Cisco Switching/Routing :: Equivalent Command To Configure On Nexus 5596
Jun 21, 2012what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Equivalent Command To Show Int Summary On The Nexus 7000?
Nov 20, 2011tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
Cisco Switching/Routing :: Configure Nexus 5596 To Support Proper QoS For EF At The Core?
Feb 23, 2012I am deploying a pair of Nexus 5596's with 3750 POE switches in the closets. I'm looking for a best practice as how to configure the Nexus 5596 to support proper QoS for EF at the core.
View 6 Replies View RelatedCisco WAN :: Setup Nexus (5596 Running NX-OS 5.1(3)N2(1)) To Use IP Ospf Name-lookup Command?
Aug 8, 2012I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 5596 UP L3 OSPF
Jan 3, 2013I have 2 Nexus 5596UPs with a layer 3 cards that are exhibiting some very peculiar behavior. The systems are running 5.1(3)N1(1).I have configured 2 VRF contexts each running their own OSPF process. There is a static gateway of last resort configured on each VRF, which is to an upstream pair of 5585X's in Active/Active. Each OSPF process has the "default-information originate always" command configured, however, backbone neighbors are not recieving a gateway of last resort from the 5596UPs. The applicable configurations are show below. All other routing information is passing correctly between devices in the network. This network is not production, it is a proof of concept for a larger implementation.
View 26 Replies View RelatedCisco Switching/Routing :: Netflow On Nexus 5596
Oct 23, 2011Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 5596 - VPC Keep Alive Over Non-VPC Trunk
Mar 19, 2012We have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies View RelatedCisco Switching/Routing :: Nexus 5596 N55-M160L3-V2 Module
Oct 31, 2012Can Nexus 5596 support more than 1 N55-M160L3-V2 layer 3 module?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 5596 / 2248 TP - Compatibility With SFP-10G-SR
Jan 31, 2012I am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies View RelatedCisco Switching/Routing :: 5596 Nexus In-band Management With SVI
Apr 16, 2013i have: two nexus 5596 connected each other the mgmt0 is NOT in use SVI for keepalives with IP address and /30 netmask vpc-keepalives running over fiber in e1/1. this works well uplinks to datacenter distribution switch (Cat 6500 VSS) over fiber on port-channel 1 (e1/2 and e1/10), also carrying the management VLAN (vlan 14). SVI with an IP address for management purposes
I can't get this to work. i can ping my whole network from the nexus, but not the nexus from my network. also pinging inside the mgmt vlan is not possible.
Cisco Switching/Routing :: Reason For L3 Not Ready In Nexus 5596
Dec 19, 2012we have configured VpC between two Nexus 5596, for Vpc-Keep-alive-link we configured L3 interface with 1G (GLC-T) ,it shows the below status message "L3 not Ready" with interface LED glows in Yellow in color. is this a physical layer problem
Ethernet VLAN Type Mode Status Reason Speed Po Ch
Eth1/17 -- eth routed down L3 not ready 1000(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
[code].....
Cisco Switching/Routing :: ERSPAN On Nexus 5596 HSRP Pair
Jul 6, 2012We have HSRP between NexusA and NexusB with access layer switches connecting to the core using VPC, We are trying to setup a VAM server Voice recording for Siemens phones. We need to span all voice vlan and point it to the VAM server the VAM server connects to a 3750 Stack considering the amount of traffic multiple span session can generate I plan to move the server to the Nexus directly and run a Local Span Session.
1- As we have two Nexus running HSRP and VAM server only connects physically to one NexusA (I can run local span on that nexusA) the Second NexusB is not directly connected to the VAM server I plan to run ERSPAN so if this is the best design and which path will the span traffic take from Nexus B to NexusA will it go through the access layer switches depending on the vlans allowed on the uplinks or will it go through the 20 Gig uplink between the two Nexus allowing all vlans (VPN peer links) ? WE have approximately 10 voice vlans, Do we an example config for ERSPAN session where the source are vlans (As I am for fimilliar with RSPAN) ?
Cisco Switching/Routing :: Redistributing EIGRP Using Route Map Nexus 5596 L3
Dec 18, 2011this is a Nexus 5596 L3 with the latest code:
It looks like the deny statement is not working as I can see all routes I am redistributing. I even did a deny on a specific route and I still see it in the routing table on another router in the autonomous system.The same below works fine on IOS platform. [code]
Cisco Switching/Routing :: Nexus 2248 / N 5596 - AA Version Mismatch
Jan 27, 2013I have a pair of 5596 running in a vPC with Nexus 2248 connected to each N5596. When I do the command "show fex" I get the following output on the 2nd 5596
Number Description State Model Serial
------------------------------------------------------------------------
101 FEX101 AA Version Mismatch N2K-C2248TP-E-1GE SSI16390705
102 FEX102 AA Version Mismatch N2K-C2248TP-E-1GE SSI163704AD
122 FEX122 Online N2K-C2232PP-10GE SSI16370195
I'm running version 5.1(3)N1(1) on both of the 5K's. I have looked through all the configuration and I am not understanding why I am getting this error. I have tried to look it up on [URL], but not having a ton of luck.
