Cisco Switching/Routing :: Nexus 5596 - VPC Keep Alive Over Non-VPC Trunk
Mar 19, 2012
We have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies
ADVERTISEMENT
May 5, 2013
We setup two n7K as core switches in our network. We configure VPc peer link as well successfully. We are using mgmt interface of supervisors as a peer keep alive interface, so what happen when this keep alive gets down? Are we loss Vpc peer link between both nexus 7 K?
View 4 Replies
View Related
Apr 19, 2013
I have a pair of Nexus 5548UPs that have some high priority servers running on them. Servers are ESX hosts running Nexus 1000v's. Each host has multple connections in a VPC to both 5548s. We have been having intermittant ping loss and slowness of traffic to the VM's on these hosts. I was poking around trying to figure out what the issue could be and found that the peer-keepalive command was not set to send the heart beat across the mgmt0 interface. I would like to change this to point it accross the mgmt0 interface. Any tips or advice for me on making this change with production servers running on the switches? I do not want to cause any loss to any systems when I make this change. [Code] ..........
View 3 Replies
View Related
Jan 3, 2013
I have 2 Nexus 5596UPs with a layer 3 cards that are exhibiting some very peculiar behavior. The systems are running 5.1(3)N1(1).I have configured 2 VRF contexts each running their own OSPF process. There is a static gateway of last resort configured on each VRF, which is to an upstream pair of 5585X's in Active/Active. Each OSPF process has the "default-information originate always" command configured, however, backbone neighbors are not recieving a gateway of last resort from the 5596UPs. The applicable configurations are show below. All other routing information is passing correctly between devices in the network. This network is not production, it is a proof of concept for a larger implementation.
View 26 Replies
View Related
Oct 23, 2011
Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 Replies
View Related
Oct 31, 2012
Can Nexus 5596 support more than 1 N55-M160L3-V2 layer 3 module?
View 4 Replies
View Related
Jan 31, 2012
I am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies
View Related
Apr 16, 2013
i have: two nexus 5596 connected each other the mgmt0 is NOT in use SVI for keepalives with IP address and /30 netmask vpc-keepalives running over fiber in e1/1. this works well uplinks to datacenter distribution switch (Cat 6500 VSS) over fiber on port-channel 1 (e1/2 and e1/10), also carrying the management VLAN (vlan 14). SVI with an IP address for management purposes
I can't get this to work. i can ping my whole network from the nexus, but not the nexus from my network. also pinging inside the mgmt vlan is not possible.
View 7 Replies
View Related
Dec 19, 2012
we have configured VpC between two Nexus 5596, for Vpc-Keep-alive-link we configured L3 interface with 1G (GLC-T) ,it shows the below status message "L3 not Ready" with interface LED glows in Yellow in color. is this a physical layer problem
Ethernet VLAN Type Mode Status Reason Speed Po Ch
Eth1/17 -- eth routed down L3 not ready 1000(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
[code].....
View 10 Replies
View Related
Jul 6, 2012
We have HSRP between NexusA and NexusB with access layer switches connecting to the core using VPC, We are trying to setup a VAM server Voice recording for Siemens phones. We need to span all voice vlan and point it to the VAM server the VAM server connects to a 3750 Stack considering the amount of traffic multiple span session can generate I plan to move the server to the Nexus directly and run a Local Span Session.
1- As we have two Nexus running HSRP and VAM server only connects physically to one NexusA (I can run local span on that nexusA) the Second NexusB is not directly connected to the VAM server I plan to run ERSPAN so if this is the best design and which path will the span traffic take from Nexus B to NexusA will it go through the access layer switches depending on the vlans allowed on the uplinks or will it go through the 20 Gig uplink between the two Nexus allowing all vlans (VPN peer links) ? WE have approximately 10 voice vlans, Do we an example config for ERSPAN session where the source are vlans (As I am for fimilliar with RSPAN) ?
View 3 Replies
View Related
Dec 18, 2011
this is a Nexus 5596 L3 with the latest code:
It looks like the deny statement is not working as I can see all routes I am redistributing. I even did a deny on a specific route and I still see it in the routing table on another router in the autonomous system.The same below works fine on IOS platform. [code]
View 5 Replies
View Related
Jan 27, 2013
I have a pair of 5596 running in a vPC with Nexus 2248 connected to each N5596. When I do the command "show fex" I get the following output on the 2nd 5596
Number Description State Model Serial
------------------------------------------------------------------------
101 FEX101 AA Version Mismatch N2K-C2248TP-E-1GE SSI16390705
102 FEX102 AA Version Mismatch N2K-C2248TP-E-1GE SSI163704AD
122 FEX122 Online N2K-C2232PP-10GE SSI16370195
I'm running version 5.1(3)N1(1) on both of the 5K's. I have looked through all the configuration and I am not understanding why I am getting this error. I have tried to look it up on [URL], but not having a ton of luck.
