Cisco Switching/Routing :: SSH Commands Not Available In 4500x Switch?
Oct 6, 2012We have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 RepliesWe have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 RepliesWe are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
I have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View RelatedI am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.
View 4 Replies View RelatedCan I have three 4500X in VSS? or is the limit two? Do I need a different license or a specific IOS?
View 1 Replies View Relatedwhen the VSS will be supported on Catalyst Supervisor Engine 7-E or 7-LE and on Catalyst 4500-X?And does VSS will require Enterprise license ? or the IP base will be enaugh?
View 7 Replies View RelatedAre there any plans to allow DWDM SFP+ on new 4500x ? If so, how soon?
View 2 Replies View RelatedAs defined in datasheet, 4500x switch supports 10 GE. Can i use twin gig converter to convert some ports to 1 GE ?
View 1 Replies View RelatedDoes the new 4500X series will support a per port MTU?
View 2 Replies View RelatedHow to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies View Relatedim currenly configuring a 4500X with 16 port. All sfp are 1Gig, but when I input show ip int brief, it shows that the interfaces are on 10 Gig. Does Catalyst 4500X already support the 1Gig SFP without inputting a command or do I have to configure it to activate the 1Gig interface?
View 6 Replies View RelatedAre all ports on Catalyst 4500X Gigabit/10-Gigabit or just the ports on 8-port module. We are looking at 4500X for campus distribution layer but need Gig ports to access switches for now and may year from now will be using 10G.
View 7 Replies View RelatedI'm trying to figure out how to (or if I can) setup the management interfaces (fa1) on a couple of new 4500X switches. My issue is that the 4500X's themselves are the gateway for my management VLAN (.1 HSRP virtual, .2 and .3 SVIs on the pair of switches).
I would like to assign addresses from the management VLAN to the router Fa1 management interfaces but the software configuration guide seems to note this is not supported (and indeed it doesn't seem to work).
Physically I have Fa1 from core-1 into a port on an adjacent switch. Fa1 from core-2 also goes into a port on that adjacent switch. Both are in my management VLAN, whose SVIs are on the cores themselves.
I am interesting if 3560x supports ePAgP. I have VSS which is formed by two 4500x switches. Can I use 3560x, which is connected two both VSS members via 10Gb optics for Dual Active detection ?
View 2 Replies View RelatedI have probem with symmetric load balancig, in case when both ends of ether channel are on the sam switch (we are using VLAN translation).We need to create L2 port channel with both ends on same switch (Cisco WS-C4500X-24X-ES), for example:Po1 – Gi0/1, Gi0/3 (one end of port channel )Po2 – Gi0/2, Gi0/4 (other end of port channel)On ports in Po2 we will configure VLAN mapping.My question is what is the best ether-channel load-balancing scheme with wich we can accomplish full symmetry in both directions? For example, if traffic in one direction goes through Gi0/1 (member of Po1), in other direction also must go through Gi0/1. This is required because we need to connect four appliances for DPI (they are full L2 transparent) and traffic through each appliance need to be symmetric.
I can set-up src-ip, dst-ip, src-dst-ip etc. load balancing, but, actually I need src-ip on Po1 and dst-ip on Po2. Is there any way to set up different load balancing mechanism for different ether channel on same switch (4500X).
When will the WS-4500X-32 support the TrustSec MACsec Encryption ?
View 1 Replies View RelatedWe have some ASR WAN routers which have a dedicated 400M interface to a remote site.
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M.
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.
I am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies View RelatedSSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
View 2 Replies View RelatedI am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 2 Replies View RelatedI have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
We are upgrading from 3550 - 3560 switches.On the 3550's we have this on each interface: [code] The 3550's wont accept the wrr-queue commands. How to set these on the 3560's.
View 1 Replies View RelatedI am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.
View 6 Replies View RelatedWhat are recommended commands to get input for network documentation (for disaster recovery)?
I've got 6500 with these modules: WS-SVC-FWM-1,
WS-SVC-IDSM-2, VS-S720-10G, WS-X6704-10GE, WS-X6748-SFP and dozens of WS-C3750E-48TD in couple of buildings.
So far I have these commands: Code...
I want to give limited access to our first level support so that they can execute certain basic commands like, port vlan change, access port shut/no-shut on Cisco 6509 and 3750E switches IOS based. I want to restrict them to only few options so they can not make changes to uplink (TenGig) ports and can not issue reload command etc. We do not have TACACS. What is the best way to achieve this?
View 2 Replies View RelatedUnable to enter global QoS commands on the 4500E chassis? We're using 12.2(53)SG. If I go to 'conf t', there is no 'qos' command. In the configuration manuals I've seen for the 4500, the following commands seem to be supported:
qos
qos trust dscp
qos dbl
qos dbl exceed-action ecn
qos map dscp 0 to tx-queue 2
qos map dscp 8 10 12 14 to tx-queue 1
qos map dscp 16 18 20 22 to tx-queue 4
qos map dscp 24 26 28 30 to tx-queue 4
qos map dscp 34 36 38 to tx-queue 4
[Code] .....
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies View RelatedI went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies View RelatedI was reading my book when I found :
redistribute ospf 2 external 2
The book says only ospf external routes of type 2 will be redistributed.But when I tried to configure the above command on router, I was not able to configure it; there was no external or internal option available with redistribute ospf command.
Below is the output:
R2(config)#router rip
R2(config-router)#redistribute ospf 1 ?
match Redistribution of OSPF routes
metric Metric for redistributed routes
route-map Route map reference
vrf VPN Routing/Forwarding Instance
<cr>
R2# show version
Cisco IOS Software, 2600 Software (C2691-ADVIPSERVICESK9-M), Version 12.4(15)T6, RELEASE SOFTWARE (fc2)
Do we have such command for eigrp? For example If i want to redistribute only external routes from eigrp into ospf, do we have any command such as :redistribute eigrp 1 external ?I understand there is several ways to achieve to same goal however I am just curious if we could acheive the same goal using single redistribute eigrp command without any route-map.