Cisco Switching/Routing :: Sge2000 - Cannot Console Mode To Get Prompt To Type Commands
Mar 6, 2012I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: To Get Into Switch Prompt Without Mode Button 2955
Nov 3, 2012I have found that the Catalyst 2955 series switches do not use an external MODE button for getting a switch into the switch: prompt, but they use a break sequence like routers do to get into Rommon state URL
So I was wondering if there is a similar mecanism that applies to other kind of Catalyst switches, like 2960, 3560 or 3750.
Cisco Switching/Routing :: Can Sge2000 Stack With Linksys Sge2000
Aug 22, 2011I'm having trouble getting a stack of three sge2000 switches to connect together and NOT reboot.Two of the switches are older Linksys sge2000s and they stack well together, but as soon as i connect the new Cisco sge2000, it will make them both reboot sequentially, even though it detects that it needs to be #3 in the stack.SW 1 port 24 is connected to SW 2 port 12 and they function correctly (both of the linksys switches). The documentation states they should be connected in a ring topology so I first tried completing the loop with SW3 (the newer cisco sge2000). When that had the aforementioned troubles I just connected SW2 port 24 to SW3 port 12. Still forcing the switches to reboot.I SUSPECT it may be a firmware/software issue, but I wanted to check if they'ed even work together.
View 2 Replies View RelatedCisco Switching/Routing :: C2950-24 / Unable To Take Control In Console Mode
Jan 25, 2012I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
Cisco Switching/Routing :: C4507R+E - How To Disable Radius Messages In Console Mode
Jan 14, 2012I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies View RelatedCisco Switching/Routing :: 2691 - Unable To Reach Enable Mode By Console Connection
May 10, 2012I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
Cisco :: Can't Get A Console Prompt
Sep 7, 2012Almost new switch giving error: %%Low on memory Try again later.This is a 2960 48pt lanbase image.I can't get a console prompt, telnet in or anything, it is however switching packets OK. [code]
View 1 Replies View RelatedCisco Firewall :: 5505 Cannot Type In Commands In Putty Or Hyper-terminal
May 5, 2013I have a Cisco ASA 5505. This has been previously configured. I am trying to give it a factory reset and I am being able to connect via Putty and Hyper-terminal but I cannot enter anything. I am able to go into ROMMAN mode by using the esc key.
View 6 Replies View RelatedCisco WAN :: SGE2000-G5 VLAN Routing And Switching
May 15, 2012Im planning for a network upgrade.77.110.87.112/28 - is assigned to selected users and configured manually.(note: they are public IP which our ISP assigned)192.168.1.0/24 - is assigned to users that are not allowed to use internet services and configured manually. I have CISCO 1841 Router connected to the internet and CISCO SGE2000-G5 24ports layer 3 switch that is connected to cisco 1841 router.i want to create vlan in layer 3 switch. [code] i want all vlans would still ping to each other and file/printer sharing is available.kindly check if my network upgrade plan is correct, how am i going to configure those vlan in my layer 3 switch and to connect to the internet.
View 12 Replies View RelatedCisco Switching/Routing :: SGE2000 Switch Without CLI?
Sep 11, 2012I have recently purchased a a Cisco SGE2000 switch and when connected to it via console cable, I was introduced to "Switch main menu" which was kind of a GUI interface. I found a way of accessing what is called a lightweight CLI (lcli).After having a few searches on google it turns out that this switch doesn't have a proper CLI. Is this possible at all? I thought that all managed switches have CLI?
View 2 Replies View RelatedCisco Switching/Routing :: SGE2000 Switches To Dell - STP Loop
Nov 24, 2012We have a couple of cisco SGE switches connected to a single DELL, between the cisco switches we have a trunk interface. I'm not sure which setting should be configured on the switches to get it working because a loop is occuring.
View 1 Replies View RelatedCisco Switching/Routing :: SGE2000 Login After Password Change?
May 8, 2013I have recently aquired a Cisco SGE2000 switch and the first thing I did was update to the latest firmware and change password. Now I cant login? Neither my admin / admin dosent work nor the new user I have created. Is there any characters that this dosesnt support like backslashes or forward slashes for password? If not then what can I do to get access to the switch again?
View 2 Replies View RelatedCisco Switching/Routing :: Can LLDP Be Disabled On SGE2000 Switch
May 2, 2013I just want the switch to be quiet so that I can perform some network testing with only the connected hosts showing up in my traffic analysis program. But every 30 seconds or so the switch sends out an LLDP packet. This switch is only used in the lab for running tests so I know I don't need the LLDP feature running.
