Cisco Switches :: SF300-08 - Booting With Mode CLI And Not With Console
Nov 29, 2011On a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies
ADVERTISEMENT
Cisco Switches :: SF300-24P Console And Factory Reset
Jan 10, 2012My company just bought a SF300-24P, got it configured without much issue. Today I try to get into it and I can't. Tried via HTTP and console and nothing happens. Decided to try to reset it using the button on the front. Using the documentation, I held down the button for over 10 seconds. Didn't reset to factory defaults, tried again and rebooted it, still nothing. What I am I doing wrong. Also nothing comes up on console window and I'm using the setting for Hyper Terminal that the documentation says I should use.
View 5 Replies View RelatedCisco Switches :: SF300 Switch Supports Configuration Via Console
Mar 1, 2012I am going to purchase SF 300 24p POE Switch and if this Switch supports the configuration via console? As i have ESW-500 Series switches and it does not support console.
View 4 Replies View RelatedCisco Switches :: SF300-24 Layer 3 Mode Routing?
Dec 14, 2012i've a problem with my SF300-24 routing. That's my network configuration:
Port 1 to 12 assigned to VLAN 10
Port 13 to 23 assigned to VLAN 20
Port 24 has an ip 10.17.7.254 to connect with my deafult route, beacuse I've also a Linksys RV042 router, connected in turn with my ISP router, having an ip 10.17.7.1.
Cisco Switches :: SF300-24 Can't Change To Layer 3 System Mode
Mar 16, 2012My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing. When my client received their original switch back, I obviously brought my SF300-24 back to the workshop, reset it back to Factory defaults and tried to do a fresh installation on it. I can not get it to change from Layer 2 to Layer 3! I installed the latest firmware but still no go.
Everything works a 100% via the console, but when I go to the System Mode menu and try and edit it, it justs sits at layer 2 and will not chage to layer 3!
Cisco Switching/Routing :: 1841 - No Console Access When Booting - All Green LED On
Feb 29, 2012today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedCisco Switches :: How To Config VLAN On 2 Switches SF300-24 Layer 3
Oct 6, 2011now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedCisco Switches :: Retrieving ARP Table From SF300 Switches Using SNMP?
May 22, 2012I'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedCisco Switching/Routing :: 2950 Switch Booting Through Monitor Mode
Jul 17, 2012I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 4506e - Booting In ROMmon Mode?
Dec 12, 2012I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedInternet Speed Differs When Booting In Safe And Regular Mode?
Feb 16, 2013When I boot my laptop in safe mode my internet speed is high but when i boot in regular mode, with stopping the right programs for regular mode so my internet speed is high like it is in safe mode.
View 4 Replies View RelatedCisco Switches :: SF300 Phones Not Getting IP
Jun 14, 2011I have a new install with 3 SF300 switches, setup as vlan 2, the switch connected directly to the 2901 router has no problems, plug in a phone and it gets an IP, but if connected to either of the two swtiches behind the first switch, they do not get an IP. I am seeing the DHCP request hitting the router, and the router sending the IP to the phone, but it never gets the IP.
*Jun 15 10:40:20.040: DHCPD: client's VPN is .
*Jun 15 10:40:20.040: DHCPD: Sending notification of DISCOVER:
*Jun 15 10:40:20.040: DHCPD: htype 1 chaddr 40f4.ecef.bded
[Code]....
All ports are setup as trunk on vlan 2 including the ports that connect the switches together. Not sure what the problem is, but they are going live tomorrow and only have 48 out of 120 phones.
Cisco Switches :: Cannot Access VLANS On SF300 24 Over QnQ
Jan 30, 2012Trunk from 3500 going into SF300-8 #1 QNQTrunk from SF300-8 #1 going into trunk SF300-8 #2QNQ from SF300-08#2 going into Trunk SF300-24, All Vlans from Network 1 seem to be communicating properly between the 3550 and SF300-24 and is isolated from the Transport Network by QnQ. I am having one problem, I can not ping the SF300-24 or get to the management interface. I am able to access other devices on the SF300-24 Vlan1 from devices on the 3550 Vlan1 and vice versa.
