I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Im trying to follow along documentation i see via train single videos and some online resources. I am trying to enable port security.I have a Catalyst 3546 XL when i type in "rtr1# switchport ?""port-security" is not only of the options to choose from. I have already set this as an access port.
View 4 Replies View RelatedAre any of the following commands supported on Nexus 5K switches when deployed with L3 card:
ip helper addressip forward-protocolip directed-broadcast
My Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor
SG01NX01# debug ip ospf 1 packets
SG01NX01# show debug
[Code].....
when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies View Relatedwhat is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedI am trying to modify the OSPF admin distance for a specific subnet under version 5.1(5) of the Nexus 7K, but this command does not appear to be available.
View 1 Replies View RelatedWe have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View Relatedtell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
What is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies View RelatedI have configured the ip telnet source-interface Loopback 0 command on a Nexus7010, but when I telnet to another device and do a show users, the ip address is of the closest interface to the device I telnet to, not the ip address of the Loopback. All interfaces are in vrf default. I am running 5.1(6) NXOS.
View 6 Replies View RelatedI have Catalyst 3750 running IOS version c3750-ipservicesk9-mz.122-55.SE.bin. I have an access port that connects to a Redhat Linux version 5.4 64 bits machine. When I perform a "show mac address-table interface g1/0/3" where the redhat machine is connected to, I see two mac addresses on this access port. One of the mac addresses, 0025.9006.4898, belongs the the redhat machine. the other mac address, I have no idea where it comes from. I tried to perform clear mac address-table dynamic g1/0/3 several times but it does not work either.
View 8 Replies View RelatedI'm unable to apply a policing limit in a switchport of the CISCO861 router. This is my configuration:interface FastEthernet0, service-policy input wired-input,service-policy output wired-output end.
View 3 Replies View RelatedI have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
I try change the configuration the port in the switch catalyst express 500, i need disable switch port port-security, a try with http://10.1.1.1/exec and save configuration with wr command, if a check the configuration de port is correct but i reboot the switch and check the configuration the port appear the switch port port-security configuration again.
View 3 Replies View RelatedI have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies View RelatedCurrently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
I'm setting up a new 4900m running cat4500e-ipbase-mz.122-53.SG5.bin. I'm attempting to create Port-Channels as a Trunk for uplink to a 4503 running cat4500-ipbase-mz.122-37.SG1.bin.When I attempt the command "switchport trunk encapsulation dot1q" it errors out.
View 3 Replies View RelatedOur customer has a Cisco ME3600X with the IOS me 360x-universalK9-mz.122-52.EY3.They are saying that is not possible to configure the "switchport port-security mac-address sticky" in the interfaces and want to know whether any additional license is needed.As far as I know there isn't any extra license to activate this feature and also I believe the ME3600 switch should have this feature with the universal IOS, isn't that right?
View 1 Replies View RelatedI have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View RelatedWe are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedI have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View Relatedwe are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies View RelatedWe have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
What is the correct command to check the hardware of a Nexus 5020, like the show Inventori, show diag etc Used the same or is there a specific one for these items?
View 2 Replies View RelatedWhere is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies View RelatedDoes the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View Related