This article explains how to disable LLDP globally on a Catalyst switch, but I can't find any option to disable LLDP in the SGE2000's configuration menus.
Cisco Switching/Routing :: IP Discovery Utility For SGE2000 24-port Switch?
Nov 20, 2011I was handed two SGE2000 24-port 10/100/1000 switches. The default IP address does not work on either of them. Short of doing a hardware reset, is there an IP discovery utility that I can run.how I can find the IP?
View 5 Replies View RelatedCisco Switching/Routing :: 891-W Access Verification Prompt?
Jan 25, 2013Recieved this unit from an individual who has very little knowledge (like myself) with the 800 series.
I'm having issues just getting into this device, when I power it on and console into the unit i am presented with an "Access Verification" prompt that requires credentials that I do not have/know.
At some point (not sure how) I managed to get to a "yourname#" prompt at which point I configured using this document here and created a username and password and some other basic settings, I saved the config and did a reload and it takes me right back to that "Access Verification" prompt.
Sould I be using the CCPE to gain access to this device instead? Is there a way to recover that "Access Verification" username and pass? How did I ever get to that "yourname#" prompt?
Cisco Switching/Routing :: 3750 Prompt For Password Change
Feb 6, 2013I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
Cisco Switching/Routing :: 4500X IOS XE Commands
Jan 31, 2013We are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
Cisco Switching/Routing :: 7206vxr 12.2 - No MLS QoS Commands
Feb 8, 2012I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies View RelatedCisco Switching/Routing :: SSH Commands Not Available In IOS CAT4500e
Jul 30, 2012SSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
View 2 Replies View RelatedCisco Switching/Routing :: 2950 - Enabled AAA New-model / Telnet Prompt Username Needed?
Nov 17, 2012I was testing on 802.1x function on Catalyst 2950. the funtion itself work fine with my radius. but after I have setup the aaa new-model, I have no access to my switch!everytime I telnet it prompt me username, but I didn't create any user!!
how to recover to the origianl status, just prompt to input password but not username needed, and with 802.1x enable ofcause. [code]
Cisco Switching/Routing :: Logging Commands On 6500
Oct 11, 2012I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View RelatedCisco Switching/Routing :: SSH Commands Not Available In 4500x Switch?
Oct 6, 2012We have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 Replies View RelatedCisco Switching/Routing :: 2911 IP SLA Commands Missing?
Nov 13, 2011I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
Cisco Switching/Routing :: Nexus 5010 Won't Load System Image - Stuck At Boot Prompt
Sep 29, 2012I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
Cisco Switching/Routing :: ASA5520 - Commands To Apply NAT On Interface?
Feb 15, 2012configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
Cisco Switching/Routing :: 3850 Cannot Configure HSRP Cause The Commands Are Not There
Jun 7, 2012I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 2 Replies View RelatedCisco Switching/Routing :: 3750E NetFlow Commands Available On Switch
Oct 30, 2011I have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View RelatedCisco Switching/Routing :: 2811 / IOS Firewall Commands Not Working?
Mar 8, 2013I have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
Cisco Switching/Routing :: 3550 Won't Accept WRR-Queue Commands
Jan 22, 2013We are upgrading from 3550 - 3560 switches.On the 3550's we have this on each interface: [code] The 3550's wont accept the wrr-queue commands. How to set these on the 3560's.
View 1 Replies View RelatedCisco Switching/Routing :: No 802.1x Interface Commands On 3560 Switch
Aug 20, 2012I am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.
View 4 Replies View RelatedCisco Switching/Routing :: No Power Inline Commands On 1921?
Jan 27, 2013I am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.
View 6 Replies View RelatedCisco Switching/Routing :: 6500 - Commands To Get Input For Network Documentation?
Sep 15, 2012What are recommended commands to get input for network documentation (for disaster recovery)?
I've got 6500 with these modules: WS-SVC-FWM-1,
WS-SVC-IDSM-2, VS-S720-10G, WS-X6704-10GE, WS-X6748-SFP and dozens of WS-C3750E-48TD in couple of buildings.
So far I have these commands: Code...
Cisco Switching/Routing :: 6509 User / Role Based Commands
Sep 8, 2012I want to give limited access to our first level support so that they can execute certain basic commands like, port vlan change, access port shut/no-shut on Cisco 6509 and 3750E switches IOS based. I want to restrict them to only few options so they can not make changes to uplink (TenGig) ports and can not issue reload command etc. We do not have TACACS. What is the best way to achieve this?
View 2 Replies View Related
