Cisco Switching/Routing :: Netflow On Nexus 5596
Oct 23, 2011Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 RepliesNet flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 RepliesI have 2 Nexus 5596UPs with a layer 3 cards that are exhibiting some very peculiar behavior. The systems are running 5.1(3)N1(1).I have configured 2 VRF contexts each running their own OSPF process. There is a static gateway of last resort configured on each VRF, which is to an upstream pair of 5585X's in Active/Active. Each OSPF process has the "default-information originate always" command configured, however, backbone neighbors are not recieving a gateway of last resort from the 5596UPs. The applicable configurations are show below. All other routing information is passing correctly between devices in the network. This network is not production, it is a proof of concept for a larger implementation.
View 26 Replies View RelatedWe have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies View RelatedCan Nexus 5596 support more than 1 N55-M160L3-V2 layer 3 module?
View 4 Replies View RelatedI am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies View Relatedi have: two nexus 5596 connected each other the mgmt0 is NOT in use SVI for keepalives with IP address and /30 netmask vpc-keepalives running over fiber in e1/1. this works well uplinks to datacenter distribution switch (Cat 6500 VSS) over fiber on port-channel 1 (e1/2 and e1/10), also carrying the management VLAN (vlan 14). SVI with an IP address for management purposes
I can't get this to work. i can ping my whole network from the nexus, but not the nexus from my network. also pinging inside the mgmt vlan is not possible.
we have configured VpC between two Nexus 5596, for Vpc-Keep-alive-link we configured L3 interface with 1G (GLC-T) ,it shows the below status message "L3 not Ready" with interface LED glows in Yellow in color. is this a physical layer problem
Ethernet VLAN Type Mode Status Reason Speed Po Ch
Eth1/17 -- eth routed down L3 not ready 1000(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
[code].....
We have HSRP between NexusA and NexusB with access layer switches connecting to the core using VPC, We are trying to setup a VAM server Voice recording for Siemens phones. We need to span all voice vlan and point it to the VAM server the VAM server connects to a 3750 Stack considering the amount of traffic multiple span session can generate I plan to move the server to the Nexus directly and run a Local Span Session.
1- As we have two Nexus running HSRP and VAM server only connects physically to one NexusA (I can run local span on that nexusA) the Second NexusB is not directly connected to the VAM server I plan to run ERSPAN so if this is the best design and which path will the span traffic take from Nexus B to NexusA will it go through the access layer switches depending on the vlans allowed on the uplinks or will it go through the 20 Gig uplink between the two Nexus allowing all vlans (VPN peer links) ? WE have approximately 10 voice vlans, Do we an example config for ERSPAN session where the source are vlans (As I am for fimilliar with RSPAN) ?
this is a Nexus 5596 L3 with the latest code:
It looks like the deny statement is not working as I can see all routes I am redistributing. I even did a deny on a specific route and I still see it in the routing table on another router in the autonomous system.The same below works fine on IOS platform. [code]
I have a pair of 5596 running in a vPC with Nexus 2248 connected to each N5596. When I do the command "show fex" I get the following output on the 2nd 5596
Number Description State Model Serial
------------------------------------------------------------------------
101 FEX101 AA Version Mismatch N2K-C2248TP-E-1GE SSI16390705
102 FEX102 AA Version Mismatch N2K-C2248TP-E-1GE SSI163704AD
122 FEX122 Online N2K-C2232PP-10GE SSI16370195
I'm running version 5.1(3)N1(1) on both of the 5K's. I have looked through all the configuration and I am not understanding why I am getting this error. I have tried to look it up on [URL], but not having a ton of luck.
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedI am deploying a pair of Nexus 5596's with 3750 POE switches in the closets. I'm looking for a best practice as how to configure the Nexus 5596 to support proper QoS for EF at the core.
View 6 Replies View RelatedI currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies View RelatedAny experience interoperating Nexus 5548 or 5596 with Catalyst 3750 or 4507R?
We're looking into Nexus to replace these switches in the long run.
i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", for example. Since NX-OS Release 5.2(1)N1(1) there is a new command
switch(config-sync)# no switch-profile abc profile-onlyprofile-only—Deletes the switch profile without the local configuration.
[URL]
the phone connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that connects to another access layer 3750-B switch.(VTP mode client)
For voice recording I need to setup RSPAN and the nexus5596 does not support RSPAN will the following have any impact on the nexus
IF I move the 3750-B to VTP server mode and run the command remote span on the VLan I need to Rspan its going to update the VTP data base in short it will update the vlan.dat file for all the switch in that VTP domain.
AS the vtp update reaches the nexus saying there is a change (keeping in mind the nexus does not support rspan not sure hows its going to handle that request and how its going to update its vlan.dat file)
Is it going to incremment the VTP revision number? can it crash the vlan.dat file on the nexus ? or do nothing and ignore the update and stop the update from proceeding to the 3750 A switch?
Ive tried to configure NetFlow on layer 2 without success. I configured the recondmonitorexporter like the configuration guide said. but still i dont receive any netflow traffic. I checked the firewall on the VM and it looks fine.
i have done the command under the ethernet interface :" layer2-switch flow monitor TEST input" - for layer2 input.
How to get a summary of netflow statistics on NX-OS? On IOS you could do sh ip cache flow which would show what I need? Can't find a similar command on the Nexus Platform.
