Cisco Switching/Routing :: IP Helper Command On Nexus 5K
Jan 1, 2012Are any of the following commands supported on Nexus 5K switches when deployed with L3 card:
ip helper addressip forward-protocolip directed-broadcast
ADVERTISEMENT
Cisco Switching/Routing :: How To Configure IP Helper In Nexus 7000
Jan 30, 2011I'm interested to know whether we can configure ip helper in nexus 7000?
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7K No Switchport Command Available?
Mar 22, 2013I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
Cisco Switching/Routing :: Debug Command Not Working On Nexus 5548?
Nov 15, 2012My Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor
SG01NX01# debug ip ospf 1 packets
SG01NX01# show debug
[Code].....
Cisco Switching/Routing :: Getting Nexus 5000 Command (default Interface X / X)
Jun 26, 2012when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies View RelatedCisco Switching/Routing :: Equivalent Command To Configure On Nexus 5596
Jun 21, 2012what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedCisco :: Missing IP Helper Address Command
Apr 6, 2012I have a stack of 3750's running IOS 12.2(25). "IP forward-protocal" command is configured, but the IP helper command is just not an option to put on an interface. Any have any idea of why that could be?
View 2 Replies View RelatedCisco Switching/Routing :: OSPF Subnet Admin Distance Command On Nexus 7K
Jun 20, 2012I am trying to modify the OSPF admin distance for a specific subnet under version 5.1(5) of the Nexus 7K, but this command does not appear to be available.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7000 SWACT Show Redundancy Command
Nov 9, 2012We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View RelatedCisco Switching/Routing :: Equivalent Command To Show Int Summary On The Nexus 7000?
Nov 20, 2011tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
Cisco Switching/Routing :: Nexus 7010 - Command For Restoring The Running Configuration
Apr 29, 2012What is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies View RelatedCisco Switches :: SF 200-48P / How To Add IP Address Helper Command To Switch
Feb 5, 2012I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. How to do this on the small business switch.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7010 IP Telnet Source-interface Command Not Working
Aug 20, 2012I have configured the ip telnet source-interface Loopback 0 command on a Nexus7010, but when I telnet to another device and do a show users, the ip address is of the closest interface to the device I telnet to, not the ip address of the Loopback. All interfaces are in vrf default. I am running 5.1(6) NXOS.
View 6 Replies View RelatedCisco Switching/Routing :: 1941W No IP From DHCP Server With Ip-helper
Jun 12, 2013I've a Cisco 1941W router which is DHCP server for data-VLANs and uses ip-helper for voice-VLANs. [code] I don't know why I can't have IP from wireless voice VLAN whereas it is OK and wired voice VLAN and conf is the same!
View 4 Replies View RelatedCisco Switching/Routing :: Does Ip Helper Address Work On A Layer 2 Switch 2950
Jan 9, 2012I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies View RelatedCisco Switching/Routing :: DHCP Request Not Being Forwarded By Helper Address Same VRF 6500?
Feb 22, 2013Version 12.2(33)SXI
int vlan 1
description client vlan
ip vrf forwarding A
ip address 10.1.1.1 255.255.255.0
standby 129 ip 10.1.1.2
standby 129 timers 1 4
standby 129 priority 105
standby 129 preempt
ip helper-address 10.1.2.20
[code]....
dhcp requests are not making it to the dhcp server SAME VRF (ip helper-addres is not doing anything.....)extended vrf traceroutes on udp 67 sourced from vlan2 are fine
I am expecting udp unicast packets on port 67 "giaddr" relay packets on the DHCP server generated and sourced by the relay on Vlan1
eg. Mar 1 01:59:06.731: DHCPD: setting giaddr to 10.1.1.1
This exact setup works in our preprod environment with the same code.Only difference is we run Distributed etherchannel on the 6500's where this doesnt work.
Wireshark on the client I can see the requests being sent Going to check it with debug ip dhcp server to check the relay logs out of production hours.
