SSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
View 2 RepliesI have a Catalyst 4500 L3 Switch Software (cat4500e UNIVERSAL-M), Version 03.02.00.XO RELEASE SOFTWARE (fc2). So I just wanted to verify that the switch only does dot1q encapsulation because the switchport trunk encapsulation dot1q command does not work.
View 3 Replies View RelatedWe are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies View RelatedWe are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies View RelatedI am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View RelatedWe have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 2 Replies View RelatedI have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View RelatedI have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
We are upgrading from 3550 - 3560 switches.On the 3550's we have this on each interface: [code] The 3550's wont accept the wrr-queue commands. How to set these on the 3560's.
View 1 Replies View RelatedI am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.
View 4 Replies View RelatedI am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.
View 6 Replies View RelatedWhat are recommended commands to get input for network documentation (for disaster recovery)?
I've got 6500 with these modules: WS-SVC-FWM-1,
WS-SVC-IDSM-2, VS-S720-10G, WS-X6704-10GE, WS-X6748-SFP and dozens of WS-C3750E-48TD in couple of buildings.
So far I have these commands: Code...
I want to give limited access to our first level support so that they can execute certain basic commands like, port vlan change, access port shut/no-shut on Cisco 6509 and 3750E switches IOS based. I want to restrict them to only few options so they can not make changes to uplink (TenGig) ports and can not issue reload command etc. We do not have TACACS. What is the best way to achieve this?
View 2 Replies View RelatedUnable to enter global QoS commands on the 4500E chassis? We're using 12.2(53)SG. If I go to 'conf t', there is no 'qos' command. In the configuration manuals I've seen for the 4500, the following commands seem to be supported:
qos
qos trust dscp
qos dbl
qos dbl exceed-action ecn
qos map dscp 0 to tx-queue 2
qos map dscp 8 10 12 14 to tx-queue 1
qos map dscp 16 18 20 22 to tx-queue 4
qos map dscp 24 26 28 30 to tx-queue 4
qos map dscp 34 36 38 to tx-queue 4
[Code] .....
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies View RelatedI went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies View RelatedI was reading my book when I found :
redistribute ospf 2 external 2
The book says only ospf external routes of type 2 will be redistributed.But when I tried to configure the above command on router, I was not able to configure it; there was no external or internal option available with redistribute ospf command.
Below is the output:
R2(config)#router rip
R2(config-router)#redistribute ospf 1 ?
match Redistribution of OSPF routes
metric Metric for redistributed routes
route-map Route map reference
vrf VPN Routing/Forwarding Instance
<cr>
R2# show version
Cisco IOS Software, 2600 Software (C2691-ADVIPSERVICESK9-M), Version 12.4(15)T6, RELEASE SOFTWARE (fc2)
Do we have such command for eigrp? For example If i want to redistribute only external routes from eigrp into ospf, do we have any command such as :redistribute eigrp 1 external ?I understand there is several ways to achieve to same goal however I am just curious if we could acheive the same goal using single redistribute eigrp command without any route-map.
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
I'm trying to configure LLDP-MED between a Cat45010+E Sup7 (IOS 15.1) and Polycom CX600 Lync phones. I have created and applied the correct network policy for the interfaces.
From these sites, I need to send all the correct TLVs or the phones won't respond: {URL}.
When a scour the config of the switch, I can't find any related configuration commands relating to the specific LLDP-MED TLV components which are enabled/disabled. Where are they hiding? I would like to confirm which TLVs are being sent by my switch and if they are matched to the phone. I can always use the DHCP method, put this is not preferred.
We just replaced a floor swithc, and ended up going with an IOS-XE software, LMS does not seem to like this software, the device is not available in my Identity dashboard, it's abviously running dot1x.
LMS shows it as software version 03.02.01.SG, same as you get when you do a show version, license level is enterprise services.
Actual Image name: cat4500e-universalk9.SPA.03.02.01.SG.150-2.SG1.bin
Also, the IOS upgrade option does not work for this device, it give an error saying to perform an inventory collection, which I have manually performed, the device is reachable and manageable by LMS, and it does not show up in any of the IOS version reports.
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI have a Cisco LMS 4.2.1 on a Windows 2008 Server R2 platform and I would like to backup the configuration of my WS-C4503-E version cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1I create the job in Configuration > Configuration Archive > Synchronization and after the execution of the job, I check th status in Admin > Job > Browser: I don't know why the archive doesn't exist. It's a newly install.
View 2 Replies View Relatedi want to activate flexible netflow on my WS-X45-SUP7-E with IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG. I've started with a simple configuration like this:
Configuring a Flow Monitor for IPv4/IPv6 Traffic Using the Flexible NetFlow
“NetFlow IPv4 Original Input” Predefined Record
SUMMARY STEPS
how ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
In studying and testing SSL VPN on an ASA I have the network as shown in the attached diagram. The configuration is based on an ASA with 8.3 but our ASA is 8.2 and at this time I'm not familiar with the new NAT configuration and commands in 8.3 or later and how to translate the 'nat (inside,outside) source static' for me to an 8.2 version.
View 3 Replies View RelatedI try to get a ASA with the new software 8.4.2 running. On an old pix we had the nat command: static (inside,outside) tcp interface www 192.168.15.252 www netmask 255.255.255.255 0 0,In all the new documents about 8.4.2 I can find that it should work with something like:
object network web_host nat (inside,outside) static interface service tcp www www
I want to forward http traffic from the outside interface to this host. In the log I just get entries about blocking ACL - but both is allowed on the outside access-list - traffic to the inside IP and also to the outside interface IP.
I also tried it with "Public Server" - but when I try to use the Interface address I just get the message: Address x.x.x.x overlaps with outside interface address.
Is it still possible to do port forwarding on the outside interface?
I have two nic one connected with DSL modem with gateway 192.168.1.1 for Internet. another nic connected with office Intranet with gateway 10.226.122.x . I can connect only one network at a time disabling other.. I know route add command can be used for linking the both network so I can simultaneously use Internet and Intranet..can you elaborate with example (five years ago I set up the same with route add command.. now my memory failing..)
View 1 Replies View RelatedAny link to the commands in the Roman asa 55xx ? Did not find on Cisco's documents.
My small ASA 5505 crashed and comes up in Roman. Like to try get SW and Config back if possible.
I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View Related