Cisco Switching/Routing :: SG200-50 - Does It Have Support For SNMP?
Jul 4, 2012
Does Cisco SG200-50 50 port gigabit smart switch have support for SNMP ? I have updated the firmware and still can not find any option for snmp.Sent from Cisco Technical Support iPad App.
View 3 Replies
ADVERTISEMENT
Jan 7, 2013
Iam having some issue trying to configure snmp-server context vrf XXX.From some reason even if i put my VRF name i cant see anything about this vrfthis is the command i add:
snmp-server context def vrf datacenter
View 3 Replies
View Related
Apr 15, 2013
does SG200 support VLAN Trunking?
View 1 Replies
View Related
Jul 17, 2012
I currently work in the IT field part-time as a end-user support technician while I am finishing my Bachelor's Degree in Network Administration. I'm not completely new to networking at this point, but I am by no means a master of it either. The basics of small networks (less than 10 PCs) and the lower-end of small business grade Cisco equipment are not unfamiliar to me. Up until this point however, I have had very little experience with any higher-end Cisco networking equipment.
Now on to the questions, which may seem like the answers should be obvious, but let's face it, I do not have the resources to own much equipment myself at this time for experimentation purposes, nor does the school I am attending have a lot of financial resources to provide us with recent hardware to learn on. What I want to know are a few things about PoE as implemented on Cisco devices, specifically the SG200-50P small business series switch. According to the technical documentation, the switch supports PoE on 24 of its 48 ports, specifically 1 - 12 and 24 - 36; simple enough. The switch is currently installed in an office that has less than 24 connected devices, but that is currently expanding. None of the PoE ports are utilized as of yet, but going forward, there will be more than 24 connected devices. Will another switch need to be installed if the additional connected devices (PCs and printers) are not using PoE, or is the PoE an auto-sensing feature that will simply remain disabled if a device that does not require power over the network cable is connected? Is there some setting that needs to be changed through the management interface to keep devices that should not be drawing power from doing so?
There will likely be some additional questions generated by my inquiry, and I fully understand if these are completely novice questions, but I admittedly do not know the answer. When I Googled it, I was greeted by a few hundred thousand results, the first dozen or so pages of results all being for places to purchase this particular type of switch, so I thought I would try my luck on the forums of the place that made it.
View 1 Replies
View Related
Dec 6, 2011
I am unable to successfully authenticate my SG200 to either a Cisco ACS or Windows2008 RADUIS server. (C3750x on the same network authenticates fine).
Q1. Is this feature (management login authentication to a RADIUS server) supported on the SG200?
Q2. Is so is there any configuration guidance available for both the SG200 and CSACS / WindowsServer2008 NPS?
I hav not got as far as 802.1x uthentication yet, but config example of this would laso be useful.
View 1 Replies
View Related
Feb 19, 2013
My SG200-50P Switch Log appears as follows with Random ports going up and down. I am trying to find out if this links to another problem I'm having with a Client Server software locking up on the client end. The hardware, thin clients and desktops, are working and have checked all sleep and power settings. All items in working order, now I'm wondering about the switch
2147483369 2013-Feb-20 15:12:07 Warning %STP-W-PORTSTATUS: gi19: STP status Forwarding
2147483370 2013-Feb-20 15:12:02 Informational %LINK-I-Up: gi19
2147483371 2013-Feb-20 15:12:00 Warning %LINK-W-Down: gi19
2147483377 2013-Feb-20 14:51:31 Informational %LINK-I-Up: gi45
2147483378 2013-Feb-20 14:51:28 Warning %LINK-W-Down: gi45
[code]....
View 1 Replies
View Related
Oct 25, 2012
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
View 3 Replies
View Related
Jul 6, 2012
I was configuring link aggregation between a Cisco3750 and Cisco SG200 and the switched network went down just a few minutes after the port channel came on.I rebooted the SG200 and all hosts came back up for a minute before I lost them again. The etherchannel was between two trunking ports. I never set link aggregation on the SG200, could that be the reason? All machines are connected to the SG200. The 3750 is only being used as a layer 3 device for inter vlan traffic.