View 1 Replies View RelatedCisco Switches :: Can SF300-24P Support POE On All Ports
Jun 18, 2012An end user is looking to connect 21x IP Cameras to the switch and they require at least 6W port port. Now, the datasheet states that each port on the SF300 provides 15.4W.I need to double check so that the end user will not start connecting the IP Cameras and then half of them might not fire up.
View 1 Replies View RelatedCisco Switches :: SF300 Does Not Receive IP Address
May 21, 2013cisco 2811 - DHCP server..If IP Phone 3905 installed in SF 300 he does not receive an ip address. [code] If IP Phone 3905 installed in the Catalyst 2960 - all OK.
View 7 Replies View RelatedCisco Switches :: IP Phone Config On SF300-24P
Mar 26, 2013I'm playing with an SF300-24P switch and want to connect an IP Phone. I'm more familar with IOS syntax than the SF300 GUI.
How would I replicate the following in the SF300:
Switch(config)#int fa0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(Config-if)# switchport voice vlan 5
Not sure if setting the port to an ACCESS port on VLAN 15 (i.e. 15UP) and having the Voice VLAN set to 5 is correct.
Or should the port be set to General or Trunk with 15 as the untagged VLAN and 5 as the tagged voice VLAN (i.e. 15UP, 5T)?
Cisco Switches :: SF300-08 - Possible To Have 2 Networks On Different VLANs
May 22, 2011My ISP is providing me with 1 public IP on a /30 network and 14 public IPs on a /28 network. In this example the 10.0.0.1 is the default gw provided by my ISP and 10.0.0.2 is my SF300-08. If I setup my router to route to 10.0.0.2 as the default gw through the interface between the switch and router, can I configure the static routes in the switch to route further to 10.0.0.1?
is it possible to have these 2 networks on different VLANs and configure inter-VLAN routing? I don't want the switch accessible from the 10.0.0.2 IP.
Cisco Switches :: SF300 24p Connection With Vlan
Oct 17, 2012In my network I got 3 SF300 24 p switches. I managed vlan 10 for data and it is also a native vlan and vlan 20 for voice ,1st switch is the core switch and im having a problem in connecting them ?
View 7 Replies View RelatedCisco Switches :: Getting Better Ssh Shell Support On The SF300?
Sep 9, 2012Any chance of getting better ssh shell support on the SF300?Being able to do things like this are very useful:
ssh 10.1.1.1 "sh version"
ssh 10.1.1.1 "sh run"
Cisco Switches :: SF300-48 Cannot Communicate With VLan 2
Jan 2, 2013my new Cisco SF300-48. I want to create 2 vlan (vlan 1 & vlan 2). The switch is set at layer 2. example : vlan 1 (port 1, 2, 3) , vlan 2 (port 4, 5, 6) vlan 1 can communicate each other (port 1, 2, 3) and vlan 2 can communicate each other (port 4, 5, 6)But vlan 1 cannot communicate with vlan 2.
View 4 Replies View RelatedCisco Switches :: Does The SF300 Support Stacking
Jul 20, 2012Does the SF300 support stacking? If it does, which port(s) are the ideal ones?
View 1 Replies View RelatedCisco Switches :: IP Routing VLAN On SF300-24?
Apr 22, 2011I had made a DHCP server that had many scope:
1- scope: 192.168.1.208/28
2- scope: 192.168.1.224/28
3- scope: 192.168.16.0/24
[Code]....
How to condig SF300-24 to vlan 2 vlan 3 can get IP address from DHCP server in VLan 4?
Cisco Switches :: SF300-24p - How To Restore Password
Nov 17, 2012We have a mitel 3300 PBX that is our DHCP server. It feeds an old Foundry Networks switch that nobody knows the password for anymore so I can't even look in it to get some clues. What I think I know is this.
vlan1 = PC's subnet 10.0.0.X 255.255.255.0
vlan2 = phones subnet 10.1.0.X 255.255.255.0
Phones plug into the switch, PC's plug into the phone.
I am assuming this to be the case becase all the PC's get those numbers and when booting up a phone it comes up and says "vlan2 pri 5" during the DHCP discovery.
Like I said the Mitel 3300 is the DHCP server and our internet access is from the firewall's trusted port.
I have put the switch in L3 mode via the console. No matter what I try, the PC will always get IP addresses in vlan2's subnet. Even if I plug the PC directly into the switch.