Cisco Switching/Routing :: Nexus 5596 Giving Error In Connection
Aug 28, 2012I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
Cisco Switching/Routing :: Nexus 5596 - Are VPC Peer Links Locally Significant
Mar 17, 2013I currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 5548 Or 5596 To Replace Cat 3750 And 4507R?
Feb 17, 2012Any experience interoperating Nexus 5548 or 5596 with Catalyst 3750 or 4507R?
We're looking into Nexus to replace these switches in the long run.
Cisco Switching/Routing :: Nexus 5596 - Remove Switch-Profile Without Interruption
Jun 11, 2013i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", for example. Since NX-OS Release 5.2(1)N1(1) there is a new command
switch(config-sync)# no switch-profile abc profile-onlyprofile-only—Deletes the switch profile without the local configuration.
[URL]
Cisco Switching/Routing :: Phone Connects To 3750-A / Nexus 5596 Does Not Support RSPAN
Feb 20, 2013the phone connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that connects to another access layer 3750-B switch.(VTP mode client)
For voice recording I need to setup RSPAN and the nexus5596 does not support RSPAN will the following have any impact on the nexus
IF I move the 3750-B to VTP server mode and run the command remote span on the VLan I need to Rspan its going to update the VTP data base in short it will update the vlan.dat file for all the switch in that VTP domain.
AS the vtp update reaches the nexus saying there is a change (keeping in mind the nexus does not support rspan not sure hows its going to handle that request and how its going to update its vlan.dat file)
Is it going to incremment the VTP revision number? can it crash the vlan.dat file on the nexus ? or do nothing and ignore the update and stop the update from proceeding to the 3750 A switch?
Cisco Switching/Routing :: Nexus 7K No Switchport Command Available?
Mar 22, 2013I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
Cisco Switching/Routing :: IP Helper Command On Nexus 5K
Jan 1, 2012Are any of the following commands supported on Nexus 5K switches when deployed with L3 card:
ip helper addressip forward-protocolip directed-broadcast
Cisco Switching/Routing :: Debug Command Not Working On Nexus 5548?
Nov 15, 2012My Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor
SG01NX01# debug ip ospf 1 packets
SG01NX01# show debug
[Code].....
Cisco Switching/Routing :: Getting Nexus 5000 Command (default Interface X / X)
Jun 26, 2012when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies View RelatedCisco WAN :: What Is The Equivalent Command On IOS-XR 4.3.0
Jan 10, 2013I want to configure this:
ip vrf TEST
rd 65500:1
route-target export 65500:1
route-target import 65500:1
bgp next-hop Loopback500
on IOS-XR 4.3.0
What is the equivalent command on IOS-XR?
route-policy TEST1
set next-hop 1.1.1.1
vrf TEST
address-family ipv4 unicast
import route-policy TEST1
Cisco Switching/Routing :: OSPF Subnet Admin Distance Command On Nexus 7K
Jun 20, 2012I am trying to modify the OSPF admin distance for a specific subnet under version 5.1(5) of the Nexus 7K, but this command does not appear to be available.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7000 SWACT Show Redundancy Command
Nov 9, 2012We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7010 - Command For Restoring The Running Configuration
Apr 29, 2012What is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies View RelatedCisco Switching/Routing :: Nexus 7010 IP Telnet Source-interface Command Not Working
Aug 20, 2012I have configured the ip telnet source-interface Loopback 0 command on a Nexus7010, but when I telnet to another device and do a show users, the ip address is of the closest interface to the device I telnet to, not the ip address of the Loopback. All interfaces are in vrf default. I am running 5.1(6) NXOS.
View 6 Replies View RelatedCisco Application :: Passdetect Command Equivalent In CSS 11503?
Sep 11, 2011what is the "passdetect" command equivalent in CSS 11503 load balancer. software version 8.20.
View 3 Replies View RelatedCisco Infrastructure :: 5510 - Equivalent Of Netstat Command On Router
Jul 30, 2003Is there any way to see on what ports a Cisco 5510router is listening to just like a "netstat -an" on UNIX would do. I could easily do a portscan to give me this report but would prefer having the information through a show command.
View 4 Replies View RelatedCisco Switching/Routing :: 7600 / ES20+ Configure Global Command Mls Qos
Dec 18, 2012ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
Cisco Switching/Routing :: How To Configure Nexus 5K
Oct 26, 2011How to configure a nexus 5K?
View 3 Replies View RelatedCisco Switching/Routing :: Configure Sub Interface For Nexus 7k?
Jan 11, 2013how do we configure sub interface for nexus 7k?do we have to issue ma-address command under physical interface and than configure subinterface? if yes than what do we have to type the mac address for "mac-address" command?I can doing and than configure subinterface but the interface/subinterface didn't come up. do we have to bounce it couple times to bringe it up?
View 1 Replies View Related