View 1 Replies
View Related
Jun 1, 2012
Can a Cisco SG300-10P switch power a Cisco SG200-08 switch over POE? Or an SG200-08P power an SG200-08 via POE? I have an area where I'd like to put a small switch, but would like to avoid having to have electrical power run to it. Or will the SG300 and SG200 POE switches only power endpoint devices such as cameras and IP phones?
View 4 Replies
View Related
May 27, 2013
How to setup a port channel between a SG200 and 3750 and am having problems.
What do I need to do on the SG200 I have added the port into the lag but the port will not come up.
I spent half a day messing arround with the web interface and I am unable to get the port to come up.
The Cisco 3750 is a standard port channel config which I have setup maytime before. channel-group 1 mode active channel- protocl lacp Switchport mode trunk
View 1 Replies
View Related
Mar 18, 2012
I manually set an IP address in my new SG200-26, and turned off the dhcp client. I cannot access the webpage or ping the switch at the statically set IP. I have also run a network scan and tried accessing the switch at all of the IP addresses in my DHCP Pool that were being used, it is not available there either.
View 1 Replies
View Related
Mar 21, 2012
I have two separate companys both with staff at two locations and thier own networks connected with a wireless antenna which provides a high speed LAN connection between offices. I only have a single path through this antenna bridge. I have an SG200-08 switch at each end. What I am attempting to do is utlise the switches to take the two subnets at one office, combine them to one for transfer through the antenna bridge, and then resolve them into the two separate networks again at the other end.
View 1 Replies
View Related
Dec 1, 2012
I have a Cisco SG200-08p that's acting up. After setting up 2 larger 200 series switches I pulled this out for its config. I changed the default password and assigned the new static IP address of 192.168.0.103, that's it. The settings applied and worked normally but after rebooting the switch it reverted itself back to the default ip of 192.168.1.254, it retained the new password. After this happened a few times I upgraded the firmware to the latest version, reset the device to factory settings and applied the new address again to have the same problem. It doesn't matter if I reboot the switch in the management interface or physically. Is there a problem with having a zero in the third octet (that would be lame)?
View 6 Replies
View Related
May 23, 2013
I am going to be putting an SG200-08 (8 port switch) inside a 2U rack mount chassis. To enhance cooling I thought I would remove the outer case. Are there, or would there be any issues with using the switch with the cover removed?
View 2 Replies
View Related
Feb 12, 2013
I was given a task of creating a vlan and isolating one pc to access an internal website (192.168.90.15) on a specific port (port 8080)The pc is connected in the following manner:
PC--> HP Switch --> Cisco Small Business SG200 switch --> 3550 Catalyst 1, 3550 Catalyst 2 and 3550 Catalyst 3.
I have created a vlan 110 on the Main 3550 Catalyst switch and successfully added the pc to that vlan.However, that PC must be able to access the internet and an internal website on port 8080.I have placed an access-list on the main 3550 catalyst switch which is connected to our router as below:
Client ip address: 192.168.100.2
VLAN 110: 192.168.100.3
access-list 110 permit tcp host 192.168.100.2 host 192.168.90.15 eq 8080access-list 110 permit icmp host 192.168.100.2 anyaccess-list 110 deny ip 192.168.100.0 0.0.0.255 ? I was unable to access the webserver even after many attempts.
View 2 Replies
View Related
Oct 13, 2011
Does 8.4(2) support snmp v3?
View 1 Replies
View Related
Feb 12, 2012
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
View 1 Replies
View Related
May 28, 2013
Am I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies
View Related
Feb 28, 2012
We're looking for a biz-class router with some service-growth potential. Initially, a wired backbone will be deployed, followed by longer-range Wi-Fi, as far as 400 ft. I'm considering the E4200V2 for deployment in this medium-sized biz environment, but I want SNMP support. Is the E4200V2 a suitable choice? Several reviews have been favorable, but I find no mention of SNMP implementation.
