Cisco Switching/Routing :: 4500 Unable To Enter Global QoS Commands
Oct 11, 2009
Unable to enter global QoS commands on the 4500E chassis? We're using 12.2(53)SG. If I go to 'conf t', there is no 'qos' command. In the configuration manuals I've seen for the 4500, the following commands seem to be supported:
qos
qos trust dscp
qos dbl
qos dbl exceed-action ecn
qos map dscp 0 to tx-queue 2
qos map dscp 8 10 12 14 to tx-queue 1
qos map dscp 16 18 20 22 to tx-queue 4
qos map dscp 24 26 28 30 to tx-queue 4
qos map dscp 34 36 38 to tx-queue 4
[Code] .....
View 3 Replies
ADVERTISEMENT
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Apr 22, 2012
I went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies
View Related
May 1, 2013
Interestingly enough I've seen about 3-4 posts with the exact same problem and yet not a single one is ever answered.. The task is simple:
"username USER password 5 SOMEPASS role network-admin"
It consistently outputs: "String failed to match token pattern at '^' marker." - always the carat is at the first character in whatever password I input. I've ensured passwords I input meet the conditions of "password strength-check" and I have also disabled this feature and repeated with numerous passwords to no effect.
View 7 Replies
View Related
Apr 3, 2012
I am facing problem about dot1ad global configuration command and my topology is here;
Notebook >> (access vlan 100) SW2960 (trunk)>> (trunk) C6500
First time I have create SVI interface on C6500 and enable trunk on interface that connected to SW2960 and SW2960 assigned access vlan 100 on port connected to Notebook. Then I tried to ping from Notebook to C6500 on SVI100 which work fine.
Second time I tried to enable MST on C6500 and after that everything still working and I can ping from Notebook to SVI100 on C6500.
Third time I tried on turn on dot1ad in global configuration mode and from now I can't ping from Notebook to C6500.
Forth time I tried to disable dot1ad from global configuration by "no dot1ad" command and then I can ping.
My intention is I would like to do EVC which require dot1ad in global configuration but I stuck in third step and don't know what's does it mean for this command and how I can resolve this issue?
Information on C6500
IOS Software (s2t54-ADVENTERPRISEK9-M), Version 15.0(1)SY1
Processor SUP-2T
Linecard WS-X6824-SFP
View 3 Replies
View Related
Dec 18, 2012
ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
View 2 Replies
View Related
Dec 12, 2012
I tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies
View Related
Jan 5, 2012
I have a cisco 1841 and I am hooking up some cameras onto my network. My global IP is 64.190.170.2 and my internal IP which is going to my cameras DVR is 192.168.1.15. I need to be able to forward port 8080 from my global IP to my local IP so i can view my DVR remotely. What is the command i need to put in my Cisco 1841 to forward this port?
View 2 Replies
View Related
Mar 7, 2013
I have a catalyst 3550 and will be using it to run my cisco 7940 and 7960 ip phones with POE. When I plug the phones into the switch they power up just fine but the phones will not dial out as they have little x's by the line. I have also tried going through the set up of the 3550 but get stuck in one place. When I go to the 10.0.0.0, the screen will not allow me to enter the telnet page or allow me to enter any information. In the manual it shows a pic of what the screen should look like when I go to 10.0.0.1, but I am getting an entirely different page.
What I need to do to get everything set up correctly?
View 5 Replies
View Related
Jan 31, 2013
We are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
View 1 Replies
View Related
Feb 8, 2012
I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies
View Related
Jul 30, 2012
SSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
View 2 Replies
View Related
Feb 22, 2013
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies
View Related
Apr 23, 2012
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies
View Related
Oct 11, 2012
I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies
View Related
Oct 6, 2012
We have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 Replies
View Related
Nov 13, 2011
I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
View 1 Replies
View Related
Feb 15, 2012
configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
View 9 Replies
View Related
Jun 7, 2012
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 2 Replies
View Related
Oct 30, 2011
I have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies
View Related
Mar 8, 2013
I have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
View 5 Replies
View Related
Jan 22, 2013
We are upgrading from 3550 - 3560 switches.On the 3550's we have this on each interface: [code] The 3550's wont accept the wrr-queue commands. How to set these on the 3560's.
View 1 Replies
View Related
Aug 20, 2012
I am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.
View 4 Replies
View Related
Jan 27, 2013
I am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.
View 6 Replies
View Related
Oct 25, 2012
Recently we have configured new site where we are unable to ping global DNS from routers and switches.Checked in the firewall ICMP is allowed.The thing we did is we made Native vlan as vlan 10 (Data vlan ) instead of vlan1. Do this is the issue for not pinging.
View 6 Replies
View Related
May 2, 2011
Not able to enter 10.12 series address in LAN PC
View 12 Replies
View Related
Sep 15, 2012
What are recommended commands to get input for network documentation (for disaster recovery)?
I've got 6500 with these modules: WS-SVC-FWM-1,
WS-SVC-IDSM-2, VS-S720-10G, WS-X6704-10GE, WS-X6748-SFP and dozens of WS-C3750E-48TD in couple of buildings.
So far I have these commands: Code...
View 3 Replies
View Related
Sep 8, 2012
I want to give limited access to our first level support so that they can execute certain basic commands like, port vlan change, access port shut/no-shut on Cisco 6509 and 3750E switches IOS based. I want to restrict them to only few options so they can not make changes to uplink (TenGig) ports and can not issue reload command etc. We do not have TACACS. What is the best way to achieve this?
View 2 Replies
View Related
Sep 22, 2010
Working with wired Cisco equipment for many years, but trying to configure an integrated wireless AP for the first time.
I have a Cisco 891w router with the following software (main and integrated AP801 wireless AP):
1. Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 12.4(22)YB
License Level: advipservices
2. Cisco IOS Software, AP801 Software (AP801-RCVK9W8-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Opening a connection to integrated AP801 wireless device for performing wireless configuration tasks, the connection is established OK, authentication is passed OK using credentials from main configuration file, gaining level 15 privileges with enable command, but after that... no way to enter "Global Configuration mode" because there are no "configure" family commands present!!! Simply can't say "Conf t" because there is no such command!
View 9 Replies
View Related
Mar 6, 2012
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies
View Related
Dec 18, 2011
I was reading my book when I found :
redistribute ospf 2 external 2
The book says only ospf external routes of type 2 will be redistributed.But when I tried to configure the above command on router, I was not able to configure it; there was no external or internal option available with redistribute ospf command.
Below is the output:
R2(config)#router rip
R2(config-router)#redistribute ospf 1 ?
match Redistribution of OSPF routes
metric Metric for redistributed routes
route-map Route map reference
vrf VPN Routing/Forwarding Instance
<cr>
R2# show version
Cisco IOS Software, 2600 Software (C2691-ADVIPSERVICESK9-M), Version 12.4(15)T6, RELEASE SOFTWARE (fc2)
Do we have such command for eigrp? For example If i want to redistribute only external routes from eigrp into ospf, do we have any command such as :redistribute eigrp 1 external ?I understand there is several ways to achieve to same goal however I am just curious if we could acheive the same goal using single redistribute eigrp command without any route-map.
View 1 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
View 2 Replies
View Related
Apr 10, 2012
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
View 1 Replies
View Related