View 3 Replies
View Related
Aug 28, 2012
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
View 2 Replies
View Related
Jun 21, 2012
what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies
View Related
Feb 23, 2012
I am deploying a pair of Nexus 5596's with 3750 POE switches in the closets. I'm looking for a best practice as how to configure the Nexus 5596 to support proper QoS for EF at the core.
View 6 Replies
View Related
Mar 17, 2013
I currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies
View Related
Feb 17, 2012
Any experience interoperating Nexus 5548 or 5596 with Catalyst 3750 or 4507R?
We're looking into Nexus to replace these switches in the long run.
View 1 Replies
View Related
Jun 11, 2013
i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", for example. Since NX-OS Release 5.2(1)N1(1) there is a new command
switch(config-sync)# no switch-profile abc profile-onlyprofile-only—Deletes the switch profile without the local configuration.
[URL]
View 2 Replies
View Related
Feb 20, 2013
the phone connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that connects to another access layer 3750-B switch.(VTP mode client)
For voice recording I need to setup RSPAN and the nexus5596 does not support RSPAN will the following have any impact on the nexus
IF I move the 3750-B to VTP server mode and run the command remote span on the VLan I need to Rspan its going to update the VTP data base in short it will update the vlan.dat file for all the switch in that VTP domain.
AS the vtp update reaches the nexus saying there is a change (keeping in mind the nexus does not support rspan not sure hows its going to handle that request and how its going to update its vlan.dat file)
Is it going to incremment the VTP revision number? can it crash the vlan.dat file on the nexus ? or do nothing and ignore the update and stop the update from proceeding to the 3750 A switch?
View 1 Replies
View Related
Feb 6, 2013
So I took a laptop with wireshark and plugged it into a nexus 5000 port that is configured as a trunk with 3 vlans allowed on it. The laptop was seeing all kinds of traffic on the wire, most of it was not involving my laptop.
For example: Server A VLAN 10= 10.10.10.1 Server B VLAN 20= 10.20.20.1 and wireshark laptop is plugged into a trunk port which is allowing those vlan's. The vlan's are routable.
10.10.10.3 is seeing the entire conversation when 10.10.10.1 backs up 10.20.20.1 even though it has no reason to see it. It is as if the trunk is spanning traffic to the laptop port. No span is setup however. It's really weird. This is not just broadcast traffic, but actual tcp taffic between Server A and B. Why would a trunk port see traffic between 2 other servers talking to each other on the vlan.
Trunk port configuration below:
Interface Ethernet 141/1/3
switchport mode trunk
switchport trunk allowed vlan 10, 20
View 5 Replies
View Related
Oct 31, 2012
I want to prioritize egress voice traffic across a trunk terminated on an F1 module, N7K-F132XP-15. I am unsure about the setup; according to the "show interface capabilities" F1 interfaces support 8 egress queues, while the Nexus QoS documentation provides configuration referencing 4 queues. In addition, I am not clear about the relevance of network-qos on F1 queueing setup.
View 1 Replies
View Related
Feb 9, 2011
I'm not sure if I'm missing something basic here however i though that I'd ask the question. I recieved a request from a client who is trying to seperate traffic out of a IBM P780 - one set of VIO servers/clients (Prod) is tagged with vlan x going out LAG 1 and another set of VIO server/clients (Test) is tagged with vlan y and z going out LAG 2. The problem is that the management subnet for these devices is on one subnet.
The infrastructure is the host device is trunked via LACP etherchannel to Nexus 2148TP(5010) which than connects to the distribution layer being a Catalyst 6504 VSS. I have tried many things today, however I feel that the correct solution to get this working is to use an Isolated trunk (as the host device does not have private vlan functionality) even though there is no requirement for hosts to be segregated. I have configured:
1. Private vlan mapping on the SVI;
2. Primary vlan and association, and isolated vlan on Distribution (6504 VSS) and Access Layer (5010/2148)
3. All Vlans are trunked between switches
4. Private vlan isolated trunk and host mappings on the port-channel interface to the host (P780).
I haven't had any luck. What I am seeing is as soon as I configure the Primary vlan on the Nexus 5010 (v5.2) (vlan y | private-vlan primary), this vlan (y) does not forward on any trunk on the Nexus 5010 switch, even without any other private vlan configuration. I believe this may be the cause to most of the issues I am having. Has any one else experienced this behaviour. Also, I haven't had a lot of experience with Private Vlans so I might be missing some fundamentals with this configuration.