View 4 Replies View RelatedI can't seem to find any information on the Nexus 5000 support of netflow. I assume that means it doesn't do netflow.
View 5 Replies View RelatedAny major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
Does ACS v4.2 support the addition of the Nexus switches? We have a few new Nexus devices that have been added to ACS, but cannot be accessed successfully. A msg re: role based authentication is received. Do I have to do something special in ACS to support this?
Nexus 5596 v5.1(3)N2(1)
I am running LMS 3.2 and can not see the Nexus 5596 / ME-3600X-24FS-M Cisco switches on Cisco works LMS 3.2. Where I need them most is DFM the devices come up as unknown. An example below 10.125.202.1 is NExus 5596 and the rest are ME3600.
208.10.125.202.1UnknownN/AN/A209.10.115.1.4UnknownN/AN/A210.10.115.1.3UnknownN/AN/A211.10.115.1.2UnknownN/AN/A212.10.115.1.1UnknownN/AN/A
going through the article below looks like its not supported
[URL]
What are the options I have next ? Can I upgrade to LMS 3.3 or only do an upgrade for DFM ?
Want to avoid LMS 4 as that's an installation from scratch.
I want to know how to retrieve the complete configuration for a Nexus via the snmpwalk or snmpget commands...
View 6 Replies View RelatedI was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies View RelatedI need to implement LACP HP servers mostly DL 380 g7 with Intel based dual port with two types of Cisco equipment first scenario server connected to 3750x stack of 4 switch's .second scenario same server type connected to two Cisco Nexsus 5596 . My question regarding two type of connection.Is it possible to do active active ?Would it give fault tolerance ?With HP LACP implementation is there known issue or should i expect latency with such configuration?What is the maximal lag- channel group that is possible per type?
View 1 Replies View Related For a simple 4x sites design for backup consolidation (3x sites connected to one central site), does the design in the attached JPEG make sense and is the configuration achievable using the specified parts?
Brief Explanation:
- Each site is to have servers with 2x 10Gb/s Ethernet (both teamed/bonded/etc) and one NIC on each of the 2x switches in the site (if possible). Each site will also have 2x Cisco Nexus 5596UP Switch (though the P version may be used instead of the UP).
- Two of the sites are within 10KM of the central site
- The last site is about 35KM from the central site
- It is required to have a minimum bandwidth of 10Gb/s between any site and the central site
- I have specified 10Gb/s LW SFP+ and 10Gb/s LW SFP+ (for the 2x 10KM and 1x 35KM sites)
- are there any special licenses needed?
- as asked before, can such a "simple" design work as-is?
- what sort of single-mode fiber would fit the bill (especially for the 40KM link) - 9nm?
I have pair of 5596 switches in vPC. One host say "HOST A" is connected to the primary vPC peer and other "HOST B" on secondary vPC peer.Both are in same VLAN 10. Both hosts are vpc orphan ports as their NIC is configured in active/standby mode.I have configured span session on both vPC peers with span source as VLAN 10 in rx mode.Span destination is connected to secondary vPC peer. The issue here is that I am not able to capture the traffic originating from HOST A destined to HOST B which is traversing vPC peer-link.Same issue occurs for the traffic in reverse way and span destination on primary vPC peer. In a nutshell, any traffic which crosses vPC peer-link is not getting captured.
What could be the issue and is there any solution for it. Below mentioned is the span config and relevant interfaces. [code]
I was trying to get Netflow setup on one of my 7K VDCs and ran into a problem. While netflow data was reaching the collector, IP src/dst information was not appearing in the analyzer tool. I could not see any information about conversations. So I contacted the company that makes the collector/analyzer and the directed me to a blog on their site and told me to setup the 7K exactly as it is described in the blog post. I did and a bit later the ip src/dst address information appeared. So the only difference between the two configurations was that in the first case I tried to define a record and in the second case, no record was defined and instead the orginial-netflow parameter was used in the "flow monitor" section. [code]
I referenced the document "Cisco Nexus 7000 Series NX-OS System Management Configuration Guide,Release 6.x", Chapter 19 - Configuring NetFlow.It's clear to me that I didn't do something right in defining my own record since that's really the only difference between the config that worked vs the config that didn't. However, the documentation I referenced doesn't really provide useful information about how to create a record (above and beyond what I can already see by typing '?' at the CLI).
For example, the "match" command makes no sense to me. Usually when you have a match command it is accompanied by some sort of ACL. In the "flow record" section a match command would be something like "match ipv4 source address" but that's it. What does that mean? Match anything that has a IPv4 source address?? That doesn't make much sense. The collect commands are equally as bewildering. If I want to define my own record (and not use the original-netflow parameter) what do I need to do in the "flow record" sub-configuration to get Nexus to send ip src/dst information to the collector (which, I would think, is basic information to send - what good is netflow data without it)?
We have Nexus 7000s configured for sampled netflow. We have tools that should reconstruct the sampled flow records for management displays. Most tools require the flow record, option and template to be sent in order to reconstruct the sampled flow record. We have captured some of this traffic and noticed that the template contains "SamplerMode": Unknown (1) [See Nexus 1-1.png]. Is this usual or have we not include commands required for proper operation? [code]
View 2 Replies View RelatedWe are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedI have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View Related