Cisco Wireless :: 867vae - Multiple SSID And Networks Without 802.1q Trunk
Feb 3, 2013
I currently have an 867vae router and a 1131ag ap setup with 2 vlans and 2 ssid's. I am in the process of baby proofing the house and would like to use the cisco plsk400 homeplug system to relocate my wap. I use 2 networks to seperate and filter the kids internet traffic from my own. It also allows me to shut the kids vlan when they shouldnt be on the internet.
As far as i can tell the plsk400 homeplug doesnt support 802.1q.... so is there any way i can keep the seperate networks/SSID's and the abilty to filter and turn off one of them at will without a trunked link to the router?
View 2 Replies
ADVERTISEMENT
Aug 11, 2011
I have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.
Should I be adding the additional MACs there?Does the WAP200 even support multiple VLAN/SSID?
Network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
View 2 Replies
View Related
Aug 10, 2011
I have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.Should I be adding the additional MACs there?
Simple network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
View 1 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
Sep 8, 2009
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies
View Related
Apr 29, 2003
On a 1200AP, I have set up multiple SSID's. Generally, broadcast is set on. Why can I only see the default SSID and not the others?
View 3 Replies
View Related
Jun 2, 2010
We just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
View 40 Replies
View Related
Jan 31, 2012
We have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies
View Related
Nov 18, 2012
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies
View Related
Sep 26, 2011
I have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
View 1 Replies
View Related
Sep 26, 2012
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
View 3 Replies
View Related
Aug 2, 2012
I have a Cisco AIR-AP1242AG-A-K9 Autonomous AP running firmware 12.4(25d)JA. I wish to set up multiple SSID's (2) each having their own separate security types. Both security types may end up being WPA2, but would have separate keys. I do not have a managed switch, the AP is connected to a "dumb" switch in an office environment, with no VLANS. Also this is only for 1 access point.
I have tried creating 2 SSID's, but my issue is that only one SSID will actually work at a time, meaning that only the native VLAN in the AP will actually allow wired traffic through it's SSID. How can I set up 2 different SSID's, with 2 independant security types and have them work simultaneously? Is this functionality supported by this AP?I feel that this is possible, as I can easily set this up on other access points from other manufacturers.
View 4 Replies
View Related
Apr 7, 2013
I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
View 5 Replies
View Related
Feb 17, 2013
i' ve got 2 cisco 1130 AG AP's , i want both of them to broadcast 2 ssid's per AP, i've done so far but my clients cannot get a ip adress from the dhcp server.
View 19 Replies
View Related
Oct 12, 2011
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
View 2 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Dec 22, 2009
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
View 2 Replies
View Related
Aug 15, 2012
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies
View Related
Aug 15, 2011
So My ssid is naular and it has password protection. However there is another ssid from my router called "linksys" which is unprotected. I tried to change it and messed it up bad. Everyime I sign on to "naular" it makes "Naular 2" then Naular 2 3 then Naular 2 3 4 etc. Then I only get local access. I look at my wireless thing and it says i'm connected to naular 2 3 4 5 when I signed onto Naular earlier.
View 1 Replies
View Related
Apr 3, 2012
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies
View Related
Sep 21, 2012
We have 7 3560's in 7 different locations connected to our providor for wan access. Our provider has given us a copper cable at each point and we have connected it directly to our 3560 switch at each location. Each port is configured the same way at each location. Each switch is running eigrp.All of the switch ports on each switch are configured as a trunk and vlan 299 had the ip address for the eigrp connection: [code] This setup is working as each switch see's all of the other switches as an eigrp neighbor. We have also made sure that the switch at our head office has spanning tree priority for vlan 299.
So the problem is, if there is a change in the topology at one of the locations it usually causes one or more of the other connections to go down for some reason. We just cannot pinpoint what is causing this change. There are no log's or anything other than an eigrp hold time expired message.?
