I have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedI have two switches, a 2960 (sw01) and a 2948 (sw02). The sw01 is trunking via dot1q on Gi0/24 to sw02 on 2/48. Why are VLANs 2-4 not active on sw02?
sw01#sh int Gi0/24 trunk
Port Mode Encapsulation Status Native vlan
Gi0/24 auto 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/24 1-4094
[code].....
How can i add two data vlans on cisco 2960 on one interfase? i have 3 mac adresses on one interfase: one PC, one ipphone and one XP virtual machine(VM). PC and VM are in one data vlan and phone is in voice vlan. i need to place the VM in another data vlan is it possible? if so could you give me a link or place information here.
View 2 Replies View RelatedI recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?
View 1 Replies View RelatedI have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
On a low-end switch like a 2960 the maximum VLANs is 255, as shown in the output of VTP status:
Maximum VLANs supported locally : 255
Number of existing VLANs : 245
When the VTP mode is changed to transparent, VLANs from the extended range can be added without increasing the number of existing VLANs - e.g. if I create VLANs 3000 - 4000 the number of existing VLANs is still listed as 245.
If MST is used to cut down on the number of spanning-tree instances - and assuming propagation of VLAN configuration via VTP is not required - is there any downside to using transparent-mode VTP to increase the number of available VLANs? It does feel like I'm cheating the maximum listed in the datasheet.
I've just started a new job after a couple of years not touching cisco gear and been pitched in... My new employer has a network that's Juniper based. We've inherited a load of Cisco switches as part of the deal for hosting matches during the Rugby world cup (plus a load of Aruba wireless gear that promises to be my very own special millstone, but that's bye the bye.)
My task is to hang these catalyst 2960's onto our existing infrastructure via fibre connections.
On the Juniper switch, there are four vlans being pushed to the port the cisco's hooked into: Code...
Switch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies View RelatedI have a above said switch at my remote office (600KM) which is connected with L2 Point to Point leased line. Both the ends I have Cisco 3950 catalyst switches with Vlans configured at both the ends. Now, for obvious reasons I should remove the other end 3950 switch and replace with Cisco 2950 switch. The other end 3950 is having 4 Vlans configured on 4 ports. Now my requirement is, I should configure 3 Vlans (one for P2P, one for 10 Desktops and one for to bring traffic from other network).
View 1 Replies View RelatedI can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
I was assigned a task to configure an SG300-28P to have 3 different vlans.Now on VLAN1 their will be only one device configured with static IP 192.168.0.230,On the other 2 VLANS there will be a separate router connected on each one of them and will also act as a DHCP server.
View 4 Replies View RelatedI would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies View RelatedWe need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies View RelatedUsing Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies View RelatedI have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies View RelatedMy problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
I have Catalyst 3750 running IOS version c3750-ipservicesk9-mz.122-55.SE.bin. I have an access port that connects to a Redhat Linux version 5.4 64 bits machine. When I perform a "show mac address-table interface g1/0/3" where the redhat machine is connected to, I see two mac addresses on this access port. One of the mac addresses, 0025.9006.4898, belongs the the redhat machine. the other mac address, I have no idea where it comes from. I tried to perform clear mac address-table dynamic g1/0/3 several times but it does not work either.
View 8 Replies View RelatedI'm unable to apply a policing limit in a switchport of the CISCO861 router. This is my configuration:interface FastEthernet0, service-policy input wired-input,service-policy output wired-output end.
View 3 Replies View RelatedI have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
I try change the configuration the port in the switch catalyst express 500, i need disable switch port port-security, a try with http://10.1.1.1/exec and save configuration with wr command, if a check the configuration de port is correct but i reboot the switch and check the configuration the port appear the switch port port-security configuration again.
View 3 Replies View RelatedCurrently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
Im trying to follow along documentation i see via train single videos and some online resources. I am trying to enable port security.I have a Catalyst 3546 XL when i type in "rtr1# switchport ?""port-security" is not only of the options to choose from. I have already set this as an access port.
View 4 Replies View RelatedI'm setting up a new 4900m running cat4500e-ipbase-mz.122-53.SG5.bin. I'm attempting to create Port-Channels as a Trunk for uplink to a 4503 running cat4500-ipbase-mz.122-37.SG1.bin.When I attempt the command "switchport trunk encapsulation dot1q" it errors out.
View 3 Replies View Related