Cisco Switching/Routing :: Nexus 5596 N55-M160L3-V2 Module
Oct 31, 2012Can Nexus 5596 support more than 1 N55-M160L3-V2 layer 3 module?
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Nexus 5596 UP L3 OSPF
Jan 3, 2013I have 2 Nexus 5596UPs with a layer 3 cards that are exhibiting some very peculiar behavior. The systems are running 5.1(3)N1(1).I have configured 2 VRF contexts each running their own OSPF process. There is a static gateway of last resort configured on each VRF, which is to an upstream pair of 5585X's in Active/Active. Each OSPF process has the "default-information originate always" command configured, however, backbone neighbors are not recieving a gateway of last resort from the 5596UPs. The applicable configurations are show below. All other routing information is passing correctly between devices in the network. This network is not production, it is a proof of concept for a larger implementation.
View 26 Replies View RelatedCisco Switching/Routing :: Netflow On Nexus 5596
Oct 23, 2011Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 5596 - VPC Keep Alive Over Non-VPC Trunk
Mar 19, 2012We have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies View RelatedCisco Switching/Routing :: Nexus 5596 / 2248 TP - Compatibility With SFP-10G-SR
Jan 31, 2012I am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies View RelatedCisco Switching/Routing :: 5596 Nexus In-band Management With SVI
Apr 16, 2013i have: two nexus 5596 connected each other the mgmt0 is NOT in use SVI for keepalives with IP address and /30 netmask vpc-keepalives running over fiber in e1/1. this works well uplinks to datacenter distribution switch (Cat 6500 VSS) over fiber on port-channel 1 (e1/2 and e1/10), also carrying the management VLAN (vlan 14). SVI with an IP address for management purposes
I can't get this to work. i can ping my whole network from the nexus, but not the nexus from my network. also pinging inside the mgmt vlan is not possible.
Cisco Switching/Routing :: Reason For L3 Not Ready In Nexus 5596
Dec 19, 2012we have configured VpC between two Nexus 5596, for Vpc-Keep-alive-link we configured L3 interface with 1G (GLC-T) ,it shows the below status message "L3 not Ready" with interface LED glows in Yellow in color. is this a physical layer problem
Ethernet VLAN Type Mode Status Reason Speed Po Ch
Eth1/17 -- eth routed down L3 not ready 1000(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
[code].....
Cisco Switching/Routing :: ERSPAN On Nexus 5596 HSRP Pair
Jul 6, 2012We have HSRP between NexusA and NexusB with access layer switches connecting to the core using VPC, We are trying to setup a VAM server Voice recording for Siemens phones. We need to span all voice vlan and point it to the VAM server the VAM server connects to a 3750 Stack considering the amount of traffic multiple span session can generate I plan to move the server to the Nexus directly and run a Local Span Session.
1- As we have two Nexus running HSRP and VAM server only connects physically to one NexusA (I can run local span on that nexusA) the Second NexusB is not directly connected to the VAM server I plan to run ERSPAN so if this is the best design and which path will the span traffic take from Nexus B to NexusA will it go through the access layer switches depending on the vlans allowed on the uplinks or will it go through the 20 Gig uplink between the two Nexus allowing all vlans (VPN peer links) ? WE have approximately 10 voice vlans, Do we an example config for ERSPAN session where the source are vlans (As I am for fimilliar with RSPAN) ?
Cisco Switching/Routing :: Redistributing EIGRP Using Route Map Nexus 5596 L3
Dec 18, 2011this is a Nexus 5596 L3 with the latest code:
It looks like the deny statement is not working as I can see all routes I am redistributing. I even did a deny on a specific route and I still see it in the routing table on another router in the autonomous system.The same below works fine on IOS platform. [code]
Cisco Switching/Routing :: Nexus 2248 / N 5596 - AA Version Mismatch
Jan 27, 2013I have a pair of 5596 running in a vPC with Nexus 2248 connected to each N5596. When I do the command "show fex" I get the following output on the 2nd 5596
Number Description State Model Serial
------------------------------------------------------------------------
101 FEX101 AA Version Mismatch N2K-C2248TP-E-1GE SSI16390705
102 FEX102 AA Version Mismatch N2K-C2248TP-E-1GE SSI163704AD
122 FEX122 Online N2K-C2232PP-10GE SSI16370195
I'm running version 5.1(3)N1(1) on both of the 5K's. I have looked through all the configuration and I am not understanding why I am getting this error. I have tried to look it up on [URL], but not having a ton of luck.
Cisco Switching/Routing :: Nexus 5596 Giving Error In Connection
Aug 28, 2012I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
Cisco Switching/Routing :: Equivalent Command To Configure On Nexus 5596
Jun 21, 2012what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedCisco Switching/Routing :: Configure Nexus 5596 To Support Proper QoS For EF At The Core?