View 9 Replies
View Related
Feb 11, 2011
setting up networks with multiple locations and multiple wireless points.For example: My sisters' home has here modem in her main computer room, it has a Belkin router hooked to the modem. Then a line goes from there to my nephew's room where I tried to expand their network by adding another router. I really just wanted an access point, but they don't seem to sell these as much as they used to. Anyway, I had it working, but it was two different networks, NETWORK1 and NETWORK2. So they had to swap networks when moving around the house. what would be the best hardware setup to provide both sides of the house with some Hardwired access as well as wifi access? Right now, we have two routers, a DIR615 (or something like that) and a Cisco E1000, and again hardwire going from the main computer room to my nephew's room.Also, in my house, I have lots of stuff... I have an Actiontec Router from FIOS, feeding a small hub as well as a switch in my main room. Which then feeds a Ps3, Wii, laptop, Denon reciever, and Access Point... and also feeds my Apple TimeCapsule, which also feeds my printer. My wireless devices range from cameras, iphones/ipads, and a wifi unit (I forget what it's called, but it connects my DVR wirelessly to my network, and the DVR itself doesn't have wifi).
my question about my setup is, should everything be on one network... as in let the ActionTec handle most of the duties and use switchers and accesspoints to extend the network. Should everything be on the same wireless network and channels? Like if I used my access point to extend, do I want the same settings as my main wireless router, and would that be the same for the Apple Airport Extreme?Also, does having all these wireless networks going create any kind of hinderance on my performance. For example, the PS3 has some sort of wifi in it... it produces a SSID, but I never connect to it. Should I make sure that's off? And in my main room, should I go with just the AirPort extreme over using it and the Wireless Access point.
View 1 Replies
View Related
Sep 12, 2012
We are using cisco 3502i AP's and 5508 controler. We have two SSID's. "SA Wireless" and "Guest Wireless". SA Wireless is WPA2 enterprise security and the "Guest Wireless" is open. The iPads will disconnect from "SA Wireless" and join "Guest Wireless" at random. Is there a way to force them to stay on "SA Wireless" and only change if you actually tell the iPad to change?
View 1 Replies
View Related
Sep 25, 2012
when I try to enable a WLAN that is using the same SSID as another WLAN I get this message
The following errors occurred while updating the WLAN:
WLAN with duplicate SSID and L2 security policy found.
each location has its own interface because each site is setup on our 6509 with a different VLAN. What is the best way to work around this.
View 10 Replies
View Related
Feb 14, 2012
I am having trouble setting up two networks.Basically, i want one 'private' network and one public network. The problem is, the private network can't access the internet.(Network 2)
Network 1(Public) works fine as i don't want them to access Network 2.Here's how it is setup.
Internet
|
Router/Modem (Network 1)
|
Server NIC1
Server NIC2
|
Switch - (Network 2)
Network 1 can access the internet and shared files on the server.
Network 2 can access Shared files on the server (which is what i want) but cannot access the internet.
Router/modem IP is 10.10.1.254 subnet 255.255.255.0
Server NIC 1 IP is 10.10.1.252 subnet 255.255.255.0
Server NIC 2 IP is 10.10.1.251 subnet 255.255.255.0
How can i get computers in Network 2 to access internet?
View 5 Replies
View Related
Aug 30, 2011
Explain the risks of not using multiple networks on a 300 host LAN
View 1 Replies
View Related
May 12, 2011
I manage a network using Windows Server 2008 r2 that connects to the Internet (ISP) through a wireless radio antenna. We have three other locations that also connect to the same ISP through wireless radio antennas on the roof of each building. Those locations are windows XP machines. Each location is separated by more than 1,000 ft and do not have line of sight to each other. I'm wanting the XP machines to be able to logon to the domain of the server and access shared files
View 1 Replies
View Related
Nov 1, 2011
Everytime I disable SSID Broadcasting 2 extra wireless connections appear available connections list. (See wirelessconnections.jpg) One is blank and one is labeled Other Network. They disappear when I enable SSID Broadcasting. I am not sure why this is happening.
View 5 Replies
View Related
Sep 20, 2011
I currently have a hub-and-spoke VPN configuration with 6 ASA 5505's at remote sites all connected to an ASA 5510 at HQ via IPSEC lan-to-lan tunnels. My current configuration allows hosts on the remote site networks to talk to hosts on the HQ network, but not to hosts on the other remote sites.I have receieved a request to allow comminucation between the remote sites as well, with traffic all routed through the 5510 at HQ.
View 1 Replies
View Related
