Cisco Switching/Routing :: 7600 / ES20+ Configure Global Command Mls Qos
Dec 18, 2012
ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
View 2 Replies
ADVERTISEMENT
Feb 22, 2013
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies
View Related
Apr 23, 2012
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies
View Related
Mar 18, 2013
I have Cisco 7606 and wanted to test whether Cisco can drop frames due to invalid v lan ether type . i have configured the ports as
interface GigabitEthernet5/1
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet5/2
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
I have configured port also with encapsulation trunk dot1q ether type 88a8. i injected traffic with v lan ether type 0x8100. I expected to see drop traffic , however traffic passed in port to port.
View 1 Replies
View Related
Jun 13, 2013
Is it possible to configure MST on ASR and have rapid-pvst on 7600? can they interoperate? ASR sees no BPDUs and both are root bridges.
View 2 Replies
View Related
Jun 21, 2012
what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies
View Related
Apr 29, 2012
I have been working with the 871 router and configuring it for work at home users. Now we are purchasing and using the 881's instead. I noticed that after write erasing the router, I need to run the command in the global config "license boot module c880-data level advipservices" just have eigrp.However when I type show license, I get the following:
Index 1 Feature: advipservices
Period left: 8 weeks 3 days
Period Used: 2 hours 55 minutes
License Type: EvalRightToUse
[URL]
There is more but I left it out. However it shows that the advipservices license has only 8 weeks and 3 days left.What is this? I thought that when I buy a brand new router, I should get everything, including IOS licenses. So I would like to know is this a new licensing scheme and how does it get register and how do I get it so that the advipservices license is permanent?
View 4 Replies
View Related
Apr 3, 2012
I am facing problem about dot1ad global configuration command and my topology is here;
Notebook >> (access vlan 100) SW2960 (trunk)>> (trunk) C6500
First time I have create SVI interface on C6500 and enable trunk on interface that connected to SW2960 and SW2960 assigned access vlan 100 on port connected to Notebook. Then I tried to ping from Notebook to C6500 on SVI100 which work fine.
Second time I tried to enable MST on C6500 and after that everything still working and I can ping from Notebook to SVI100 on C6500.
Third time I tried on turn on dot1ad in global configuration mode and from now I can't ping from Notebook to C6500.
Forth time I tried to disable dot1ad from global configuration by "no dot1ad" command and then I can ping.
My intention is I would like to do EVC which require dot1ad in global configuration but I stuck in third step and don't know what's does it mean for this command and how I can resolve this issue?
Information on C6500
IOS Software (s2t54-ADVENTERPRISEK9-M), Version 15.0(1)SY1
Processor SUP-2T
Linecard WS-X6824-SFP
View 3 Replies
View Related
Oct 11, 2009
Unable to enter global QoS commands on the 4500E chassis? We're using 12.2(53)SG. If I go to 'conf t', there is no 'qos' command. In the configuration manuals I've seen for the 4500, the following commands seem to be supported:
qos
qos trust dscp
qos dbl
qos dbl exceed-action ecn
qos map dscp 0 to tx-queue 2
qos map dscp 8 10 12 14 to tx-queue 1
qos map dscp 16 18 20 22 to tx-queue 4
qos map dscp 24 26 28 30 to tx-queue 4
qos map dscp 34 36 38 to tx-queue 4
[Code] .....
View 3 Replies
View Related
Jan 5, 2012
I have a cisco 1841 and I am hooking up some cameras onto my network. My global IP is 64.190.170.2 and my internal IP which is going to my cameras DVR is 192.168.1.15. I need to be able to forward port 8080 from my global IP to my local IP so i can view my DVR remotely. What is the command i need to put in my Cisco 1841 to forward this port?
View 2 Replies
View Related
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Mar 6, 2012
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies
View Related
Apr 14, 2010
I have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
View 1 Replies
View Related
Nov 18, 2012
I want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
View 2 Replies
View Related
Apr 24, 2013
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies
View Related
Oct 9, 2011
i try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
View 18 Replies
View Related
Dec 22, 2011
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies
View Related
Jul 19, 2011
i have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes
!
! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx
!
version 15.2
service timestamps debug datetime msec
[Code]....
View 2 Replies
View Related
Jan 19, 2012
If I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?
View 1 Replies
View Related
Dec 6, 2012
i want to to ask about redirecting in MLS 7600 .assume the user a has an ip x.x.x.xand that user requested url...i want to to redirect his request to url...the users that have to pay the monthly bills , i want to give thim an ips and redirect all the http requests from this to a special local webpage .is is applicable to to it on router cisco 7600 ??or is it applicable on router 7206 npeg2 ? also i have siwtch 2960g.i dont want to do it by proxy server.
View 4 Replies
View Related
Sep 29, 2012
I am a soon to be network admin and have never set up a network to an existing network. Steps you need to add a new location to a company's network. For example if they are using 8 Building with 7600 Routers and 6500 and you need another building and they are using MPLS or Private Network, or Internet.
View 4 Replies
View Related
Sep 26, 2012
on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies
View Related
Apr 27, 2011
I have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
View 15 Replies
View Related
Nov 16, 2011
I am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
View 2 Replies
View Related
Jul 29, 2012
today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies
View Related
Jul 27, 2012
i have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
View 3 Replies
View Related
Apr 12, 2013
Actually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
View 2 Replies
View Related
Apr 29, 2012
I have run into a problem testing static route failovers using ECMP. I have an edge device (SUT) that has 2 NIC interfaces to an internal Loopback. Each NIC is a unique Gi port on an 7609 VLAN tagged with unique IP subnets. The 7600 is configured to route the loopback via the 2 NIC. I am using CEF in the network for other traffic performance testing. Using an external sniffer we can verify that when a ping is initiated externall to the SUT loopback a specific path is selected by the router.
Ping host ------Network-----7609 Gi1/21 (172.16.110.9)-----------SUT Nic1 (172.16.110.10)
| |
| -------Loopback 137.168.68.114/32
| |
7609 Gi2/21 (172.16.110.73)------------SUT Nic2 (172.16.110.74)
[code]....
Now, when the selected path is taken out of server (pulling cable for example), the 7609 is not clearing the routing table to indicate that particular path is down and failing over to the secondary path. Other things I have noticed is the show ip cef still shows both peers as well as the arp table but the interface shows down (show interface gi1/21 for example). I am running 15.1. My understanding is that since the ports are directly connected to the router, the ports should be detected as down and any association of the IP for the down port should removed. This should trigger the static route to update the static route for the end destination to use the second path and traffic should continue.
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)BOOTLDR: Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
View 4 Replies
View Related
Nov 27, 2012
how to know if my bgp neighbour advertised my network from his side or not ???
here is my config :
Gateway7600#sh ip bgp
BGP table version is 8, local router ID is 192.168.40.3
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
[code]....
View 5 Replies
View Related
May 23, 2013
we are using 7609 router. it forwarding traffic to wards my firewall which was not allowd in my router. when ever im checking for routes in router using show ip route x.x.x.x its showing SUBNET IS NOT IN TABLE, but in workmy firewall dropped connection i can able to see that networks.
View 2 Replies
View Related
Jan 21, 2013
I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies
View Related
Feb 5, 2012
I am pursuing a case of Cisco 7600 where the customer has asked me to highlight the major difference between teh new ES20 line cards and the SIP 400 cards
View 0 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related