Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 RepliesMy question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedI can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
I am trying to come up with a wireless solution for a campus deployment. The campus has ten buildings currently using Autonomous APs and are currently converting to Dual 5508 Controller model.
I would like to have a separate AP Mgmt subnet in each building, so I will configure an ip helper on the SVI on this vlan to:
Option1 - Point to the Internet Router configured with DHCP Option 43 with the controller IP addresses
Option 2 - Point to the Wireless LAN Controller itself.
Problem with Option 1 is that the Internet Router will now have to connect directly to the COE network to be able to route back to the AP mgmt subnets. So I would emply a VRF here to keep the separation.
Problem with option 2 is that there appears to only be one DHCP scope allowed on the controller. So this would mean a flat mgmt network across all buildings which I am trying to avoid. I know that after the AP joins the controller, I could change the IP and change the vlan on the port but this is not very neat.
So question is:
Is there a way of getting multiple DHCP pools on the controller?
My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies View RelatedI recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies View RelatedSwitch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies View RelatedI have a above said switch at my remote office (600KM) which is connected with L2 Point to Point leased line. Both the ends I have Cisco 3950 catalyst switches with Vlans configured at both the ends. Now, for obvious reasons I should remove the other end 3950 switch and replace with Cisco 2950 switch. The other end 3950 is having 4 Vlans configured on 4 ports. Now my requirement is, I should configure 3 Vlans (one for P2P, one for 10 Desktops and one for to bring traffic from other network).
View 1 Replies View RelatedI have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
I was assigned a task to configure an SG300-28P to have 3 different vlans.Now on VLAN1 their will be only one device configured with static IP 192.168.0.230,On the other 2 VLANS there will be a separate router connected on each one of them and will also act as a DHCP server.
View 4 Replies View RelatedI am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
We have been set the task of securing a small managed office system which is currently set up with a standard switch allowing each of the offices (containing different companies) to see each other, and in some cases, access each others documents across the network.
Obviously this is a far from adequate set up and our aim is to isolate each office using VLAN's but share a common internet connection provided by the managed offices. We have two Cisco SGE2000-G5 layer 3 switches but we are new to Cisco equipment and VLAN's so we are not quite sure on how to implement this. DHCP would need to be provided by a Router, there is no Server. We are open to suggestions on the Router as we have yet to purchase one.
I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies View RelatedWe need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies View RelatedI recently changed the entire configuration on two 6509 switches, and the fibre modules on slot 7 and 8 have gone down on BOTH switches. It would be easy to say that its a hardware fault but I cannot understand how module 7 and 8 can go down on both switches. Initially I thought it maybe due to IOS bug 22-33.SXI2a.bin" so I upgraded it to s72033-advipservicesk9_wan-mz.122-18.SXF12a.bin but it still down.These are the actions I have carrried out to try resolve the issue:
- Reverted back to orginal configs but no luck
- Tried to use "power enable" command but the status light on both modules seems to turn red and then go off again.
- I have also tried to put one of the fibre modules into a different slot but no joy
- Upgraded the IOS from 22-33.SXI2a. to 122-18.SXF12a
I am sure that hardware fault cannot occur on BOTH modules 7 & 8 on BOTH switches after config change.The error in the log shows that modules "failed to bring online because of registration timer event". I understand this means that it is unable to download the image within the allocated time. [code]
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
can i have on asa 5510 multiple pools and multiple group authentication for various departments along with restricted access if any
View 3 Replies View Relatedi have 6509+FWSM(4.0.4) now i wanna use stite to stite and ez vpn in the fwsm (multiple context) multiple context mode in fwsm support ipsec vpn?
View 2 Replies View RelatedWe have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can I restrict access to the server VLANs?Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered ?
View 9 Replies View RelatedWe have a HP Procurve 5412zl switch as our default gateway for all our VLANs from there the traffic will be going to a Cisco ASA 5515 and then to a Cisco 3800 Router then to our ISP.
We have yet to purchase the ASA but my question is about my future configuration. I will have the router of last resort on the 5412zl setup to point to the ASA inside interface, how does that work with multiple VLANs? For instance the ASA inside interface would be 10.0.0.1 but traffic could come from another VLAN via the switch with a 192.168.1.x address. Would the ASA just pass it on to the router? Or would it conside this spoofing and drop the packet?
Lastely, if we have WCCP set for the ASA's inside interface, how would it handle the redirect for multiple VLANs ip addresses? Would I use GRE for the redirect to my web filter?
I can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies View RelatedI want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
I have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View Related3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
I would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0
[Code].....
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.
I am a fairly basic configs that I just can’t figure out what I am doing wrong. I have what I would consider a fairly basic config that I just can’t seem to get to work and I am sure it is something I am just not doing or grasping. Basically I have two 3560 switches that I would like to connect together with four 1Gb ports and trunk four vlans across said port-channel, I created the port-channel and set it to switchport trunk encapsulation dot1q I then set all four ports to channel-group # mode on. With that setup I can’t ping from switch to switch on the nonnative vlan.
View 6 Replies View RelatedThe field engineer has a stand alone 24 port 2900 series switch that he has different equipment connected to and are segmented using VLANs. So for example, he's got ports 1-4 assigned to VLAN 10, 5-12 assigned to VLAN 20, 13-19 assigned to VLAN 30 and 20-24 assigned to VLAN 40. He would like all the gear on VLAN 30 to have the ablity to talk to all of the other VLANS, but VLAN 40 should not be allowed to talk with any other VLAN. Trunking would do no good here since the switch isn't connected to anything and you can only assign one VLAN per port.
Is there a way to do this within the stand alone switch? The only possible way I could think of would be to ensure that each VLAN has an assigned IP number (subnet) and doing this through access lists.
am having a switch 3860 it is configured dhcp , dns i want to change those dhcp , dns, what are the command that is use to reconfigure it
View 1 Replies View Related