when the VSS will be supported on Catalyst Supervisor Engine 7-E or 7-LE and on Catalyst 4500-X?And does VSS will require Enterprise license ? or the IP base will be enaugh?
View 7 RepliesDoes the new 4500X series will support a per port MTU?
View 2 Replies View RelatedWhen will the WS-4500X-32 support the TrustSec MACsec Encryption ?
View 1 Replies View RelatedCan I have three 4500X in VSS? or is the limit two? Do I need a different license or a specific IOS?
View 1 Replies View RelatedWe are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out
2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available.
3. when I entered username etc. I got a message " CLI deprecated soon".
Are there any plans to allow DWDM SFP+ on new 4500x ? If so, how soon?
View 2 Replies View RelatedWe have a 4500x Switch in this ssh commands are not available.its running on (cat4500e- UNIVERSAL-M), Version 03.03.00.SG) IOS XE.
View 2 Replies View RelatedAs defined in datasheet, 4500x switch supports 10 GE. Can i use twin gig converter to convert some ports to 1 GE ?
View 1 Replies View RelatedHow to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies View Relatedim currenly configuring a 4500X with 16 port. All sfp are 1Gig, but when I input show ip int brief, it shows that the interfaces are on 10 Gig. Does Catalyst 4500X already support the 1Gig SFP without inputting a command or do I have to configure it to activate the 1Gig interface?
View 6 Replies View RelatedAre all ports on Catalyst 4500X Gigabit/10-Gigabit or just the ports on 8-port module. We are looking at 4500X for campus distribution layer but need Gig ports to access switches for now and may year from now will be using 10G.
View 7 Replies View RelatedI'm trying to figure out how to (or if I can) setup the management interfaces (fa1) on a couple of new 4500X switches. My issue is that the 4500X's themselves are the gateway for my management VLAN (.1 HSRP virtual, .2 and .3 SVIs on the pair of switches).
I would like to assign addresses from the management VLAN to the router Fa1 management interfaces but the software configuration guide seems to note this is not supported (and indeed it doesn't seem to work).
Physically I have Fa1 from core-1 into a port on an adjacent switch. Fa1 from core-2 also goes into a port on that adjacent switch. Both are in my management VLAN, whose SVIs are on the cores themselves.
I am interesting if 3560x supports ePAgP. I have VSS which is formed by two 4500x switches. Can I use 3560x, which is connected two both VSS members via 10Gb optics for Dual Active detection ?
View 2 Replies View RelatedI have probem with symmetric load balancig, in case when both ends of ether channel are on the sam switch (we are using VLAN translation).We need to create L2 port channel with both ends on same switch (Cisco WS-C4500X-24X-ES), for example:Po1 – Gi0/1, Gi0/3 (one end of port channel )Po2 – Gi0/2, Gi0/4 (other end of port channel)On ports in Po2 we will configure VLAN mapping.My question is what is the best ether-channel load-balancing scheme with wich we can accomplish full symmetry in both directions? For example, if traffic in one direction goes through Gi0/1 (member of Po1), in other direction also must go through Gi0/1. This is required because we need to connect four appliances for DPI (they are full L2 transparent) and traffic through each appliance need to be symmetric.
I can set-up src-ip, dst-ip, src-dst-ip etc. load balancing, but, actually I need src-ip on Po1 and dst-ip on Po2. Is there any way to set up different load balancing mechanism for different ether channel on same switch (4500X).
We have some ASR WAN routers which have a dedicated 400M interface to a remote site.
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M.
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.
I am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedCan nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedDoes the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedCoincidentally when i tried to configure router 877 as an adsl router i found that a vlan configuration is included. my question is what is the benefit of using vlans in router ??? i studied that we use it in switches for the purpose of network enhancment from broadcasts and netwrok segmentation. why we use vlans in routers ?
View 9 Replies View RelatedDoes the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies View RelatedDoes this Router Support SIP Forwarding?
View 1 Replies View Related I have a 3560G switch with c3560-advipservicesk9-mz.122-46.SE and 2 routers. The switch has vlans defined. I want to route all traffic on vlan 25 out of one of the routers exclusively. Here is what I have attempted:
-Set the SDM template to routing & reload
-Define an access-list for the v lan traffic
-Define the route-map
-Apply the route-map to the vlan interface
When I attempt the last step I receive the following syslog error:
%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map RM_IMDGuest not supported for Policy-Based Routing
Also, the route-map is removed from the vlan interface after this error is thrown. Im 99% confident that PBR is supported on this switch (am I wrong?). Here is the relevant show output:...
access-list 125 permit ip 192.168.25.0 0.0.0.255 any
route-map RM_IMDGuest permit 10
match ip address 125
set ip next-hop 192.168.5.3
[code]....
We purchased ME 3400 switch and trying to implement it. But its quite surprising in the ME3400 configuration guide that the switch does not support VTP. When I checked in Feature navigator under feature "VTP" i could see ME3400 supports VTP. But when i get into CLI of ME3400, i am not getting any option of configuring VTP. I could see in some sites VMPS is supported in ME3400.
I would like to confirm the following:
1. Does VTP support present in ME3400 or not? If not, what would be the reason that it is not included in ME3400.
2. If not what is the alternative.
Network is already running VTP of around 30 switches.
Its required that all ports on nexus 7k should be user configurable as either 1G/10G/FcoE. Which module do i need in this case ?
View 0 Replies View RelatedDoes the Catalyst 3560 support GRE ?
I know that Catalyst 3750X support GRE ,but Catalyst 3750X cannot work in hardware it.
Does the Catalyst 3560 cannot work in hardware too?
Does Cisco SG200-50 50 port gigabit smart switch have support for SNMP ? I have updated the firmware and still can not find any option for snmp.Sent from Cisco Technical Support iPad App.
View 3 Replies View RelatedI would like to ask you that switch WS-C3750x-24S-S can support with GLBP?i have IOS version : S375xvk9t-12258SE.
View 2 Replies View RelatedIf i look at the Feature Navigator , it says that IP Base Supports OSPF and EIGRP. But if i look at the Cisco Link it contradicts the Cisco Feature Navigator.
[URL]
if I have 6509-E with VSS-SUP720-10G and want to run OSPF and BGP on the Switch. What is the IOS i require? WIll IP Base Suffice or i need to take Advance or Enterprise Image.
We will deploy several 4507 with 2xsup7 as a L2 access switches for our office.Does LAN_Base IOS version support SSO or we need purchase IP_Base IOS (L3)?
View 1 Replies View RelatedIf the 3560 or 3750 "X" series support GRE.I am pretty certain the older 3750-E does not support GRE (both in hardware and software)Was hoping the new super duper X series do. If not, it could get expensive
View 5 Replies View Relatedi have some ME-3600x. some of version 12.2 and one of version 15.5. te last one hast same config as all other. but if i check for rstp it sends.i know abount global config commands:
-spanning-tree mode rapid-pvst
-spanning-tree extend system-id
but there is no spanning-tree support. this causes many more problems. so it is important to solve spanning tee at first.is it possible without downgrading this device?