mode.
AP's will be splitted in multiple VLAN's belonging to different departments but with the same SSID.Each VLAN will have it's own DHCP scope. All AP's are located in the same site and I need to know if it is possible to roam between AP's that belong to different departments?
View 3 Replies
View Related
Jan 17, 2013
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies
View Related
May 13, 2013
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
View 3 Replies
View Related
Jan 26, 2013
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies
View Related