I have seen so many people say it IS and ISN'T supported on this version of the code.e.g. [URL]
I am aware the helper-adddress should inherit the vrf of the interface ip helper-address vrf command is not supported.The fact it works in the PP environment.... could this be due to the Distributed EtherChanel difference? or just some bug....
Cisco Switching/Routing :: 4500 / 3560 - DHCP Redundancy - IP Helper Address Point To HSRP?
Jan 5, 2012My actual Scenario
1 x 4500 and 1 x 3560?They are gateways of 8 Vlans?They are doing HSRP in each of those Vlans?The 4500 is the Active?There is a DHCP Pool for each of those Vlans on both gateways using "ip dhcp excluded-address" I ensured that the range of provided ips by each DHCP server will not be overlapped Obs.: Reducing the lease time, I ended with the calls bringing related problems.
OK, every thing is blue, every thing is fine.But the network diagram is realy complex(41 switchs, 89 uplinks), and depending of how is the network flow, one or other server answer first or latter.
For many reasons I would like that the secondary DHCP server would answer only if the primary DHCP server goes down.To me, the bigger reason is that DHCP database would be only in one DHCP server.But there is other reasons.
I passed by many frustrated solutions:Try to force a delay on the answer on one of the servers. - Impossible.Try to disable DHCP server, and, using EEM, enable it only if router became active in HSRP. - I couldn't do It.
What I'm thinking now is use the HSRP resource to resolve it.On both routers I would put a "ip helper-address" pointing to an Virtual_HSRP_IP.And depending on which router is the active, him will answer the request.
My first doubt is:Would it work?The second doubt is:Could I use the same Virtual_HSRP_IP that exists on that Vlan(see example 1),or I would need to point it to a Virtual_HSRP_IP in a different Vlan(see example 2)?
Example 1
-----------------------------------
| 4500 |
-----------------------------------
interface Vlan1
ip address 10.10.0.2 255.255.0.0
ip helper-address 10.10.0.1
standby 1 ip 10.10.0.1
[code]....
Cisco Switching/Routing :: Packet Discard On Nexus 5020 Link To Nexus 5K
Feb 23, 2011We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7000 With Fabric Extenders Nexus 2000?
Mar 15, 2013I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Cisco Switching/Routing :: Nexus FEX Transceivers SNMP MIB Nexus 5000
Dec 22, 2011Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View RelatedCisco Switching/Routing :: Datacenter Design With 2 Nexus 5K And 4 Nexus 2K?
Nov 13, 2012we are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies View RelatedCisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco Switching/Routing :: Catalyst 3560 - Routing Enabled With / Without Default Gateway Or IP Route Command
Feb 25, 2013We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
Cisco Switching/Routing :: 6500 MSFC No IP Routing Command
Jun 2, 2012I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
Cisco Switching/Routing :: 3750 / IP Routing Command Not Existent
Feb 27, 2013I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
Cisco WAN :: Hardware Command To Verify Nexus 5020
Apr 23, 2013What is the correct command to check the hardware of a Nexus 5020, like the show Inventori, show diag etc Used the same or is there a specific one for these items?
View 2 Replies View RelatedCisco Switching/Routing :: IP Routing Command In 6500?
Mar 16, 2013Where is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
Cisco WAN :: Setup Nexus (5596 Running NX-OS 5.1(3)N2(1)) To Use IP Ospf Name-lookup Command?
Aug 8, 2012I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 7010 / VSS - Does It Support Virtual Switching?
Apr 9, 2010Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedCisco Switching/Routing :: Facebook Forum Data Center Switching With Nexus 5000
Oct 8, 2012Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies View RelatedCisco Switching/Routing :: What Is The Command To Shutdown 1841
Oct 28, 2012What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies View RelatedCisco Switching/Routing :: Command QoS In VS-Sup2T Of 6509
Dec 10, 2012I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
Cisco Switching/Routing :: IP Flow Command On 3750-X?
Nov 12, 2012Trying to configure netflow on a 3750-X. I'm sort of copying my config from a router but, it seemd that the commandes below don't work.
Is there different set of commands to configure the source and destination.
ip flow-export source Tunnel0
ip flow-export destination 172.20.X.X 9995