View 2 Replies
View Related
Oct 21, 2012
I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies
View Related
Nov 14, 2011
For some unknown reason our NMS cannot validate SNMP string configured on catalyst switch 4507. SNMP version is 2c
snmp-server community Cisco RO
snmp-server community Cisco RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps entity
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps config
snmp-server enable traps hsrp
snmp-server enable traps syslog
There is Reach ability between NMS server and switch but snmp string is not validating.
View 2 Replies
View Related
Apr 29, 2013
How to get the Snmp OID for polling the in and out utilization for the CIsco 1900 Series Router interfaces.
View 1 Replies
View Related
Sep 3, 2012
I am trying to setup SNMP v3 on a 4948E switch here is what I have done so far:
snmp-server location "location"
snmp-server contact IT Admins
snmp-server group SNMPgrp v3 priv read SNMP-ro write SNMP-rw access 80
snmp-server user snmp_user SNMPgrp v3 auth sha xxxxxxxxx priv aes 128 xxxxxxxx access 80
What else am I missing and how can I confirm that it is configured correctly?
View 2 Replies
View Related
Feb 1, 2013
I have been reading the postings on this site trying to retrieve the MAC address for the client devices (computers, printers) attached to our switches. We have approximately 500 switches and I need to map the mac address to the switch. It appears the OID information is for SNMP v2. We are restricted to using only SNMP v3. I have tried using the Cisco SNMP Object Navigator without any success.
View 2 Replies
View Related
Nov 20, 2011
I am using cisco Nexus5548 and trying to enter a snmp community, but it doesn't accept it. I enter a community name that is less than 32 characters, with symbols, numbers and letters.
View 2 Replies
View Related
Mar 30, 2013
how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
View 2 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Dec 5, 2012
Ive got a 494810ge switch, and this parameters are important for me:
sh int gi 1/4 counters detail
Port InBytes InUcastPkts InMcastPkts InBcastPkts
Gi1/4 252819467437788 173264735013 10827 760
Port OutBytes OutUcastPkts OutMcastPkts OutBcastPkts
Gi1/4 36657317030233 280590958051 5248439 5443194
Port InPkts 64 OutPkts 64 InPkts 65-127 OutPkts 65-127
Gi1/4 558420918 205564441592 2627477631 60865368994
[code]....
Some parameters i can get by snmp (InBytes,InUcastPkts,InMcastPkts, and so on from out), but how can i take other parameters? I would like to do it by snmp but i did not find proper oids. Now I making a sheme like this: eem every 90 seconds takes this info and writes it down to file into nvram and then send it by scp to server, where file is processed by monitoring system script. It is not very good, cause cisco system cpu sometimes spikes of this and i dont know a resourse of nvram, how much times can i write to it?
View 2 Replies
View Related
Jun 12, 2013
Env: Configured Cat3560's L3 port and vlan port, enable OSPF routing, SNMP server, etc. The routing info can be shown by CLI show ip route. But, using SNMP MIB broswer to read IpRouteTable(OID.1.3.6.1.2.1.4.21.1, MIB-II, RFC1213), nothing returned, seems IpRouteTable is empty.I would like to know:
1. Cat3560 works as L3 switch, if it support SNMP IpRouteTable, RFC1213?
2. Where is the Routing table of SNMP, is there specific routing table OID?
3. All the L3 switch has this behavior, or just Cat3560 works like this?
View 8 Replies
View Related
Sep 24, 2012
Is there anyway to pull the usernames and passwords from a switch via SNMP or write a new username and password to switch via SNMP. I have switch that was apparently misconfigured and i am not feeling like driving all the way down there to console in.
View 2 Replies
View Related
Dec 26, 2011
I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
View 1 Replies
View Related
Jul 10, 2012
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
View 4 Replies
View Related
Jun 12, 2012
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies
View Related