So My ssid is naular and it has password protection. However there is another ssid from my router called "linksys" which is unprotected. I tried to change it and messed it up bad. Everyime I sign on to "naular" it makes "Naular 2" then Naular 2 3 then Naular 2 3 4 etc. Then I only get local access. I look at my wireless thing and it says i'm connected to naular 2 3 4 5 when I signed onto Naular earlier.
View 1 RepliesI just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies View RelatedIs it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I have a wrt610n that I've used for years with no problem. The usb drive I've had plugged into it has worked great for a really long time, but it's fairly small. I bought a WD 1TB hard drive, formatted it with the router set everything up. after about a day I tried to upload a file from work and got an error, and it wiped the harddrive clean. I reloaded thinking it was a fluke and everything worked fine for about a month. Uploading and downloading worked fine from where ever I was at, on the local network or over the internet. Then I tried to upload a small file, got the error and all of my files were gone again.
View 1 Replies View RelatedI tried to block youtube and facebook https in my router WRT610 V1 but the router fails blocking these websites. But, it does work for blocking youtube and facebook http.
View 9 Replies View RelatedI had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n. I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch. I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message.
View 7 Replies View RelatedI have a WRT610 and am unable to connect any devices wirelessly. All the lights on the right hand side of the router are on except for the USB connection....what am I doing wrong? The router has worked for about a year flawlessly and last night all wireless connections quit.
View 9 Replies View Relatedhow i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View Relatedi have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies View Relatedi bought a WRT160N router
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
E4200 not letting my known wireless devices connect when SSID Broadcast is turned off.
View 1 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.Should I be adding the additional MACs there?
Simple network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
I'm using a Linksys E1500 on my Timewarner 20Mbs connection and I've noticed that anytime another computer on my network connects my connection speed take a significant drop. This happens when Macs or PCs connect and there doesn't seem to be any common ground between any of them. In addition the connection is slow wether the other PCs are idle or downloading anything, it seems to make no difference. my ping in any game drops from 70 to 500 just for 2 other PC being on at the saem time on the network.
View 2 Replies View Relatedi`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
As of last night my router has been producing slow connectivity when multiple users are connected to it, but it's perfectly fine when only one user is connected. I am on a laptop myself, but we also have a second laptop and a desktop where the modem and router are set up. I have upgraded the firmware so that is up to date. We have Comcast Fiber Optics so my internet speed is normally quite fast even when all of my computers are connected.
I am using DHCP Configuration. My Channel Width is set to 20 MHz and I am using Channel 11. The Security Mode is set to WPA Personal. I had it on WPA2 Personal but I read that changing to WPA Personal might work and so far it doesn't seem to have done anything. I set the Beacon Interval to 50, Fragmentation Threshold to 2304, and RTS Threshold to 2304. Everything else is set to the default factory configuration.
Just today I received a notice that said "Windows has detected an IP Address Conflict", but ever since I reinstalled the Firmware it hasn't come back. I've rebooted both my laptop and the desktop to confirm it hasn't come back as well. I've tried everything that I could think of including reconfiguring my router and restarting my modem as well.
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies View RelatedOn a 1200AP, I have set up multiple SSID's. Generally, broadcast is set on. Why can I only see the default SSID and not the others?
View 3 Replies View RelatedWe just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
We have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.
Should I be adding the additional MACs there?Does the WAP200 even support multiple VLAN/SSID?
Network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies View RelatedI have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
I have a Cisco AIR-AP1242AG-A-K9 Autonomous AP running firmware 12.4(25d)JA. I wish to set up multiple SSID's (2) each having their own separate security types. Both security types may end up being WPA2, but would have separate keys. I do not have a managed switch, the AP is connected to a "dumb" switch in an office environment, with no VLANS. Also this is only for 1 access point.
I have tried creating 2 SSID's, but my issue is that only one SSID will actually work at a time, meaning that only the native VLAN in the AP will actually allow wired traffic through it's SSID. How can I set up 2 different SSID's, with 2 independant security types and have them work simultaneously? Is this functionality supported by this AP?I feel that this is possible, as I can easily set this up on other access points from other manufacturers.
I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
I currently have an 867vae router and a 1131ag ap setup with 2 vlans and 2 ssid's. I am in the process of baby proofing the house and would like to use the cisco plsk400 homeplug system to relocate my wap. I use 2 networks to seperate and filter the kids internet traffic from my own. It also allows me to shut the kids vlan when they shouldnt be on the internet.
As far as i can tell the plsk400 homeplug doesnt support 802.1q.... so is there any way i can keep the seperate networks/SSID's and the abilty to filter and turn off one of them at will without a trunked link to the router?
i' ve got 2 cisco 1130 AG AP's , i want both of them to broadcast 2 ssid's per AP, i've done so far but my clients cannot get a ip adress from the dhcp server.
View 19 Replies View RelatedI have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedHouse has 2 floors. I want to install 2 E3200, one on each floor, but both with the same SSID/Password, etc. so internet connection/streaming throughout the floor is seamless.
Both floors have network wall sockets ready and they all lead to the same modem/router so all devices plugged lead to the same network.
PS. both E3200 have been update to Firmware Version: 1.0.03