I have factory reset this baby and all I have done at this point is put it back in L3 and changed the default ip address so I can get to the web GUI.
Cisco Switches :: SF300-24P Technical Specifications
Mar 10, 2013I am looking for some technical specs on the SF300 series which I can't seem to find in the 300 series data sheet: the maximum delay for traffic through the switchbuffer size for each switchportwhether or not the ports are suitable for shielded cable and connectors
View 4 Replies View RelatedCisco Switches :: SF300-48P Option To Telnet It
Jan 14, 2012I have sf300, i didn't found the option to telnet it. default IP of the switch is 192.168.1.254, i can access it by HTTP.
also i'm not able to attach IP phone on voice vlan & computer on vlan 1 ,please share the step by step guide how to access the switch by telnet.
& how to make voice vlan 2 for IP Phones & Vlan 1 for PC.
Cisco Switching/Routing :: C2950-24 / Unable To Take Control In Console Mode
Jan 25, 2012I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
Cisco Switches :: Sf300-08 When Get To Login Screen / Can't Type Anything
Jul 13, 2012After finishing all of my projects here at work, I decided to finally take a look at a sf300-08 that was left by my predecessor. I almost got into it once via browser but the UI crashed. So I downloaded the manual and proceeded to connect to the switch via rs-232. When I get to the log in screen I cant type anything in and when I try hypterterminal crashes.
View 5 Replies View RelatedCisco Switches :: Sf300-24p System Light Flashing?
Mar 14, 2013I changed the setting from static to dynamic and the switch froze up. all lights on the panel flashed, when they stopped the system light on the left side continued to flash. I tryied unplugging unit as well as depressing the reset for longer than 30 seconds. Unit still the same.
View 8 Replies View RelatedCisco Switches :: SF300-24 Is Not Saving Configuration After Reboot?
May 3, 2011I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies View RelatedCisco Switches :: Small Business SF300 Cascade
Mar 5, 2012I have 4 SF300 switches I need to cascade together but the user guides do not seem to cover the physical aspects of cascading the switches.Here is what I was planning.
SW1 (port GB2) --> SW2 (port GB1)
SW2 (port GB2) --> SW3 (port GB1)
SW3 (port GB2) --> SW4 (port GB1)
SW3 (port GB2) --> SW1 (port GB1) - loopback for cascade cable redundancy.
Does this sound about right?after initial use the setup will be changed to place switches 3 and 4 in a factory at which time we will then use the GBIC connectors and fibre to connect SW2 to SW3 and then SW4 back to SW1.
Cisco Switches :: SF300-24P To Get Latest Release Firmware
Mar 24, 2013I have a SF300-24P switch running version 1.1.2.0 firmware. I want to get to the latest release (1.2.9.44) - can I upgrade directly to the latest code or do I need to step through all the versions in between?
View 1 Replies View RelatedCisco Switches :: SRP527W Compatibility With SF300-24 Switch?
Nov 27, 2010I am using a Cisco SRP527W router for our small business. As this device only has 4 LAN ports I want to add another switch so as our business grows I can add more PCs and VoIP phones. I would like to use a Cisco SF300-24 switch and before I purchase am interested to know if anyone has used a SRP527W router with this range of Cisco switches. Are there any compatibility issues or will these two devices work well together?
View 6 Replies View RelatedCisco Switches :: Unable To Get RADIUS Authentication SF300-24P
Feb 19, 2012RADIUS authentication SF300-24P
We have just purchased 20x SF300-24P switches to be installed at our remote offices and we are unable to get RADIUS authentication to work. We already use RADIUS on all our primary network CISCO switches (e.g. 4506s¸ 3560s, 3750s, AP1231Gs,etc) and these work fine so we know the RADIUS server is working.
We are trying to use RADIUS authentication to gain management access onto these switches. Quite simply although we can see that the RADIUS server is accepting the username and password being sent, however the switch says “authentication failed” when to receives the response. We are using Microsoft NPS RADIUS Clients for authentication purposes.
We have upgrade the switches to the latest firmware 1.1.2.0, via the console it seems to have a very cut down IOS version so we cannot use the typical CISCO command set to configure the RADIUS as we normally would. Looking at the web GUI there seems to be a number of options missing including the Accounting port. When debugging is switch on there is no indication to say that any of the settings have been misconfigured.