View 3 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Feb 27, 2011
can assist me with some vPC design best practice. I'm trying to get my head wrapped around and build some engineering/configs together before my equipment arrives. I have two nexus 7010 boxes arriving soon.I will go ahead and configure the peer link using two 10g ports between the 7k's. Now how do I go ahead and configure the keepalive link.
1. use a copper dedicated single link using the mgmt ports on the supervisor for the keepalive?
2. use a copper port from 10/100/1000 line card (N7K-M148GT-11) for the keepalive?
Also this network will have a dedicated mgmt switch for all the devices to be managed. If I go ahead with number one (above), how will I use that port to manage that device?
View 14 Replies
View Related
Jan 28, 2013
Does ACS v4.2 support the addition of the Nexus switches? We have a few new Nexus devices that have been added to ACS, but cannot be accessed successfully. A msg re: role based authentication is received. Do I have to do something special in ACS to support this?
Nexus 5596 v5.1(3)N2(1)
View 4 Replies
View Related
Nov 19, 2012
I am running LMS 3.2 and can not see the Nexus 5596 / ME-3600X-24FS-M Cisco switches on Cisco works LMS 3.2. Where I need them most is DFM the devices come up as unknown. An example below 10.125.202.1 is NExus 5596 and the rest are ME3600.
208.10.125.202.1UnknownN/AN/A209.10.115.1.4UnknownN/AN/A210.10.115.1.3UnknownN/AN/A211.10.115.1.2UnknownN/AN/A212.10.115.1.1UnknownN/AN/A
going through the article below looks like its not supported
[URL]
What are the options I have next ? Can I upgrade to LMS 3.3 or only do an upgrade for DFM ?
Want to avoid LMS 4 as that's an installation from scratch.
View 2 Replies
View Related
Mar 23, 2012
I want to know how to retrieve the complete configuration for a Nexus via the snmpwalk or snmpget commands...
View 6 Replies
View Related
Aug 8, 2012
I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies
View Related
Apr 17, 2012
I need to implement LACP HP servers mostly DL 380 g7 with Intel based dual port with two types of Cisco equipment first scenario server connected to 3750x stack of 4 switch's .second scenario same server type connected to two Cisco Nexsus 5596 . My question regarding two type of connection.Is it possible to do active active ?Would it give fault tolerance ?With HP LACP implementation is there known issue or should i expect latency with such configuration?What is the maximal lag- channel group that is possible per type?
View 1 Replies
View Related
Dec 14, 2011
For a simple 4x sites design for backup consolidation (3x sites connected to one central site), does the design in the attached JPEG make sense and is the configuration achievable using the specified parts?
Brief Explanation:
- Each site is to have servers with 2x 10Gb/s Ethernet (both teamed/bonded/etc) and one NIC on each of the 2x switches in the site (if possible). Each site will also have 2x Cisco Nexus 5596UP Switch (though the P version may be used instead of the UP).
- Two of the sites are within 10KM of the central site
- The last site is about 35KM from the central site
- It is required to have a minimum bandwidth of 10Gb/s between any site and the central site
- I have specified 10Gb/s LW SFP+ and 10Gb/s LW SFP+ (for the 2x 10KM and 1x 35KM sites)
- are there any special licenses needed?
- as asked before, can such a "simple" design work as-is?
- what sort of single-mode fiber would fit the bill (especially for the 40KM link) - 9nm?
View 2 Replies
View Related
Apr 22, 2013
I have pair of 5596 switches in vPC. One host say "HOST A" is connected to the primary vPC peer and other "HOST B" on secondary vPC peer.Both are in same VLAN 10. Both hosts are vpc orphan ports as their NIC is configured in active/standby mode.I have configured span session on both vPC peers with span source as VLAN 10 in rx mode.Span destination is connected to secondary vPC peer. The issue here is that I am not able to capture the traffic originating from HOST A destined to HOST B which is traversing vPC peer-link.Same issue occurs for the traffic in reverse way and span destination on primary vPC peer. In a nutshell, any traffic which crosses vPC peer-link is not getting captured.
What could be the issue and is there any solution for it. Below mentioned is the span config and relevant interfaces. [code]
View 4 Replies
View Related
Feb 23, 2011
We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies
View Related
Mar 15, 2013
I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
View 12 Replies
View Related