Feb 23, 2012I am deploying a pair of Nexus 5596's with 3750 POE switches in the closets. I'm looking for a best practice as how to configure the Nexus 5596 to support proper QoS for EF at the core.
View 6 Replies View RelatedCisco Switching/Routing :: Nexus 5596 - Are VPC Peer Links Locally Significant
Mar 17, 2013I currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 5548 Or 5596 To Replace Cat 3750 And 4507R?
Feb 17, 2012Any experience interoperating Nexus 5548 or 5596 with Catalyst 3750 or 4507R?
We're looking into Nexus to replace these switches in the long run.
Cisco Switching/Routing :: Nexus 5596 - Remove Switch-Profile Without Interruption
Jun 11, 2013i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", for example. Since NX-OS Release 5.2(1)N1(1) there is a new command
switch(config-sync)# no switch-profile abc profile-onlyprofile-only—Deletes the switch profile without the local configuration.
[URL]
Cisco Switching/Routing :: Phone Connects To 3750-A / Nexus 5596 Does Not Support RSPAN
Feb 20, 2013the phone connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that connects to another access layer 3750-B switch.(VTP mode client)
For voice recording I need to setup RSPAN and the nexus5596 does not support RSPAN will the following have any impact on the nexus
IF I move the 3750-B to VTP server mode and run the command remote span on the VLan I need to Rspan its going to update the VTP data base in short it will update the vlan.dat file for all the switch in that VTP domain.
AS the vtp update reaches the nexus saying there is a change (keeping in mind the nexus does not support rspan not sure hows its going to handle that request and how its going to update its vlan.dat file)
Is it going to incremment the VTP revision number? can it crash the vlan.dat file on the nexus ? or do nothing and ignore the update and stop the update from proceeding to the 3750 A switch?
Cisco Switching/Routing :: Nexus 7010 Module Failure?
Apr 11, 2012I'm currently getting a Nexus hardware failure at present.
switch %MODULE-2-MOD_DIAG_FAIL: Module 8 reported failure due to DEVICE POST/DIAG FAILURE in device 48
Cisco Switching/Routing :: SFP-GE-T Module Support On Nexus 5548?
Jan 7, 2013I am trying to install SFP-GE-T module on Nexus 5548UP Switch, but is giving the ‘SFP validation Failed’ error. The details of the switch is given below
Model : N5K-C5548UP-FA
The interface is configured with speed 1000 before inserting the module, still we are getting the same error. PFA logs for more details We have 8 Nos of SFP-GE-T modules , all are giving same error. We tried to insert the module on onboard as well as expansion module.
The same module is working fine on Cisco 3750X-24T-L Switch As per the Hardware installation guide , SFP-GE-T transciever is supported on N5K platform. Please extend your support in configuring SFP-GE-T module on N5K platform? We tried with SFP-GE-S module on the same switch , and the same is found working fine.
Cisco Switching/Routing :: Nexus 7k - Can't Update Epld On 10gb Module
Oct 19, 2011I am having trouble updating the epld image on the 10gb Module of Nexus 7k. we have two nexus and two 10gb module. Tried the other one and it worked fine. its jsut the first one that has problems with the epld image. i have tried on both the nexus on two different slots and still the same error.
I get the following error:
Chain connectivity is broken while upgrading the FPGA. (Error Number : 36)
Cisco Switching/Routing :: Adding N7KM132XP-12 Module To Nexus 7K Switch
Jul 31, 2012Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.
View 2 Replies View RelatedCisco Switching/Routing :: Connect IBM BladeCentre Switches With Nexus 2k Module?
Dec 18, 2012We are looking forward to implement IBM BladeCentre Swiches connectivity with Nexus 2k module.I would like to brief you about my network over as follows:
Coreswitch : 6513 ( Layer 3 switch + Spanning Tree root)
Nexus 5010 : Layer 2 switch
Nexus 2k 10G ports based module.
Currentl Solution : we want to connect the IBM Blade Switches (4) as demonstrated in the attached diagram which will be connected to Nexus 2k module as Ether-channel Access port.
Initially we been proposed by our vendor with this design and Now vendor is recommending us to connect the Blade switch etiher to Nexus 5k switch or directly to 6513 core-switches instead of Nexus 2k modules as they say Nexus 2k modules are only to connect the Edge devices .
We do not have ports available on Nexus 5010 to connect the cables from IBM Blade Centre Switches. Otherthan that, incase if we go ahead and connect the IBM Blade switches as access ether-channel access port with Nexus 2k module what are consequences we have to face realted Spanning tree or any other.
