Cisco Switching/Routing :: C2950-24 / Unable To Take Control In Console Mode
Jan 25, 2012
I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
View 6 Replies
ADVERTISEMENT
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Mar 6, 2012
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies
View Related
Jan 14, 2012
I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies
View Related
Aug 9, 2012
I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies
View Related
Sep 10, 2012
I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies
View Related
Dec 27, 2012
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
Jun 13, 2012
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies
View Related
Jan 11, 2012
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies
View Related
May 7, 2013
I am trying to configure interface vlan1 to get an ip address from dhcp by entering the commnad ip address dhcp ios rejects the dhcp portion of my command as not recognised although it is referred to in Cisco manuals.my IOS version is c2950-i6k2l2q4-mz.121-22.EA14.bin.I get the same problem when I try to configure ip http secure-server on the switch. Is this a known bug or whether I have the correct IOS version for these commands?
View 6 Replies
View Related
Oct 5, 2008
I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies
View Related
Feb 10, 2011
how to Setup remote control console
View 1 Replies
View Related
Dec 10, 2012
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies
View Related
Mar 12, 2013
I received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
View 2 Replies
View Related
Nov 29, 2011
On a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies
View Related
May 30, 2012
I purchased an old cisco 831 for practical studies for a cisco certification. I purchased the console cable (serial/rj45) and a usb->serial converter cable. However when I open my terminal application (tera term) After I select the right com port (3) and make sure the connection settings are right. It will just sit idle and not show any data from the device. Was I sold a faulty device? It lights up and has three lights on.
Everytime I look at a manual or cisco video I am given the impression the terminal application will just automatically connect. But whenever I try I get nothing.
View 2 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
May 19, 2013
I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies
View Related
Apr 3, 2012
I have a 3560-24ps, and I'm having issues with it booting. When I power the device up all the front panel lights come on like normail, and then the system light starts flashing like normal, but after 5 - 6 seconds the system light goes off. I don't get any output from the console, and the fans still run.
View 5 Replies
View Related
Jun 12, 2013
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies
View Related
Jun 11, 2013
I have two 3560s that i would like to upgrade. But first i would like to make -absolutely- sure i dont wind up in a situation where i have to roll back over a console connection.to the day i still cant understand why oh why someone removed (or chose not to implement it everywhere) tftpdnld from rommon ;)
View 8 Replies
View Related
Dec 16, 2012
Is there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies
View Related
May 3, 2013
I attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies
View Related
Nov 13, 2011
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
View 11 Replies
View Related
Sep 27, 2012
I have 2 3750-x members in a stack running 12.2(58)SE2. I am able to console into the stack master, which happens to be the top switch, but not able to console into the 2nd member. I get the screen stating the console is available but never get the prompt to login. Is this expected behavior?On our stacks of 3750v2's, I'm able to console to any switch in the stack?
View 1 Replies
View Related
Mar 18, 2013
I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
View 3 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Nov 3, 2011
My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
View 3 Replies
View Related
Feb 7, 2013
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies
View Related
Jun 30, 2012
I just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?
View 4 Replies
View Related
Oct 23, 2012
I have a 3750X stack of 6 switches, I have a terminal server console server plugged into the console ports of all 6 switches. I am having a strange issue where I can connect to the master via the console, get a login prompt then I can log in, but when I try and connect to any of the members then I get a prompt "Press RETURN to get started" When I push return, it just loops back to the same prompt again:
switch-6 con0 is now available
Press RETURN to get started.
switch-6 con0 is now available
Press RETURN to get started.
I can connect to the stack via SSH fine etc. I am running 15.0(1)SE2. The stack is configured for TACACS+ auth via Cisco ACS.
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
*1 Master f0f7.55ba.2700 15 1 Ready
2 Member f0f7.5541.da00 14 1 Ready
3 Member a493.4c1e.4b80 13 1 Ready
4 Member f0f7.5585.cb80 12 1 Ready
5 Member a44c.1120.8e80 11 1 Ready
6 Member a493.4cc0.fa80 10 1 Ready
View 4 Replies
View Related