Cisco Switching/Routing :: Nexus 7000 Module Powered-dn Status
Jun 4, 2013One of our Nexus 7000 modules failed and generated the status below. Could this possibly be a hardware issue?
# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 10 Gbps Ethernet XL Module powered-dn
Mod Power-Status Reason
--- ------------ ---------------------------
1 powered-dn Unable to power up card (Power_OK not set)
Cisco Switching/Routing :: Nexus 7000 10Gig Card Not Seeing Transceiver Module?
Nov 13, 2011I'm unable to get the N7K-M108X2-12L 10 Gbps Ethernet XL Module within our Nexus 7009 chassis to recognise the individual X2-10GB-SR transceiver modules. I have the same issue on another 7009 chassis.If I perform a 'show interface'. I get the following output saying SFP not inserted.
-Ethernet3/5 is down (SFP not inserted)
-Dedicated Interface
-Belongs to Po51
-Hardware: 10000 Ethernet, address: 7081.0599.d458 (bia 7081.0599.d458)
I also get the same result if I issue the following command. Are their any additional features I need to enable? or would this be a license issue?
Have already tried different X2-10GB-SR modules, reloading the card, re seating the card. [code]
Cisco Switching/Routing :: Nexus 7K 6.1 Code And F2 Series Module - How To Enable Priority
Jul 7, 2012I have a 7K running 6.1 code, on F series line cards. I need to set it to prioritise DSCP EF marked traffic, that's all at this stage, but am unclear on the configuration steps required. The packets will already be marked, I just need to ensure they end up in a priority queue.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 55548UP - 1GE SFP Module Not Recognized In Fabric Extender
Oct 17, 2012we installed copper and fiber sfp modules in the 2232PP and none would link up. we pulled the sfp modules out and entered the speed 1000 command and re-inserted the module with no success. the same sfp modules works fine in every other cisco device. we must be missing something. running latest nx-os software.
COH-Nexus-02# sh int Eth101/1/1 status
--------------------------------------------------------------------------------
Port Name Status Vlan Duplex Speed Type
--------------------------------------------------------------------------------
[Code].....
Cisco Switching/Routing :: Can 10Gbase SFP+ Module Support 1GB Traffic On Nexus 5596T
Mar 20, 2013Can 10Gbase SFP+ module support 1GB traffic on a Nexus 5596T.
The module for 10Gb is Cisco SFP-10G-SR. My scenario is connecting the 10GB SFP+ module to an access switch 1GB fiber uplink, will this work?
Cisco Switching/Routing :: Connect ASA 5550 To Nexus 7K F2 Module Using Twinax Cable?
Mar 24, 2012can we connect ASA 5550 to Nexus 7K F2 module using twinax cable?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 7000 Voice Traffic Across Trunk Terminated On F1 Module
Oct 31, 2012I want to prioritize egress voice traffic across a trunk terminated on an F1 module, N7K-F132XP-15. I am unsure about the setup; according to the "show interface capabilities" F1 interfaces support 8 egress queues, while the Nexus QoS documentation provides configuration referencing 4 queues. In addition, I am not clear about the relevance of network-qos on F1 queueing setup.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Adding Nexus 5596 To ACS V4.2?
Jan 28, 2013Does ACS v4.2 support the addition of the Nexus switches? We have a few new Nexus devices that have been added to ACS, but cannot be accessed successfully. A msg re: role based authentication is received. Do I have to do something special in ACS to support this?
Nexus 5596 v5.1(3)N2(1)
Cisco :: Nexus 5596 / Metro 3600 Switches Do Not Come Up On LMS 3.2
Nov 19, 2012I am running LMS 3.2 and can not see the Nexus 5596 / ME-3600X-24FS-M Cisco switches on Cisco works LMS 3.2. Where I need them most is DFM the devices come up as unknown. An example below 10.125.202.1 is NExus 5596 and the rest are ME3600.
208.10.125.202.1UnknownN/AN/A209.10.115.1.4UnknownN/AN/A210.10.115.1.3UnknownN/AN/A211.10.115.1.2UnknownN/AN/A212.10.115.1.1UnknownN/AN/A
going through the article below looks like its not supported
[URL]
What are the options I have next ? Can I upgrade to LMS 3.3 or only do an upgrade for DFM ?
Want to avoid LMS 4 as that's an installation from scratch.
Cisco :: How To Retrieve Nexus 7010 Et 5596 Configuration Via Snmp
Mar 23, 2012I want to know how to retrieve the complete configuration for a Nexus via the snmpwalk or snmpget commands...
View 6 Replies View RelatedCisco WAN :: Setup Nexus (5596 Running NX-OS 5.1(3)N2(1)) To Use IP Ospf Name-lookup Command?
Aug 8, 2012I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies View Related